Router fails to display "DHCP Client List" page


Recommended Posts

gonna state the obvious here but have you tried power cycling the router?

 

i've had similar weird issues before on my moto surfboard that was solved by simply restarting the router

Link to comment
Share on other sites

Start dev mode in your browser I guess and see where it's getting hung up? Then again it could just be the router not loading that page because it's corrupt or something. Backup your settings and flash the firmware again then load your settings back?

Link to comment
Share on other sites

Either you've got a device on your network that the detection script is failing on (Usually a character issue) or it's related to the firmware version you have installed/been dumped with.

 

I've had both happen with various Belkin products that are now serving as access points. I have an Belkin N1 that goes ape-###### trying to detect the hostname of another Belkin router (Which is called BELKIN).

 

It's a non-issue, plenty of good software available to work around network discovery/browsing.

Link to comment
Share on other sites

Start dev mode in your browser I guess and see where it's getting hung up? Then again it could just be the router not loading that page because it's corrupt or something. Backup your settings and flash the firmware again then load your settings back?

How can I check where it's hanging? I use Firefox.

 

Am I right I thinking if I flash an older firmware (I believe the new firmware is the one hanging), I'll loose all the settings? (if so, I can't do this because it's my letting agents that have those settings, I live in a House of Multiple Occupancy).

 

Either you've got a device on your network that the detection script is failing on (Usually a character issue) or it's related to the firmware version you have installed/been dumped with.

 

I've had both happen with various Belkin products that are now serving as access points. I have an Belkin N1 that goes ape-**** trying to detect the hostname of another Belkin router (Which is called BELKIN).

 

It's a non-issue, plenty of good software available to work around network discovery/browsing.

Are you saying there are ways to see who is connected to Wi-Fi other than the router's "DHCP Client List" page?

Link to comment
Share on other sites

King Mustard, on 17 Aug 2013 - 23:10, said:King Mustard, on 17 Aug 2013 - 23:10, said:King Mustard, on 17 Aug 2013 - 23:10, said:

How can I check where it's hanging? I use Firefox.

 

Am I right I thinking if I flash an older firmware (I believe the new firmware is the one hanging), I'll loose all the settings? (if so, I can't do this because it's my letting agents that have those settings, I live in a House of Multiple Occupancy).

 

Are you saying there are ways to see who is connected to Wi-Fi other than the router's "DHCP Client List" page?

 

Lots but some are a lot more complicated than others and your Belkin will limit your success for the easy methods. If you can SSH onto the router for example (Which I doubt for your Belkin I'm afraid), you can show the connected devices on wlan0 via MAC address then marry it up against the list of clients served addresses via the DHCP daemon.

You could run a tool like "Wake On Lan" from Nirsoft which does some easy scanning of local IP / NetBIOS to discover active, dormant and past LAN devices in addition to shouting at them until they wake up.

You could also run your own DHCP server and turn off the router's DHCP service, this will show you who has been served an address on your network and MAC address rules / filtering can allow you to target specific devices.

You can also use Wireshark on your LAN to capture ARP requests which will divulge MAC addresses via sender and destination, so devices communicating on your LAN.

 

EDIT: For a low tech easy method, try Windows Vista/7 Network Discovery Map

Link to comment
Share on other sites

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.