+Warwagon MVC Posted April 29, 2016 MVC Share Posted April 29, 2016 Wondering if anyone owns the Yamaha RX-V679BL. I was wondering if it was possible to disable the OSD (on screen display) when adjusting the volume. The sony I just had and am returning, STRDH750 would output 480p to show the OSD of the volume icon in the bottom of the screen while watching a 1080p video on the my projector. This would make the projector think it just switched resolutions thus the picture would go out and the audio too as it would adjust the picture for 480p each time I would press volume up or down on the remote. Just making sure this one doesn't do that too. Link to comment Share on other sites More sharing options...
+Raze Subscriber² Posted April 29, 2016 Subscriber² Share Posted April 29, 2016 Check page 115 for disabling on screens messages - http://download.yamaha.com/api/asset/file/?language=en&site=usa.yamaha.com&asset_id=64778 it is a bit slow downloading...taken from - http://usa.yamaha.com/products/audio-visual/av-receivers-amps/rx/rx-v679_black_u/ Link to comment Share on other sites More sharing options...
+Warwagon MVC Posted April 29, 2016 Author MVC Share Posted April 29, 2016 1 minute ago, Raze said: Check page 115 for disabling on screens messages - http://download.yamaha.com/api/asset/file/?language=en&site=usa.yamaha.com&asset_id=64778 it is a bit slow downloading...taken from - http://usa.yamaha.com/products/audio-visual/av-receivers-amps/rx/rx-v679_black_u/ Thank you!!! That's what I wanted to know!! and I already looked through the manual!!! Link to comment Share on other sites More sharing options...
+Raze Subscriber² Posted April 29, 2016 Subscriber² Share Posted April 29, 2016 The manual is not laid out very well. I almost bought this receiver, it's a very good choice. Link to comment Share on other sites More sharing options...
+Warwagon MVC Posted April 29, 2016 Author MVC Share Posted April 29, 2016 Just now, Raze said: The manual is not laid out very well. I almost bought this receiver, it's a very good choice. I'm upgrading my theater. what arrived today was that sony receiver I have back in the box ready to get picked up tomorrow for return. Polk Audio PSW505 12-Inch Powered Subwoofer (Single, Black) http://www.amazon.com/Polk-Audio-12-Inch-Powered-Subwoofer/dp/B000092TT0?ie=UTF8&psc=1&redirect=true&ref_=oh_aui_detailpage_o01_s00 Polk Audio CS10 Center Channel Speaker (Single, Black) http://www.amazon.com/Polk-Audio-Center-Channel-Speaker/dp/B0018QROM2?ie=UTF8&psc=1&redirect=true&ref_=oh_aui_detailpage_o01_s02 The other 4 speakers i'm using from my old setup. Unil I order new ones. When I order new ones i'm thinking about 4 of these Sony SSCS3 3-Way Floor-Standing Speaker http://www.amazon.com/Sony-SSCS3-Floor-Standing-Speaker-Single/dp/B00O8YLL8E?ie=UTF8&psc=1&redirect=true&ref_=ox_sc_sfl_title_2&smid=ATVPDKIKX0DER +Raze 1 Share Link to comment Share on other sites More sharing options...
spaceelf Posted April 29, 2016 Share Posted April 29, 2016 (edited) I wouldn't think it'd be an issue with modern kit...my Onkyo HT-S5800 shows the OSD in 1080p. (Probably any other resolution as well, but I don't have any 4k kit to test.) Link to comment Share on other sites More sharing options...
+Warwagon MVC Posted April 29, 2016 Author MVC Share Posted April 29, 2016 Just now, LostCat said: I wouldn't think it'd be an issue with modern kit...my Onkyo HT-S5800 shows the OSD in 1080p. You wouldn't think. A lot of people were complaining about that issue with that sony receiver. It's such a stupid problem which could easily be fixed with a firmware update. Link to comment Share on other sites More sharing options...
+Warwagon MVC Posted May 3, 2016 Author MVC Share Posted May 3, 2016 So the new receiver came today, and it works MUCH MUCH better than the cheaper Sony one Dick Montage 1 Share Link to comment Share on other sites More sharing options...
Dashel Posted May 9, 2016 Share Posted May 9, 2016 You should think about tonally matching your front three instead of mixing them. Link to comment Share on other sites More sharing options...
Dick Montage Posted May 9, 2016 Share Posted May 9, 2016 On 4/29/2016 at 2:44 AM, warwagon said: The sony I just had and am returning, STRDH750 would output 480p to show the OSD of the volume icon in the bottom of the screen while watching a 1080p video on the my projector. This would make the projector think it just switched resolutions thus the picture would go out and the audio too as it would adjust the picture for 480p each time I would press volume up or down on the remote. What a hellishly annoying (IMHO) "design flaw" Link to comment Share on other sites More sharing options...
+Warwagon MVC Posted May 9, 2016 Author MVC Share Posted May 9, 2016 2 minutes ago, Nik L said: What a hellishly annoying (IMHO) "design flaw" There were MANY people on the internet bagging for a simple firmware update which would allow them to turn off the OSD. Of which there wasn't one. Dick Montage 1 Share Link to comment Share on other sites More sharing options...
+devHead Subscriber² Posted May 9, 2016 Subscriber² Share Posted May 9, 2016 On 4/29/2016 at 7:05 PM, warwagon said: I'm upgrading my theater. what arrived today was that sony receiver I have back in the box ready to get picked up tomorrow for return. Polk Audio PSW505 12-Inch Powered Subwoofer (Single, Black) http://www.amazon.com/Polk-Audio-12-Inch-Powered-Subwoofer/dp/B000092TT0?ie=UTF8&psc=1&redirect=true&ref_=oh_aui_detailpage_o01_s00 Polk Audio CS10 Center Channel Speaker (Single, Black) http://www.amazon.com/Polk-Audio-Center-Channel-Speaker/dp/B0018QROM2?ie=UTF8&psc=1&redirect=true&ref_=oh_aui_detailpage_o01_s02 The other 4 speakers i'm using from my old setup. Unil I order new ones. When I order new ones i'm thinking about 4 of these Sony SSCS3 3-Way Floor-Standing Speaker http://www.amazon.com/Sony-SSCS3-Floor-Standing-Speaker-Single/dp/B00O8YLL8E?ie=UTF8&psc=1&redirect=true&ref_=ox_sc_sfl_title_2&smid=ATVPDKIKX0DER I have those Polk center channel and the modest PSW10 subwoofer. Why not get the Polk Monitor 40s for the front channel speakers? Or their floor standing monitors? Polk speakers are going to sound way better than any Japanese counterparts. Many many years ago, a guy I knew who worked at this high-end audiophile shop said that you're fine when getting components from Japan, but speakers should come from US or Britain. They just make better stuff. I don't know if that's still the case, but I would reckon you'd be better off getting all the same brand of speakers. My little Monitor 40s (which are bookshelf speakers) sound exquisite. Link to comment Share on other sites More sharing options...
+Warwagon MVC Posted May 9, 2016 Author MVC Share Posted May 9, 2016 2 hours ago, devHead said: I have those Polk center channel and the modest PSW10 subwoofer. Why not get the Polk Monitor 40s for the front channel speakers? Or their floor standing monitors? Polk speakers are going to sound way better than any Japanese counterparts. Many many years ago, a guy I knew who worked at this high-end audiophile shop said that you're fine when getting components from Japan, but speakers should come from US or Britain. They just make better stuff. I don't know if that's still the case, but I would reckon you'd be better off getting all the same brand of speakers. My little Monitor 40s (which are bookshelf speakers) sound exquisite. Thank you for the information Link to comment Share on other sites More sharing options...
Recommended Posts