GPU temp - 74c Idle - Is this normal?


Recommended Posts

I had temperatures of around 89 degrees idle on my GPU using my stock heatsink for my card, and I since installed an Arctic Cooling Accelro X1 cooler, which lowered my temp to 74 degrees on the GPU and 46 on the chip..Well ATiTool says "temperature of temp chip"..Not sure what that is.

Anyways, are these temperatures perfectly acceptable for an idle PC? This is with the side of my case closed, and the three case fans blowing.

Note: The card is a BFG 6800GT.

I should mention we're on the third floor apartment so with heat naturally rising, I felt I should mention that.

Link to comment
https://www.neowin.net/forum/topic/663012-gpu-temp-74c-idle-is-this-normal/
Share on other sites

I don't have the numbers for GPUs memorized off the top of my head, but like processors, the load temperature is the only one that's important. You figure that and your ambient temperature out while I see what I can find on what the 6800's are good till.

Googled around, Nvidia's released specs for their newer cards..but the older cards don't have anything. I found a review where a shot of the driver showed that 125?C was the "Core slowdown threshold"..however the box looked editable. Anyway, I can't seem to find this stuff, I'd say under triple digits and you're fine.

Alright, thanks for searching around. The highest it got was 85 degrees in WoW, but it was mostly sitting at 81....Considering before I put this cooler on and I had only one working fan on the stock heatsink the temperature went up to 106...I'd say this is a vast improvement heh.

Now I'm amazed I can play CoD4 at 1024 on this card without it over heating.

Edit: Yeah Mystic this is true...But I'm using a cheap Orion PSU, this room in the apartment is one of the hottest, and it's been pretty damn hot lately. I'm hoping those are all big contributing factors. I hope.

I'm actually starting to wonder if ATiTool is giving me an inaccurate number. I just started a stress test with a program, and the card got up to 91 degrees, but as soon as the program closed (really, there was barely any delay) the card dropped to 75 degrees. I couldn't imagine a 16 degree drop in a matter of seconds. Then again, I could be wrong.

I came across other 6800gt users saying their card was at 55 degrees. This is factory overclocked too but I couldn't see it making a 19 degree difference. Although..Maybe I should have mentioned that earlier? >_>

Edited by DigitalManifestations
Well, I got GPU-Z and it's telling me my fan speed is only at 53 percent...That may be part of the problem. Of course, I have no option to change the fan speed in my nVidia control panel.
Get riva tuner.

Riva Tuner should be able to do it. Here's a guide on how to configure v2.09 http://www.vaguetech.com/index.php?pageid=rt207 the one at guru3d doesn't quite have the updated guide.

Thanks for the link Crash.

I'm at 73 idle with the fan at 100 percent, and 78-79 while gaming. It's definitely an improvement. I'd like it to be at 55-60 but like I said, other things may be a factor too such as how hot the apartment is, cheap PSU etc etc.

Thanks for the link Crash.

I'm at 73 idle with the fan at 100 percent, and 78-79 while gaming. It's definitely an improvement. I'd like it to be at 55-60 but like I said, other things may be a factor too such as how hot the apartment is, cheap PSU etc etc.

No problem, glad to help. You can set fan speed profiles if you want, that way once it reaches a certain temp (that you can specify) the fan will adjust it's self based on temperature. Or you can just max the fan speed out, if you can stand the noise. :laugh:

Ambient room temps will have a impact. You can try improving airflow inside the case by routing wires/cables out of the way.

No problem, glad to help. You can set fan speed profiles if you want, that way once it reaches a certain temp (that you can specify) the fan will adjust it's self based on temperature. Or you can just max the fan speed out, if you can stand the noise. :laugh:

Haha. I'm just leaving it at 100. It's actually surprisingly quiet at 100 percent speed.

I am running BFG 6800 Ultra OC, it idle at 62 C. Last month it was idling at around 78-80 C. I took apart the heatsink, cleaned everything and applied Arctic Silver 5. All the heat pads above memory chips was almost gone due to melting of the pads..

Yeah, I cleaned the entire card and the new cooler just came in today, it was spotless. Can dust in other components and fans other than that on the GPU play a role in GPU temperatures?

Ambient temperatures can. As well as other components generating heat that is not being removed by exhaust fans which will subsequently raise your case temperatures which could lead to high GPU temperatures.

Is your CPU having any temperature problems?

Yeah, I cleaned the entire card and the new cooler just came in today, it was spotless. Can dust in other components and fans other than that on the GPU play a role in GPU temperatures?

It can if it's on the case fans. It'll reduce the flow of air somewhat, how much of a difference it'll make, I haven't got a clue.

Ambient temperatures can. As well as other components generating heat that is not being removed by exhaust fans which will subsequently raise your case temperatures which could lead to high GPU temperatures.

Is your CPU having any temperature problems?

This is the first time I've looked at CPU temps...So I'll just post what Speedfan says.

I should note that Speedfan is telling me my GPU is 19 degrees...And it drops to 0 as well heh.

post-45347-1219987172_thumb.jpg

  • 2 weeks later...

I had a similar problem with my 6800GS. When playing GRID the temp would go up to 125C then hit its emergency 'holy crap' mode and slow the hell down to stop it from frying itself.

I took the card out, took off the air duct, and noticed there was a VERY thick wall of dust between the heat sink and the fan (nowhere near the GPU itself) which was stopping any air from the fan from reaching the heat sink. I clean it all up, put it back together and now it idles at a comfortable 41C.

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • When I was a teen, I actually believed that the government used to be always be the bad guy. However as an adult, someone who has actually seen the Law work (though not perfect). I now think everyone cries a river. In this specific case, the so called freedom has consequences to society. Anyone who has seen how child are indeed affected, and I don't mean only extreme things like getting drugs or hate crimen , but no one can deny society as a whole has gone down a rabbit hole due to exesive use of internet. Before anyone calls out that it's the parents responsibility. Yes that's true, but the reality your family/kids might be good people. There are 99% out there who are not and have been brain dead by many things on the internet.
    • Siri AI : iPhone Air, iPhone 17 Pro iPad with M4 and later with 12GB or more in memory Mac with M3 and later with 12GB or more in memory
    • Siri AI will only work locally on these new machines. Not great iPhone Air, iPhone 17 Pro iPad with M4 and later with 12GB or more in memory Mac with M3 and later with 12GB or more in memory
    • Universal Media Server 15.6.0 by Razvan Serea Universal Media Server is a DLNA-compliant UPnP Media Server. UMS was started by SubJunk, an official developer of PMS, in order to ensure greater stability and file-compatibility. The program streams or transcodes many different media formats with little or no configuration. It is powered by MEncoder, FFmpeg, tsMuxeR, AviSynth, MediaInfo and more, which combine to offer support for a wide range of media formats. Because it is written in Java, Universal Media Server supports all major operating systems, with versions for Windows, Linux and Mac OS X. To see a comparison of popular media servers, click here. Universal Media Server 15.6.0 changelog: General Added Discogs integration for audio metadata and UPnP Added new options for DNS resolution handling (thanks, @henry701 Henrique Campos!) Added a loading indicator to the Shared Content area on the web settings (#6037) Improved detection of sample videos Improved stability of speed test (thanks, @henry701 Henrique Campos!) Fixed support for servers with no Internet access (#6047) (thanks, @henry701 Henrique Campos!) Fixed wrong Linux yt-dlp binary being packaged (#6011) (thanks, @Pro-pra!) Fixed API lookups happening for TV series when episode lookup fails, even if the series metadata is already in the local database (#6080) Fixed JDK being used in Docker image instead of JRE (#6089) (thanks, @mvanhorn Matt Van Horn!) Fixed editing a video feed on the web settings erases the URL (#6046) (thanks, @serinekjo kjo!) Fixed docs for FFmpeg GPU support (thanks, @Harshit-dell Harshit Kumar Sahu!) Translation updates via Crowdin Dutch (97%) (thanks, Lefteye!) English (United Kingdom) (80%) (thanks, Andi Chandler!) Italian (63%) (thanks, parduz!) Portuguese (Brazilian) (67%) (thanks, Henrique Campos!) Download: Universal Media Server 15.6.0 | 157.0 MB (Open Source) Download: Other operating systems View: Universal Media Server Website | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
  • Recent Achievements

    • Very Popular
      Captain_Eric earned a badge
      Very Popular
    • One Month Later
      amusc earned a badge
      One Month Later
    • One Month Later
      DJC50PLUS earned a badge
      One Month Later
    • Week One Done
      DJC50PLUS earned a badge
      Week One Done
    • Proficient
      Eric Biran went up a rank
      Proficient
  • Popular Contributors

    1. 1
      +primortal
      509
    2. 2
      PsYcHoKiLLa
      222
    3. 3
      ATLien_0
      92
    4. 4
      +Edouard
      86
    5. 5
      Steven P.
      81
  • Tell a friend

    Love Neowin? Tell a friend!