Enable AHCI on Intel chipsets


Recommended Posts

Some of you might know that AHCI enables Native Command Queuing support and Hot Plugging for SATA drives. Unfortunately it can usually be enabled only when installing Windows, by using a floppy drive.

Spported southbridges: ICH6R, ICH6M, ICH7R, ICH7DH, ICH7M

Instructions:

1) Make sure AHCI is not enabled in your BIOS, otherwise this guide is pointless for you.

2) Back up your Windows folder and prepare a boot disk in case this guide fails!

3) Download 79im05ww.exe from http://www-307.ibm.com/pc/support/site.wss...ocid=MIGR-62909

4) Extract the file to C:\DRIVERS\WIN\SATA.

5) If you have the ICH7M southbridge, go to step 8.

5) Open C:\DRIVERS\WIN\SATA\PREPARE\IMSM_PRE.inf in Notepad.

6) Replace any instance of DEV_27C5 with the following, according to your southbridge:

ICH6R - DEV_2652

ICH6M - DEV_2653

ICH7R - DEV_27C1

ICH7DH - DEV_27C1

ICH7M - DEV_27C5

7) Save the file and close Notepad.

8) Click Start, select Run.

9) In the Open field type C:\DRIVERS\WIN\SATA\PREPARE\INSTALL.CMD and click OK.

10) Restart your computer, and enable AHCI on in your BIOS Setup.

11) Start Windows XP or Windows 2000. The Found New Hardware wizard will start automatically.

12) If running Windows XP:

1. Click No, not this time then click Next.

2. Select Install from a list or specific location (Advanced), then click Next.

3. Select Search for the best driver in these locations.

4. Select Include this location in the search: and specify the path, C:\DRIVERS\WIN\SATA, and click Next.

13) If running Windows 2000:

1. Click Next.

2. Select Search for a suitable driver for my device (recommended), then click Next.

3. Select Specify a location, then click Next.

4. Specify the path, C:\DRIVERS\WIN\SATA, and click OK, then click Next.

14) Click Finish.

15) When the System Settings Change window appears, click Yes. The computer restarts.

Link to comment
https://www.neowin.net/forum/topic/457699-enable-ahci-on-intel-chipsets/
Share on other sites

Confused here. I'm running a single SATA 250GB drive as my primary boot disk. (Well, I've partitioned it into two, but it's one physical drive.) Intel ICH7R southbridge.

No RAID for me, as I've only got one drive, but what advantages will I get if I run my drive in AHCI mode rather than in IDE mode? Can this even be done - this IS the drive I'm booting from...

Confused here. I'm running a single SATA 250GB drive as my primary boot disk. (Well, I've partitioned it into two, but it's one physical drive.) Intel ICH7R southbridge.

No RAID for me, as I've only got one drive, but what advantages will I get if I run my drive in AHCI mode rather than in IDE mode? Can this even be done - this IS the drive I'm booting from...

As I said in the first post:

AHCI enables Native Command Queuing support and Hot Plugging for SATA drives

:no: I am not able to set the BIOS in AHCI mode

I use a Asus P5PL2 mobo with Intel ICH7DH southbridge

I can see in BIOS that the SATA controller use IDE mode for my Seagate Barracuda disk

It is a sata2 disk,and my mobo support sata2 up to 300Mb/s,so I would realy like the sata

controllers to work in AHCI mode.

When I enter BIOS,under IDE configuration,there is a line called:Configur SATA As..,but the only option

is: Standard IDE.As a discription to this option it says:"When in AHCI/RAID mode,controller is forced to

Native mode".

Can anybody please tell me how to configur my SATA drive for best preformence?

Is there a way to configur it to AHCI mode?

I hope somebody has time to help me!

  • 2 months later...
lhost' date='May 3 2006, 09:26' post='587471595']

Some of you might know that AHCI enables Native Command Queuing support and Hot Plugging for SATA drives. Unfortunately it can usually be enabled only when installing Windows, by using a floppy drive.

Can't you enable AHCI by just installing Intel's Matrix Storage Manager/Technology?:

http://www.intel.com/support/chipsets/imsm/

http://www.intel.com/support/chipsets/imst/

  • 1 month later...
  • 1 month later...
  • 2 weeks later...

I literally spent a DAY trying to get AHCI to work. I was trying to load WMCE and after pressing F6, loading the drivers, and watching Windows install....my PC would crash and reboot at the Loading Windows screen (the one you see right after post with the animated bar).

I tried everything I could think of (believe me....that is a lot of stuff....I'm 39 and been building PC's since I was 12)

THIS WORKED LIKE A CHAMP!!!!!!!!!!!!!

THANK YOU, THANK YOU, AND THANKS A HECK OF A LOT!!!!!!

:D :) :laugh: :rofl: :woot: :yes:

One note for anyone attempting this procedure. In step 6 the instructions say REPLACE. Notepad has a REPLACE feature. USE IT! It will keep you from making a typo like another poster did.

  • 4 weeks later...
  • 1 month later...
  • 1 month later...

hi to all! i'm Ruben from italy. I have a p5b deluxe and two 250gb sata2. I would like to know where to connect those hd. I know that there are difference between red and black connector. I would like to know also how to set sata on bios and which driver install. i have read of ahci but i don't understand very well what is it. thank you for your help and sorry for my bad english

  • 1 month later...

Here is the solution (it worked fine for me)

With the BIOS on IDE open Regedit and go to:

HKLM\System\CurrentControlSet\Services\msahci\Start

and change whatever you have on DWORD to '0'

Raboot

Reboot again, enter BIOS

Change IDE to AHCI, Save

Let the OS redetect your drives

Reboot

That's it, hope it helps

  • 3 months later...
  • 2 weeks later...
Any news regarding this guide but with the ICH9 chipset?

I have the P35 chipset w/ ICH9 (Gigabyte P35-DS3R)... with an existing Vista installation I did this:

HKLM\System\CurrentControlSet\Services\msahci\Start

and change whatever you have on DWORD to '0' (default value was 4)

like Ropera mentioned, I installed the Intel Matrix Program/Drivers, rebooted went into Bios... changed from RAID/IDE to AHCI save and everything went fine...

  • 2 months later...

I used that method originally on my Asus P5W DH Deluxe for both Windows XP 32 bits and Vista 32 bits but now I have a double problem:

Now I have a Asus P5K Deluxe with ICH9 and I'm with both Windows XP and Vista x64 edition.

So instead of this drivers version on the firts post (http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-62909), I'll have to get another one right?

I have the P35 chipset w/ ICH9 (Gigabyte P35-DS3R)... with an existing Vista installation I did this:

HKLM\System\CurrentControlSet\Services\msahci\Start

and change whatever you have on DWORD to '0' (default value was 4)

like Ropera mentioned, I installed the Intel Matrix Program/Drivers, rebooted went into Bios... changed from RAID/IDE to AHCI save and everything went fine...

Can you post a print screen of all DWORD keys you have under \Start forlder? Inside mine HKLM\System\CurrentControlSet\Services\ it doesn't even have a \msahci or \msahci\Start forlders, I'm confused :wacko:

Please help me, I'm desperate.

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Linux 7.2's first release candidate gets off to a good start by Paul Hill Credit: Larry Ewing It has been a few weeks since the release of Linux 7.1, and in that time, the Linux 7.2 merge window has been open, where developers can submit their features and patches ready for the upcoming release. That window is now shut, and the release candidate phase has begun so that new features can be tested and further fixes applied. According to the founder of Linux, Linus Torvalds, this week’s release candidate looks “reasonably normal”. Although we are super early in the release candidates, this is a good sign as it makes it more likely that an eighth release candidate will not be needed. Torvalds even mentioned that the update’s stats are only larger than they really are because there was another AMD header drop with a third of the patch just being AMD GPU register definitions, which aren’t big changes but make the code contributed look larger overall. In addition to this, he noted that just over half the patch is drivers, even when excluding the AMD register dump. The rest of the changes are spread out over architecture updates, tooling, documentation, and core kernel updates. In the next week, Torvalds says that he will be chilling out, taking the week “mostly off”. Despite this, he will be reading emails and keeping up with things, so if he is slow responding, now you know why. He said he is hoping for a calm week, but we will just have to see if the second release candidate is actually like that. We should expect seven or eight release candidates before Linux 7.2 is released, so expect it around the end of August. If you missed it a few weeks ago, be sure to check out our coverage of Linux 7.1's release.
    • Ridiculous claim that the labor cost difference of $6000 annually would increase cost per phone by $200. The employees produce 3 phones per month or what?
    • Sparkle 2.20.1 by Razvan Serea Sparkle is a free, open-source Windows optimization tool designed to make your PC faster, cleaner, and more private. With Sparkle, you can easily debloat Windows by removing unnecessary apps and services, disable Microsoft tracking to enhance privacy, and apply performance tweaks to boost speed. Its cleaner removes junk and temporary files, while every change is safe and fully reversible. Sparkle also features a modern, user-friendly interface with automatic updates, making system maintenance simple. Explore over 39 tweaks, from disabling telemetry and hibernation to optimizing network and game settings, all aimed at customizing and enhancing your Windows experience. Sparkle supports Windows 10 and 11. Sparkle 2.20.1 changelog: You can now change the Animation Direction from Up, Left, or Off. Added configurable animation direction (Up, Left, Off) for improved accessibility Added TTL caching to the system info backend Refactored tweak application flow to await NvidiaProfileInspector Improved IPC listener cleanup to correctly remove specific listeners Fixed online status not updating after successful network requests Updated system info tests to support backend caching Removed electron-toolkit utils dependency in favor of internal is.dev helper Fixed unwanted files and folders being included in application bundles Download: Sparkle 2.20.1 | Portable | ~100.0 MB (Open Source) Links: Sparkle Website | Github | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • Never used the G7 Pro, but I've never had a good experience with that style of d-pad and fighting games.
    • And I just bought a seat cushion for my mesh chair. The chair feels nice but the first time I sat in it with boxers, I realized I don't like the feel of mesh on my legs. 😂
  • Recent Achievements

    • One Month Later
      JKR earned a badge
      One Month Later
    • Dedicated
      Asgardi earned a badge
      Dedicated
    • Conversation Starter
      jessse3334 earned a badge
      Conversation Starter
    • Reacting Well
      JuvenileDelinquent earned a badge
      Reacting Well
    • One Month Later
      Excellence2025 earned a badge
      One Month Later
  • Popular Contributors

    1. 1
      +primortal
      496
    2. 2
      +Edouard
      251
    3. 3
      PsYcHoKiLLa
      154
    4. 4
      Steven P.
      86
    5. 5
      macoman
      65
  • Tell a friend

    Love Neowin? Tell a friend!