Enable AHCI on Intel chipsets


Recommended Posts

Some of you might know that AHCI enables Native Command Queuing support and Hot Plugging for SATA drives. Unfortunately it can usually be enabled only when installing Windows, by using a floppy drive.

Spported southbridges: ICH6R, ICH6M, ICH7R, ICH7DH, ICH7M

Instructions:

1) Make sure AHCI is not enabled in your BIOS, otherwise this guide is pointless for you.

2) Back up your Windows folder and prepare a boot disk in case this guide fails!

3) Download 79im05ww.exe from http://www-307.ibm.com/pc/support/site.wss...ocid=MIGR-62909

4) Extract the file to C:\DRIVERS\WIN\SATA.

5) If you have the ICH7M southbridge, go to step 8.

5) Open C:\DRIVERS\WIN\SATA\PREPARE\IMSM_PRE.inf in Notepad.

6) Replace any instance of DEV_27C5 with the following, according to your southbridge:

ICH6R - DEV_2652

ICH6M - DEV_2653

ICH7R - DEV_27C1

ICH7DH - DEV_27C1

ICH7M - DEV_27C5

7) Save the file and close Notepad.

8) Click Start, select Run.

9) In the Open field type C:\DRIVERS\WIN\SATA\PREPARE\INSTALL.CMD and click OK.

10) Restart your computer, and enable AHCI on in your BIOS Setup.

11) Start Windows XP or Windows 2000. The Found New Hardware wizard will start automatically.

12) If running Windows XP:

1. Click No, not this time then click Next.

2. Select Install from a list or specific location (Advanced), then click Next.

3. Select Search for the best driver in these locations.

4. Select Include this location in the search: and specify the path, C:\DRIVERS\WIN\SATA, and click Next.

13) If running Windows 2000:

1. Click Next.

2. Select Search for a suitable driver for my device (recommended), then click Next.

3. Select Specify a location, then click Next.

4. Specify the path, C:\DRIVERS\WIN\SATA, and click OK, then click Next.

14) Click Finish.

15) When the System Settings Change window appears, click Yes. The computer restarts.

Link to comment
https://www.neowin.net/forum/topic/457699-enable-ahci-on-intel-chipsets/
Share on other sites

Confused here. I'm running a single SATA 250GB drive as my primary boot disk. (Well, I've partitioned it into two, but it's one physical drive.) Intel ICH7R southbridge.

No RAID for me, as I've only got one drive, but what advantages will I get if I run my drive in AHCI mode rather than in IDE mode? Can this even be done - this IS the drive I'm booting from...

Confused here. I'm running a single SATA 250GB drive as my primary boot disk. (Well, I've partitioned it into two, but it's one physical drive.) Intel ICH7R southbridge.

No RAID for me, as I've only got one drive, but what advantages will I get if I run my drive in AHCI mode rather than in IDE mode? Can this even be done - this IS the drive I'm booting from...

As I said in the first post:

AHCI enables Native Command Queuing support and Hot Plugging for SATA drives

:no: I am not able to set the BIOS in AHCI mode

I use a Asus P5PL2 mobo with Intel ICH7DH southbridge

I can see in BIOS that the SATA controller use IDE mode for my Seagate Barracuda disk

It is a sata2 disk,and my mobo support sata2 up to 300Mb/s,so I would realy like the sata

controllers to work in AHCI mode.

When I enter BIOS,under IDE configuration,there is a line called:Configur SATA As..,but the only option

is: Standard IDE.As a discription to this option it says:"When in AHCI/RAID mode,controller is forced to

Native mode".

Can anybody please tell me how to configur my SATA drive for best preformence?

Is there a way to configur it to AHCI mode?

I hope somebody has time to help me!

  • 2 months later...
lhost' date='May 3 2006, 09:26' post='587471595']

Some of you might know that AHCI enables Native Command Queuing support and Hot Plugging for SATA drives. Unfortunately it can usually be enabled only when installing Windows, by using a floppy drive.

Can't you enable AHCI by just installing Intel's Matrix Storage Manager/Technology?:

http://www.intel.com/support/chipsets/imsm/

http://www.intel.com/support/chipsets/imst/

  • 1 month later...
  • 1 month later...
  • 2 weeks later...

I literally spent a DAY trying to get AHCI to work. I was trying to load WMCE and after pressing F6, loading the drivers, and watching Windows install....my PC would crash and reboot at the Loading Windows screen (the one you see right after post with the animated bar).

I tried everything I could think of (believe me....that is a lot of stuff....I'm 39 and been building PC's since I was 12)

THIS WORKED LIKE A CHAMP!!!!!!!!!!!!!

THANK YOU, THANK YOU, AND THANKS A HECK OF A LOT!!!!!!

:D :) :laugh: :rofl: :woot: :yes:

One note for anyone attempting this procedure. In step 6 the instructions say REPLACE. Notepad has a REPLACE feature. USE IT! It will keep you from making a typo like another poster did.

  • 4 weeks later...
  • 1 month later...
  • 1 month later...

hi to all! i'm Ruben from italy. I have a p5b deluxe and two 250gb sata2. I would like to know where to connect those hd. I know that there are difference between red and black connector. I would like to know also how to set sata on bios and which driver install. i have read of ahci but i don't understand very well what is it. thank you for your help and sorry for my bad english

  • 1 month later...

Here is the solution (it worked fine for me)

With the BIOS on IDE open Regedit and go to:

HKLM\System\CurrentControlSet\Services\msahci\Start

and change whatever you have on DWORD to '0'

Raboot

Reboot again, enter BIOS

Change IDE to AHCI, Save

Let the OS redetect your drives

Reboot

That's it, hope it helps

  • 3 months later...
  • 2 weeks later...
Any news regarding this guide but with the ICH9 chipset?

I have the P35 chipset w/ ICH9 (Gigabyte P35-DS3R)... with an existing Vista installation I did this:

HKLM\System\CurrentControlSet\Services\msahci\Start

and change whatever you have on DWORD to '0' (default value was 4)

like Ropera mentioned, I installed the Intel Matrix Program/Drivers, rebooted went into Bios... changed from RAID/IDE to AHCI save and everything went fine...

  • 2 months later...

I used that method originally on my Asus P5W DH Deluxe for both Windows XP 32 bits and Vista 32 bits but now I have a double problem:

Now I have a Asus P5K Deluxe with ICH9 and I'm with both Windows XP and Vista x64 edition.

So instead of this drivers version on the firts post (http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-62909), I'll have to get another one right?

I have the P35 chipset w/ ICH9 (Gigabyte P35-DS3R)... with an existing Vista installation I did this:

HKLM\System\CurrentControlSet\Services\msahci\Start

and change whatever you have on DWORD to '0' (default value was 4)

like Ropera mentioned, I installed the Intel Matrix Program/Drivers, rebooted went into Bios... changed from RAID/IDE to AHCI save and everything went fine...

Can you post a print screen of all DWORD keys you have under \Start forlder? Inside mine HKLM\System\CurrentControlSet\Services\ it doesn't even have a \msahci or \msahci\Start forlders, I'm confused :wacko:

Please help me, I'm desperate.

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Windows 11 KB5094126 BSODing, freezing, forcing BitLocker lockout, breaks OneDrive, and more by Sayan Sen Microsoft released Windows 11 KB5094126 and KB5093998 last week as the latest Patch Tuesday updates. Following that the company also published the accompanying dynamic updates under KB5094149, KB5095971, and KB5094156. While Microsoft has so far not acknowledged any major problems with the release, some users online are running into problems. These range from OneDrive and Dropbox access issues, BitLocker recovery lockouts, to blue screens and BSODs. The most common one seems to be happening with HP systems wherein affected users say they hit 0xc0430001 BSOD (blue screen of death) error code after the KB5094126 update. We wonder if this could be related to the recent bug we covered on HP devices wherein the ongoing Secure Boot certificate updates are leading to similar issues. While we are not certain, users affected by this issue likely need to ensure that the boot.stl file is included on the installation media (such as a USB installer or ISO), if the above-mentioned dynamic updates are deployed. If this file is missing, computers may fail to boot from the installation media and could display the error 0xc0430001. This STL file is used by Secure Boot to verify that the boot files are trusted, so it must match the same Windows version and system architecture. To ensure the file is included, Microsoft recommends using the Update WinPE script, which automatically updates the image and handles the required files. Alternatively, you can manually copy the boot.stl file from the Windows\Boot\EFI folder on a Windows device and place it in the matching folder on your installation media before deploying the updated image. Aside from blue screening some users also note their systems have been freezing following the update. This could be happening to Lenovo PCs specifically. In the case of the OneDrive and Dropbox access issues, a user figured out that there could be a conflict with UAC. He explained: "Okay, so I did some digging, and in our environment KB5094126 breaks OneDrive and Dropbox in Explorer. I went through all our GPOs and found out that the combination of disabling UAC and having my user being a local admin breaks OneDrive in Explorer. ... If I enable UAC again, then it works, even with KB5094126 still installed." Hopefully, Microsoft will look into these issues. Source: Microsoft forum (link1, link2, link3, link4), Reddit (link1, link2, link3, link4)
    • It is when it's a desktop in my house though for a PC that's lightly used and not really important when it is. If it was a laptop, it would be a different story. The real solution is varied and begins starting at post #22 in that thread.
    • Win11Debloat 2026.06.14 by Razvan Serea Win11Debloat is a lightweight, easy to use PowerShell script that allows you to quickly declutter and customize your Windows experience. It can remove pre-installed bloatware apps, disable telemetry, remove intrusive interface elements and much more. The script also includes many features that system administrators and power users will enjoy. Such as a powerful command-line interface, support for Windows Audit mode and the option to make changes to other Windows users. All changes made by Win11Debloat can be easily reversed, and most removed apps can be restored via the Microsoft Store. A full guide on how to undo the changes is available here. Win11Debloat features: Below is an overview of the key features and functionality offered by Win11Debloat. Please refer to the wiki for more information about the default settings preset. Remove a wide variety of preinstalled apps. Click here for more info. Disable telemetry, diagnostic data, activity history, app-launch tracking & targeted ads. Disable tips, tricks, suggestions & ads across Windows. Disable Windows location services & app location access. Disable Find My Device location tracking. Disable 'Windows Spotlight' and tips & tricks on the lock screen. Disable 'Windows Spotlight' desktop background option. Disable ads, suggestions and the MSN news feed in Microsoft Edge. Hide Microsoft 365 ads on the Settings 'Home' page, or hide the 'Home' page entirely. Disable & remove Microsoft Copilot. Disable Windows Recall. Disable Click to Do, AI text & image analysis tool. Prevent AI service (WSAIFabricSvc) from starting automatically. Disable AI Features in Edge. Disable AI Features in Paint. Disable AI Features in Notepad. Disable the Drag Tray for sharing & moving files. Restore the old Windows 10 style context menu. Turn off Enhance Pointer Precision, also known as mouse acceleration. Disable the Sticky Keys keyboard shortcut. Disable Storage Sense automatic disk cleanup. Disable fast start-up to ensure a full shutdown. ...and more. Once you’ve downloaded the Win11Debloat file (Get.ps1), just follow these quick steps: Locate the Get.ps1 script file. Right-click the file and select Run with PowerShell from the context menu. If prompted by User Account Control (UAC), select Yes to grant the script the necessary administrative permissions. Win11Debloat 2026.06.14 changes: This is a minor release that hopefully addresses the false positives in Windows Defender and Bitdefender that prevented users from downloading and/or running Win11Debloat. Refactor Get-RegFileOperations.ps1 to address false positives by @Raphire in #626 Add logging around WinGet app retrieval and increase timeout to 20s by @Raphire Download: Win11Debloat 2026.06.14 | Open Source View: Win11Debloat Home Page | Screenshots 1| 2 Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • Still using Microsoft Money 2005 in 2026 here!
  • Recent Achievements

    • Week One Done
      Jeroen Wilms earned a badge
      Week One Done
    • Week One Done
      rolfus earned a badge
      Week One Done
    • One Month Later
      Leroy Jethro Gibbs earned a badge
      One Month Later
    • Conversation Starter
      flexorcist earned a badge
      Conversation Starter
    • One Month Later
      AndreaB earned a badge
      One Month Later
  • Popular Contributors

    1. 1
      +primortal
      508
    2. 2
      +Edouard
      198
    3. 3
      PsYcHoKiLLa
      139
    4. 4
      ATLien_0
      90
    5. 5
      Steven P.
      82
  • Tell a friend

    Love Neowin? Tell a friend!