Fridge, whats more efficient, fully stocked or just what you need.


Recommended Posts

so what would be more energy efficient, filling the fridge full or just putting in a few things?

the way i see it, if you fill the fridge, the items keep the fridge colder for longer, but it will take long to cool them. meaning longer periods before the compressor kicks in.

partially full, there is less items in the fridge that hold the coldness, so the fridge has to come on more often but for short periods to cool the few items.

obviously it would take more energy to cool the items from room temp to the fridges set temp, but i'm talking about maintaining the temps once they are atcheived.

I'm not a Hippy, things like this don't bother me

oh be quiet, I'm not a hippie either, but I don't like wasteing my darn money on electric... it DOES cost me something for a fridge to run less efficient... saving money != hippie

I bought the most energy efficient fridge I could when I bought my new house, why? because I spent all my darn money buying a house, I wanted to save money on electric bills!

the way i see it, if you fill the fridge, the items keep the fridge colder for longer, but it will take long to cool them. meaning longer periods before the compressor kicks in.

partially full, there is less items in the fridge that hold the coldness, so the fridge has to come on more often but for short periods to cool the few items.

That's what I say too. A fridge has a sensor and the compressor kicks in when the temp reading is above the set temp. Less things in there should mean less run time, and therefore it should be more efficient.

That's what I say too. A fridge has a sensor and the compressor kicks in when the temp reading is above the set temp. Less things in there should mean less run time, and therefore it should be more efficient.

but then you get people say the complete opposite, more things = more cooling stored so less cooling needed... no idea what to believe... i think what people need is better insulated fridges, and higher efficiency compressors not more or less in it

I'm guessing there's a peak efficiency somewhere in between near empty and near full. If the fridge is too full, then the fridge has to work harder to move enough air to keep everything cool. But if the fridge is too empty, this will mean greater fluctuations in temperature, though I'm not sure if this mean the fridge runs more often or for longer.

We have 5 levels of chill on our fridge, when it's not very well stocked I knock it down to the lowest. When it's rammed, I turn it up to the highest.

firstly that's a temperature setting, unless your fridge is from like the 50's. secondly it should be set to 4 unless your fridge setting is wrong, put a thermometer in it, and set it to whatever setting gives it 4 degrees Celsius inside. in fact it's likely that when you turn "down" the fridge, you're actually setting it colder and this using more energy. depend on the manufacturer though.

either way you shouldn't adjust the setting based on the amount of food, it should be adjusted to whatever setting gives you 4 degree celsius.

  • Like 1

oh be quiet, I'm not a hippie either, but I don't like wasteing my darn money on electric... it DOES cost me something for a fridge to run less efficient... saving money != hippie

I bought the most energy efficient fridge I could when I bought my new house, why? because I spent all my darn money buying a house, I wanted to save money on electric bills!

Actually, a fridge, uses EXTREMELY little energy, provided you don't keep the door open. but among the electric goods in your house, the fridge uses least of all most likely.

the amount of food in the fridge doesn't matter, as the OP sort of figured out in his original reasoning, it'll use the same amount of energy, just either take longer between using the compressor or using it shorter for more often. but even this won't matter much.

The only thing you have to check, and this has nothing to do with energy use is that you don't put hot food in the fridge. the reason for this is that it increases the temperature in the fridge, won't really affect energy use, but you shouldn't increase the temp it causes food to go bad faster and condensation. some fridges allows you to lower the temperature two r so degrees before putting in food. But this button has to be pressed well in advance of actually putting in food. (Think the day before when you know you're going to the store to buy food for the whole month). Freezers often also have this setting and allows you to press the freeze in button the day before shopping, and will lower the temperature from -18 to -22 to -24 freezing the food faster and reducing/preventing the temperature increase in the freezer.

But for anyone who wants to save energy, the Fridge, freezer and dishwasher are the least of your problem, the one thing that costs you most energy in your house, hot water. (provided you're the one providing the power to the water heater.

I have a Fridge/Freezer combo unit and I can set the temp for each compartment. I'm glad we got that kind instead of a 5 setting deal. We usually set the Fridge for 36 and the Freezer for 0. I have no idea if that is the ideal settings but it works for me.

but then you get people say the complete opposite, more things = more cooling stored so less cooling needed... no idea what to believe... i think what people need is better insulated fridges, and higher efficiency compressors not more or less in it

Provided the fridge is fairly new (less than 30 or so years) the insulation isn't a problem. the fridge is efficient enough anyway. The new fridges do however have better insulation, however, this is used to make thinner walls on the fridges and give more usable volume. as the fridge insulation is already efficient enough, after all, your fridge walls don't feel cold to the touch do they.

I have a Fridge/Freezer combo unit and I can set the temp for each compartment. I'm glad we got that kind instead of a 5 setting deal. We usually set the Fridge for 36 and the Freezer for 0. I have no idea if that is the ideal settings but it works for me.

if it translates to +4 celsius and -18 celsius, it's correct.

so what would be more energy efficient, filling the fridge full or just putting in a few things?

the way i see it, if you fill the fridge, the items keep the fridge colder for longer, but it will take long to cool them. meaning longer periods before the compressor kicks in.

partially full, there is less items in the fridge that hold the coldness, so the fridge has to come on more often but for short periods to cool the few items.

obviously it would take more energy to cool the items from room temp to the fridges set temp, but i'm talking about maintaining the temps once they are atcheived.

Figure out how much space you need and fill the rest with two liter bottles of water.

Actually, a fridge, uses EXTREMELY little energy, provided you don't keep the door open. but among the electric goods in your house, the fridge uses least of all most likely.

the amount of food in the fridge doesn't matter, as the OP sort of figured out in his original reasoning, it'll use the same amount of energy, just either take longer between using the compressor or using it shorter for more often. but even this won't matter much.

The only thing you have to check, and this has nothing to do with energy use is that you don't put hot food in the fridge. the reason for this is that it increases the temperature in the fridge, won't really affect energy use, but you shouldn't increase the temp it causes food to go bad faster and condensation. some fridges allows you to lower the temperature two r so degrees before putting in food. But this button has to be pressed well in advance of actually putting in food. (Think the day before when you know you're going to the store to buy food for the whole month). Freezers often also have this setting and allows you to press the freeze in button the day before shopping, and will lower the temperature from -18 to -22 to -24 freezing the food faster and reducing/preventing the temperature increase in the freezer.

But for anyone who wants to save energy, the Fridge, freezer and dishwasher are the least of your problem, the one thing that costs you most energy in your house, hot water. (provided you're the one providing the power to the water heater.

I just picked a random energy star rated fridge from lowes... averages 448 KW/h a year.. that's about on average $60 to run... that's an efficient one... a non energy star one now 890 KW/h.... I don't care if it "uses less then everything else in your house" it still adds up.... 500 KW/h less a year is still $60 a year I don't have to spend on electric :) but the reason I used this example, is because how stocked the fridge is really does not matter, it's how efficient the compressor is and how much its opened

That's what I say too. A fridge has a sensor and the compressor kicks in when the temp reading is above the set temp. Less things in there should mean less run time, and therefore it should be more efficient.

I agree with this. Cause it works for a freezer. Fill the freezer so it holds the cold longer. put more in a cooler to keep things cooler longer. Why would you put less ice in a cooler? ;)

you americans and your oversized crazy fridges.

anyway the amount of stuff in the fridge won't affect the energy used. we don't use energy star over there though, they're all marked with the new EU energy rating, and all fridges are A nowadays meaning they had to ad A+, A++, and A+++

Looking at a fairly big (180tall, 350 liter) pure fridge, with an A+ rating. It uses about 139 KWh a year,

a similar A++ Samsungs (180, 350L) uses 118, effectively over the year there's no difference. besides anyone who buys Samsung white goods will be tearing their hair out for other reasons than power bills anyway.

I can't even imagine a fridge using 450 KWh a year, much less almost 900. That must be some American made stuff, using same technology you use to make engines, whole lot of liter, not a lot of horsepower :p

Just to get the 450 value to make any sense I would have to imagine an oversize two door fridge. Which will use a lot more energy since the energy marking will usually count an opening as opening both doors, and even if you open just one, the double ones are horribly inefficient in that the inside temperature goes down a lot more. you'd be far better of with two single fridges side by side.

seriously... how is 890 even possible... heck I can't even get 450 to make sense....

I agree with this. Cause it works for a freezer. Fill the freezer so it holds the cold longer. put more in a cooler to keep things cooler longer. Why would you put less ice in a cooler? ;)

Doesn't matter the net energy usage is the same.

More stuff in the freezer, means longer time for the compressor to stay one, and longer between each time it goes one.

Less stuff in the freezer means faster to cool down, but also shroter times between on periods.

in the end the net result is the same, just 1+1+1+1+1+1+1+1=8 instead of 4+4=8.

I think it's a better question to ask: will you eat all the food you have in your refrigerator before it goes bad? That's why me and my wife keep only what we'll eat over the next few days so nothing goes bad. Makes the fridge look pretty empty, but oh well.

you americans and your oversized crazy fridges.

anyway the amount of stuff in the fridge won't affect the energy used. we don't use energy star over there though, they're all marked with the new EU energy rating, and all fridges are A nowadays meaning they had to ad A+, A++, and A+++

Looking at a fairly big (180tall, 350 liter) pure fridge, with an A+ rating. It uses about 139 KWh a year,

a similar A++ Samsungs (180, 350L) uses 118, effectively over the year there's no difference. besides anyone who buys Samsung white goods will be tearing their hair out for other reasons than power bills anyway.

I can't even imagine a fridge using 450 KWh a year, much less almost 900. That must be some American made stuff, using same technology you use to make engines, whole lot of liter, not a lot of horsepower :p

Just to get the 450 value to make any sense I would have to imagine an oversize two door fridge. Which will use a lot more energy since the energy marking will usually count an opening as opening both doors, and even if you open just one, the double ones are horribly inefficient in that the inside temperature goes down a lot more. you'd be far better of with two single fridges side by side.

seriously... how is 890 even possible... heck I can't even get 450 to make sense....

Doesn't matter the net energy usage is the same.

More stuff in the freezer, means longer time for the compressor to stay one, and longer between each time it goes one.

Less stuff in the freezer means faster to cool down, but also shroter times between on periods.

in the end the net result is the same, just 1+1+1+1+1+1+1+1=8 instead of 4+4=8.

Didn't know LG and Samsung was american made, so, yeah attempt to troll america = fail...

please show me a fridge that is standard size in the USA below 400 KW/h? Heck most of the normal fridges I've looked up for European areas are not too different in size or wattage, only difference is a lot of them run on 220v instead of 110v

heck this small 4.4 cubic ft firge still uses 274 KW/h on average in a year

http://www.lowes.com...r%7C1=

and that is a whole 4.4 cu ft small one! I think your idea of how much electric a firdge uses is a little skewed

I just looked up the same LG one I looked up for the USA at 450 watts, the UK version uses a whole......461 watts and is rated A+ and that was 352 cu liter

For the refrigerator, I don't know that you would see a difference in terms of electricity either way, or I should say, it depends on the refrigerator. For the freezer, yeah, fill it up, it'll keep it colder, and should you lose power, the food will keep longer.

and that is a whole 4.4 cu ft small one! I think your idea of how much electric a firdge uses is a little skewed

Except I sell them as part of my job, an as I demonstrated above a 180 tall 350L fridge, is from 140 KWh a year. 400+ is just ridiculous.

I looked up a cheap ass Beko (cheap crap store brand). that is a double wide with freezer. it's listed at 455KWh a year. BUT the bottom of this is a freezer so it'll use a lot more of course, and it'll lose almost twice as much energy because it's a double door fridge and freezer. and because the way euro energy marking is done, both doors have to be opened when measuring energy usage (they're opened a certain amount of times per day, equal to the average amount of times a family would open the fridge) which would let in a lot more hot air than opening just one which any sensible person at home would. you can pretty much assume that 75% of those 455KWh is the freezer though.

And while I would never buy any Samsung white goods myself, some of their fridges actually have a clever solution with a bar door. A small "flap" door that you can open to get stuff form the middle shelf, like milk or drinks or anything really, this would pretty much reduce your energy usage by a significant amount as it would allow you to lose far less energy when getting stuff for lunch or stuff like that.

lesson learnt from this, if you want to save money on your fridge, don't keep the door open. put however much or little in it as you want, keep it at 4C. but don't keep the door open more than you have to.

Either way, I don't see any reasonable way pure ridge would use even half of 400 KWh a year.

Also don't argue the energy usage with a European since Europe has REALLY strict rules about the energy usage, we're not even allowed to sell white good below a certain energy grade, and at store ALL white good must be marked with the euro standard energy markings, which lists all the energy usage and vital details of the product.

Except I sell them as part of my job, an as I demonstrated above a 180 tall 350L fridge, is from 140 KWh a year. 400+ is just ridiculous.

give me model numbers, because I want to see what is out there, everything I've looked up is similar to the USA models

Samsung Twin RR82FESW1 - Class A+ 139KWh

Samsung Twin RR82HFBC - Class A++ 112KWh

Beko GNE114612W - 455KWh, combined dual door fridge and freezer, this one is high because of dual doors and mostly the freezer part.

and some high quality stuff to compare

http://www.miele.no/no/husholdning/produkter/1278_K_13820_SD-50384.htm

390L, 155KWh, Energy class A+

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • OpenClaw now has native mobile apps on iOS and Android by Karthik Mudaliar OpenClaw, the viral open-source personal AI agent, now has its own mobile app, available on both Android and iOS. Users can pair the app with an existing OpenClaw gateway and can start using new mobile-native features that are now available on the app. The app supports all the existing features you'd already have seen on OpenClaw's TUI, as well as some more, such as real-time and background Talk mode, action approvals, sharing from iOS, and optional access to device capabilities such as camera, screen, location, photos, contacts, calendar, and reminders. These features are available on both the Android and iOS versions of the app. What's important with these apps is that they don't run OpenClaw on your phone, but are actually just companion apps that require a running OpenClaw Gateway on an existing device, on macOS, Linux, or Windows via WSL2. To pair the app with your existing OpenClaw gateway, users need to run the command "/pair qr" on the TUI or existing chat interface, which brings up a QR code. Users can then scan this QR code to pair it up with the mobile app. There's also an option to manually pair the app by entering the host and a port. Previously, OpenClaw had been available on phones via WhatsApp, Telegram, Slack, Discord, Microsoft Teams, Matrix, and others. Now, with a native mobile app, the interface is much cleaner and more focused on just the OpenClaw, of course, with the added support for camera, screen, location, and more. It's important to note that OpenClaw comes with its own security warnings. There's always a chance of prompt injection with these tools, so users are recommended to double-check authentication, tool policy, sandboxing, and execution approvals rather than prompts alone. For users well-versed with the AI harness, a native mobile app makes it easier to approve an automation, share a link, use voice, or let an agent react to phone-side context.
    • Google pitches Spanner as one database for all AI agents with these new featues by Karthik Mudaliar Google Cloud is introducing new features within Spanner, its distributed database, as a place where enterprises should keep their data, using which AI agents could make smarter and better decisions. In a detailed blog post, Google highlighted quite a few features coming to Spanner, including relational data, graph relationships, vector search, key-value access, full-text search, and operational analytics together in one database architecture. Google says that today's systems aren't well-made for AI agents. There could be data that is present in one system, search indexes in another, embeddings in a vector database, and relationship data in a graph database. This fragmentation isn't great for AI agents to do their jobs because they don't have access to all of this data in one place. This is where Google is positioning Spanner as a solution. Spanner is already a globally distributed relational database with strong consistency, and Google wants its customers to see it as a broader data layer for AI applications. The company introduced something called Spanner Graph, along with integrated vector search, full-text search, a Cassandra-compatible key-value endpoint, and a columnar engine for analytical queries on operational data. Google also added that its ScaNN-powered vector search can support indexes with more than 10 billion vectors, while the columnar engine can make some analytical scans up to 200 times faster. All of this isn't just exclusive to the Google Cloud Platform, and there's support for multi-cloud as well. This comes via Spanner Omni, which Google says is a downloadable, containerized version of Spanner that can run on Kubernetes and in environments outside Google Cloud, including Microsoft Azure and AWS, and even on-premises infrastructure as well as edge deployments. Google says that customers who are interested in the full-featured edition should contact the company, and there's no word on commercial availability or separate pricing. Those interested can read the full blog by Google Cloud, which details these features individually.
    • Kalmuri 4.2.5 by Razvan Serea Kalmuri is your all-in-one, portable screen capture and recording solution designed for speed, simplicity, and flexibility. Whether you need a full-screen snapshot, a custom area, a scrolling webpage, or smooth video recording, Kalmuri delivers with ease. Capture text instantly from images with built-in OCR, keep floating images on top for quick reference, and use the precise color picker for perfect design matching. Customize hotkeys to work your way and share results instantly with built-in upload options. Kalmuri runs without installation, making it ideal for USB use, and offers an intuitive interface that’s easy to learn. Kalmuri key features: Video recording support (designation of whole screen and area) Whole screen, active program, window control, area application Extract text from images using optical character recognition (OCR). Support for PNG, JPG, WEBP, BMP, GIF file formats MP4 video recording powered by FFmpeg for high-quality results Full web page capture Share the captured image on the web Color extraction function Printer output Hotkey settings Adjustable via keyboard for area capture (Arrow key, Ctrl+Arrow key, Shift+Arrow key) File name format (sequential, datetime) Free to use it at work, at home, in government offices, at school, etc. Using Kalmuri portable for video recording Kalmuri’s portable version doesn’t include FFmpeg, which is required for video recording. Without it, you’ll get an “error FFmpeg.exe not found” message. To fix this, download FFmpeg from the provided link, extract it, and place FFmpeg.exe in Kalmuri’s folder. Kalmuri will then recognize it automatically, allowing you to start recording in high quality instantly. Kalmuri 4.2.5 changelog: Fixed an intermittent crash when using Area Capture Improved stability for Area Capture and screen recording Resolved a capture issue that could occur right after startup Download: Kalmuri 4.2.5 | 24.2 MB (Freeware) Download: Kalmuri Portable 4.2.5 | 2.1 MB View: Kalmuri Website | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • They have lots of info on me, I have a facebook account and have done so for years, it was the thing to have then. My phone number is not on it. I don't have the Facebook app on my phone these days, just the messenger part, and only for a couple of people to contact me, most will text me via SMS or phone. I agree, Meta, like others, even without an account will know something about me. Just have to try and keep some things private Also, never saw the need for Whatsapp, people used to ask for me to join it, but as I said to them, I have SMS and a phone, use that, or email
  • Recent Achievements

    • First Post
      rosiecharles earned a badge
      First Post
    • Reacting Well
      Juan Dela earned a badge
      Reacting Well
    • Week One Done
      Collagen Project earned a badge
      Week One Done
    • Reacting Well
      Wakeen1966 earned a badge
      Reacting Well
    • Rookie
      Almohandis went up a rank
      Rookie
  • Popular Contributors

    1. 1
      +primortal
      516
    2. 2
      +Edouard
      273
    3. 3
      PsYcHoKiLLa
      143
    4. 4
      Steven P.
      98
    5. 5
      macoman
      54
  • Tell a friend

    Love Neowin? Tell a friend!