Recommended Posts

Don't see why it would be bad as long as you've got drivers for everything and Windows is behaving. Personally I'd only really consider x86 for systems that obviously couldn't run x64 (old Athlon XP's, etc or have old hardware that doesn't have 64 bit drivers), or systems that only have like 2GB memory where 64 bit would probably do more harm than good due to the overhead.

This PC has never run x64. The specs are pretty low, 1.5GB RAM, 3GHz single-core processor. I was just worried that it might not last long until it crashes or something.

Don't worry, x86 or x64 will not cause your hardware to fail on its own

x64 has its advantages over x86 if your machine can run it, if you only have a couple gigs of RAM, then x86 is probably better, but neither is going to waste your hardware any faster

EDIT - How did you install Win 8 on 1.5GB of RAM ?

This PC has never run x64. The specs are pretty low, 1.5GB RAM, 3GHz single-core processor. I was just worried that it might not last long until it crashes or something.

That's surprising, the Win 8 installer let you do the install? The minimum RAM for Win 8 64-bit is 2 GB, it doesn't sound like the machine meets the minimum requirements.

Without thinking, I installed Windows 8 64-bit on my old PC from 7 years ago that initially ran Windows XP, and I upgraded it to Windows 7 32-bit when it came out. Now I've upgraded it to 64-bit since I upgraded my other computer.

Is this bad? Should I install 32-bit instead?

why??? old hardware, new windows = never a good deal. drivers missing, slow / poor performance... the list goes on.

But hey, if you are happy with it.. i once installed Windows XP on my old trustee Pentium 200 MMX that came with Windows 95; sure it worked (upgraded everything on that puter except the board, PSU and CPU) but i could eat lunch or take a nap while the puter was booting :laugh: :woot: still did lots of Photoshop work in that, though. :rofl:

I don't see why it should be a problem if the hardware supports it. The 64-bit version requires more RAM (I think 2GB whereas 32-bit only needs 1GB). Are you having any issues? If not then I don't see a problem.

Unless you run XP, there is absolutely ZERO reason to run anything other than an x64 OS on hardware that will support it. (And even if you DO run XP, the support for x64 by XP-era hardware is a lot greater than you would think - the issue iwth XP64 and support is applications - not hardware.)

Look in the Hardware Hangout archives - I've made several posts covering migration from x32 to x64 over XP, Vista, and 7 - including my own migration (during the Vista era). The issue has by and large been applications-related, and especially since the release of Windows Vista - between that and just plain FUD, crossover was scarce during the Vista era.

Unless you run XP, there is absolutely ZERO reason to run anything other than an x64 OS on hardware that will support it. (And even if you DO run XP, the support for x64 by XP-era hardware is a lot greater than you would think - the issue iwth XP64 and support is applications - not hardware.)

There are plenty of reasons not to run 64-bit on old hardware. The biggest one being that 64-bit uses more resources and creates more processes. The OP having 1.5GB of RAM is going to be hurting himself in performance by running x64. And finding drivers will be a nightmare. Honestly, the only upside I can think of for him to run x64 would maybe be security. And even that's a stretch.

Plus, I think we first need to know the specific CPU he's running. There are very few single-core CPUs out there that support x64, so he might be mistaken in thinking a Pentium 4 or something supports it, when in reality it doesn't.

  • Like 2

Unless you run XP, there is absolutely ZERO reason to run anything other than an x64 OS on hardware that will support it.

Maybe for home PCs, definitely not for office/corporate PCs. There's a huge amount of software, middleware, plugins, drivers, etc. that are specifically 32-bit. Getting this type of stuff to work in a 64-bit environment is often difficult or impossible, good luck trying justifying all the extra expenses to your boss/client. And frankly, most office PCs won't have more than 4 GB RAM.

But yeah, if all the software/hardware you're using is 64-bit compatible & you have 4+ GB RAM then it makes sense to go 64-bit.

Maybe for home PCs, definitely not for office/corporate PCs. There's a huge amount of software, middleware, plugins, drivers, etc. that are specifically 32-bit. Getting this type of stuff to work in a 64-bit environment is often difficult or impossible, good luck trying justifying all the extra expenses to your boss/client. And frankly, most office PCs won't have more than 4 GB RAM.

But yeah, if all the software/hardware you're using is 64-bit compatible & you have 4+ GB RAM then it makes sense to go 64-bit.

Again, you are referring to application issues - not hardware issues. (I specifically mentioned applications as being the bugbear with Windows in general, and XP in particular, in terms of migrating to x64 - I covered it in my posts covering migrating folks I support to x64 - starting with, in fact, XP64.) Further, NONE of my migratees had 4 GB of system RAM at the time of migration. None at all. (Over half had less than 2 GB of RAM - two had a mere 512MB of RAM. However, all of these were home users - not corporate or enterprise users. However, most were also using refurbished corporate or enterprise PCs - which shipped with either Windows XP Professional or even Windows 2000 Professional. Nearly the WORST of possible cases for an x64 migration; however, due to the lack of application issues with home users, I had far easier a time than would have been suspected.

The 4 GB issue - go back to Hardware Hangout and read my posts again. I started the migration trend because of - not in spite of - what I uncovered in my investigation of this particular rubric. My uncovering is, in fact, easily duplicated by anyone with access to virtualization software - simply configure identical virtual machines with each OS in the consideration pool. (Naturally, the host must support at least VT-X for both x32 and x64 to face off in this manner.) The virtualization software itself won't matter. Once the application and driver issues are addressed, the 4 GB floor is, in reality, half that. (It can be , in fact, lowered all the way down to a single gigabyte of RAM - or less - for computers used exclusively for Internet-based tasks - such as Web browsing and e-mail usage - that is exactly why smartphones, tablets, etc - which typically have memory loadouts of that size, or less - are eating PCs for lunch. It's also why I am FAR from surprised over slower sales of larger desktops.)

[snip]

Just out of curiosity, what is your justification for installing XP 64-bit on a PC, especially if it had 2GB or less of RAM?

A 64-bit word takes up twice as much memory as a 32-bit word, so with a small amount of RAM, it's a very very bad idea to go x64.

64-bit simply raises memory limitations, and the benefits on old hardware basically stop there.

I think you're overplaying it a bit. 64 bit applications do consume a little more memory than 32 bit apps but it's certainly not double.

I never said that. The memory for the instructions is double.

A 64-bit word is double that of 32-bit and whether or not you're using all the bits, that memory space is still allocated.

I tried x64 Win 7 on an early Core 2 Duo with 1GB of RAM, and the performance was pretty bad. x86 was better since more memory was freed.

  • 1 month later...

I never said that. The memory for the instructions is double.

A 64-bit word is double that of 32-bit and whether or not you're using all the bits, that memory space is still allocated.

I tried x64 Win 7 on an early Core 2 Duo with 1GB of RAM, and the performance was pretty bad. x86 was better since more memory was freed.

However, the memory USAGE of the application itself is not double - and what was the hardware in question? (One thing that has to be taken into account is badly-written or piggy drivers - while not as large an issue as it used to be, it's still an issue, especially for lower-tier hardware and peripherals.) Given identical loadouts, what's the memory usage comparison between Firefox, PaleMoon x64, and Waterfox? One reason I prefer IntelliPoint Pro (and now the Microsoft Keyboard and Mouse Center driver for Windows 8) to SetPoint for my Logitech V220 is due to SetPoint's piggishness - a porky driver that is less usable compared to an alternative gets replaced by that alternative without a quibble. Love the V220 as a wireless mouse physically, but I loathe the porkiness of SetPoint.

I've run Win 8 on older hardware, as long as the CPU supports it, needing NX bit as I recall, I see no reason to not install it. If you're running under 4GB RAM then I'd personally install the 32bit version but that has alwasy been a personal preference to ensure I'm able to take full advantage of all my system RAM. I've personallay seen a big performance improvement with Windows 8 on older hardware that was previously running XP.

I don't see why it would be a problem. Windows 7 64bit runs awesome on low powered systems, even with aero enabled,

and supposably Windows 8 requires the same specs or lower.

Should work even better than XP anyways, as long as the hardware is compatible.

I'm even thinking of picking up some old piece o junk pc just to try Win 8 on. Wouldn't want to install it on a good computer.

I never said that. The memory for the instructions is double.

A 64-bit word is double that of 32-bit and whether or not you're using all the bits, that memory space is still allocated.

I tried x64 Win 7 on an early Core 2 Duo with 1GB of RAM, and the performance was pretty bad. x86 was better since more memory was freed.

Pointers and such will be double the length, but that's basically it, the actual stuff stored in memory will be about the same.

Edit: And when using 64bit, SSE/2 support is guaranteed, unlike 32bit mode.

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Onkyo Dolby Atmos AV receivers are really solid deals by Sayan Sen Recently we covered great deals on several soundbar models from the likes of Sony, JBL, Samsung and others for really good prices (the lowest in several months). Aside from that we also reported on the Edifier S3000MKII, a hi-fi two-way bookshelf monitor that's available for only $800. Today we bring a list of AV receivers from Onkyo that are available at great prices including the Onkyo NR7100, RZ30, and 8470 (purchase links under the specs table down below). The Onkyo TX-NR7100 and Onkyo TX-RZ30 are both 9.2-channel AV receivers designed for immersive home theater setups but they occupy slightly different tiers within Onkyo’s lineup with the RZ30 positioned as the more advanced model. The TX-NR7100 is a THX Certified 9.2-channel receiver offering up to 100 W per channel (8 ohms, 2 channels driven). It supports Dolby Atmos, DTS:X, and IMAX Enhanced formats, with flexible configurations such as 5.1.4 or 7.1.2 speaker layouts. A key highlight is its built-in Dirac Live Room Correction which should help optimize sound based on your room and its acoustics. In comparison, both models share several core capabilities though the RZ30 is geared toward enthusiasts seeking more precise calibration and system flexibility, while the NR7100 is positioned as a slightly more accessible, value-focused option with strong all-round performance. The technical specs of the RZ30 and NR7100 9.2 AVRs are given in the table below: Specification Onkyo TX-RZ30 Onkyo TX-NR7100 Power Output (FTC, 2ch driven) ~100 W/ch (8Ω, 20Hz–20kHz, 0.08% THD) 100 W/ch (8Ω, 20Hz–20kHz, 0.08% THD) Dynamic / Peak Power 9 × 170 W (6Ω, 1kHz, 1% THD, 1ch driven) 220 W/ch (6Ω, 1kHz, 10% THD, 1ch driven) Frequency Response 5 Hz – 100 kHz (+1/-3 dB) 10 Hz – 100 kHz (+1/-3 dB) THD 0.08% 0.08% Room Correction Dirac Live (full bandwidth) Dirac Live (with AccuReflex support) Immersive Audio Dolby Atmos, DTS:X, IMAX Enhanced Dolby Atmos, DTS:X, IMAX Enhanced Speaker Layout Support Up to 7.2.2 / 5.2.4 / 9.2 processing Up to 7.2.4 / 5.2.4 / 9.2 processing HDMI Inputs / Outputs 6 inputs / 2 outputs (eARC) 6 inputs / 2 outputs (Main + Sub/Zone 2) HDMI 2.1 Support 8K/60, 4K/120, VRR, ALLM, QFT, DSC, eARC 8K/60, 4K/120, VRR, ALLM, QFT, DSC, eARC Video Formats HDR10+, Dolby Vision, HDCP 2.3 HDR10+, Dolby Vision, HDCP 2.3 Streaming / Network Wi-Fi, AirPlay 2, Chromecast, Bluetooth, DTS Play-Fi Wi-Fi, AirPlay 2, Chromecast, Bluetooth, DTS Play-Fi Get them at the links below: Onkyo TX-RZ30 9.2-Channel AV Receiver: $797.00 (Sold and shipped by Electronic Expo) Onkyo TX-NR7100 9.2-Channel AV Receiver: $699.00 (Sold and shipped by Adorma) Onkyo TX-8470 2 Ch Stereo Receiver: $449.00 (Sold and Shipped by Adorma) Good to know This Amazon deal is U.S. specific, and not available in other regions unless specified. We only use first-party seller links or authorized dealer links (at the time of article publishing); ensure that you purchase from such links only. Check out Today's Deals on Amazon | or our recent tech deals. Become a Prime member (for Students or SNAP) via Neowin Get Prime Access - Prime for half price (for qualifying Medicaid, EBT, SNAP) Subscribe to Prime Video, Audible Plus, Music Unlimited or Kindle Unlimited via Neowin As an Amazon Associate, we earn from qualifying purchases.
    • A different thing with Russia. When you say is it better, depends on things. It is better that we don't have the E.U making rules and laws that have nothing to do with them. Is the trading part better? No, that is really mucked up, but then we knew that was going to happen and we would have make agreements, like we do with other parts of the world. Freedom of movement is certainly better, but could be improved, we still need more control over our borders. do you live in the U.K?
    • So what am I quoting from them? I never listened to what Farage or his cronies said. I wanted the U.K to leave the E.u years before the referendum and it had nothing to do with Farage and his cronies. So what country do you live in? Did we work much better together? We were always at logger heads with the E.U because we disagreed with them so much. Maggie was always on at them. I would have thought the E.U was glad to get rid of us as we stopped the integration or made it a two tier. Now without us they can integrate more. I would not have voted out if it was just a trading block and we can still work together on somethings.
    • MPC-BE 1.9.0 by Razvan Serea Media Player Classic - BE is a free and open source audio and video player for Windows. Media Player Classic - BE is based on the original "Media Player Classic" project (Gabest) and "Media Player Classic Home Cinema" project (Casimir666), contains additional features and bug fixes. The BE mod (Black Edition Mod) is a skinned version of Media Player Classic Home Cinema, much better looking than the plain old MPC. MPC-BE 1.9.0 changelog: Splitters Fixed crashes in some situations. AudioSplitter Added support for the RF64 format. Fixed reading of channel layout for some WavPack files. Added support for ID3 tags for Wave64 files. Unknown Wave64 chunks are now ignored. AviSplitter Added support for 'y408' video. Improved support for 'HEVC' video. FLVSplitter Added support for VVC video. MP4Splitter Improved handling of corrupted files. MatroskaSplitter Expanded support for V_UNCOMPRESSED video codecs. Fixed support for frame rotation (ProjectionPoseRoll). Improved support for "V_MS/VFW/FOURCC / HEVC". MpcDvdVideoDecoder Fixed conversion to YUY2. Fixed display of menus for some DVD-Videos. RoQVideoDecoder Output in NV12 and YV12 formats is allowed. Full range is used. MPC Video Decoder RGB32 format will be output as a top-down bitmap by default. Added support for the "IID_MediaSideDataDOVIMetadataV2" interface. Removed support for the deprecated "IID_MediaSideDataDOVIMetadata" interface. Fixed retrieving the name of the video adapter when using NVDEC. Fixed crashes in some situations. MPC Video Converter Added support for AYUV video format. MpcAudioRenderer Improved input format validation. Optimized retrieval of supported formats for exclusive mode. Added the "Keep audio device active when paused" setting. Fixed crashes and freezes in various situations. Subtitles Added the ability to open the properties of an external subtitle renderer in the "Subtitles" settings panel. Fixed external subtitle connections for VSFilter. Fixed a crash when rendering PGS/SUP subtitles when using AVX2. YouTube Improved support for yt-dlp. The built-in YouTube parser is no longer used. Player The HTTP read strategy has been changed. If the playlist contains one entry, more key combinations can be used to control the player (jump through chapters, adjust volume). Improved support for reading ASX playlists. The translation of the MediaInfo report for Chinese, Korean and Japanese has been removed. Added blocking of 32-bit filter "PICVideo Lossless JPEG Decompressor" (pvljpg20.dll), because it crashes. Added blocking of the system filter "AVI Decompressor", which will eliminate the crash of VFW codecs. Fixed a rare crash when using the "/slave" key. Fixed a crash when getting a list of fonts for OSD. Added the ability to load an external audio file using hotkeys. Fixed opening a network path starting with \?\UNC. The "Determine duration when adding" playlist setting now works for YouTube video URLs. The "Online media services" settings panel has been redesigned. Added a "Merge files using FFmpeg" option to the file saving dialog. This option is activated when playing multiple streams obtained using yt-dlp. Added loading of local .dpl playlists ("DAUMPLAYLIST"). Fixed a hang when the user closes the player during the URL opening process. Various interface fixes. Installer Updated MPC Video Renderer 0.10.5. Updated MPC Script Source 0.2.17. Added MPC Image Source 0.3.6. Translations Updated Japanese translation (by tsubasanouta). Updated Chinese (Traditional) and Dutch translation (by beter). Updated Romanian translation (by Andrei Miloiu). Updated Hungarian translation (by mickey). Updated Turkish translation (by cmhrky). Updated German translation (by Klaus1189). Updated Chinese (Simplified) translation (by wushantao). Updated Italian translation (by mapi68). Updated Korean translation (by Hackjjang). Updated Chinese (Traditional) (by udfbe). Updated libraries dav1d 1.5.3-6-g04b69f9; ffmpeg n8.2-dev-1857-g4653e68aab; libpng git-v1.6.55-9-g7d52a8087; Little-CMS git-lcms2.18-26-gf739cda; MediaInfo git-v26.05-38-g702c9b7fd; ZenLib git-v0.4.41-91-g073f297; zlib 1.3.2. Download: MPC-BE 64-bit | Portable MPC-BE 64-bit | ~20.0 MB (Open Source) Download: MPC-BE 32-bit | Portable MPC-BE 32-bit Link: Media Player Classic - BE Home Page Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • Apple reportedly looks to blacklisted Chinese memory chips as RAM prices climb by Karthik Mudaliar Image via Apple Apple is reportedly trying to get a clearance from the Trump administration to buy memory from ChangXin Memory Technologies (CXMT) to get some relief from soaring DRAM prices. As per a report by the Financial Times, Apple approached the Commerce Department more than a month ago and also spoke to other officials and allies in Washington. For starters, CXMT is a company that's already been placed on the Pentagon's list of Chinese military companies. The Chinese company is the country's top DRAM maker. For Apple, the timing is certainly awkward but not surprising. Tim Cook had recently warned that Apple would have to raise prices because AI companies are buying up large amounts of memory for data centers, and just like that, Apple raised MacBook and iPad prices. Micron also recently revealed that customers have committed billions of dollars to secure memory supply years in advance, which shows us how aggressive securing infrastructure has become. This gives suppliers such as Samsung, SK Hynix, and Micron more leverage, while pushing hardware makers to look for alternatives. CXMT is one of those alternatives, but not the simplest one. Apple has spent many years trying to diversify parts of its supply chain away from China, especially for final assembly, while still depending heavily on Chinese manufacturing and suppliers. Even domestic brands from China are moving towards CXMT and YMTC instead of relying on Samsung, Micron, and SK Hynix. For Apple, though, it would invite more scrutiny than local Chinese companies. For now, this is more like a lobbying effort rather than a confirmed supply deal. There's no official statement from either of the parties. What is clearer, though, is the pressure behind such a request. AI demand has certainly made hardware a bottleneck, and companies are trying everything they can to bring things back to normal, even if that means making politically sensitive choices. Source: Financial Times
  • Recent Achievements

    • Week One Done
      flexorcist earned a badge
      Week One Done
    • One Month Later
      Woland13 earned a badge
      One Month Later
    • Week One Done
      Woland13 earned a badge
      Week One Done
    • One Year In
      bernmeister earned a badge
      One Year In
    • Week One Done
      Scoobystu earned a badge
      Week One Done
  • Popular Contributors

    1. 1
      +primortal
      493
    2. 2
      +Edouard
      227
    3. 3
      PsYcHoKiLLa
      148
    4. 4
      Steven P.
      75
    5. 5
      FloatingFatMan
      70
  • Tell a friend

    Love Neowin? Tell a friend!