HDD to SSD clone?

By dcr
in Hardware Hangout

 Share

Recommended Posts

Enthusiast

dcr

Posted
  • Author
Posted

Look up gparted and try that.

Will it switch to the SSD, good question, try it and see (run the TRIM enabled commands). It should do once booted, drivers are installed/reconfigured and you've restarted.

cloning the drive shouldnt be difficult at all as ive done it and i know the tools, im just worried about Windows 7 detecting it correctly. btw, this isnt for me so i cant try it out.

Enthusiast

dcr

Posted
  • Author
Posted

clonezilla?

thats the tool ill use the problem is going from (example) 200GB HDD to 160GB SSD. There are problems as you see in size diffference so I want to make sure that if that 200GB HD partiion is shrinked to 160 (150 just in case) if everything (including boot sector) will work correctly AND that Windows 7 detects it is SSD and turns on its wear tear protection mode.

Grand Master

Jim K Global Moderator

Posted
  • Global Moderator
Posted

I used this guide last year when I installed a SSD into my HTPC. Worked like it should...and easy to follow (probably similar to what Spikey linked to).

http://www.howtogeek.com/97242/how-to-migrate-windows-7-to-a-solid-state-drive/

Enthusiast

dcr

Posted
  • Author
Posted

I have just used Ghost to do a disk to disk image to my new SSD. Worked like a charm. Just make sure that you make the nessecary changes in the BIOS.

clonezilla (dd) is a lot more accurate than ghost.

i know it can be done but i think y ou guys are missing my MAIN questions :)

1: will windows 7 change to ssd mode?

2: will bigger to smaller work?

Grand Master

Jim K Global Moderator

Posted
  • Global Moderator
Posted

clonezilla (dd) is a lot more accurate than ghost.

i know it can be done but i think y ou guys are missing my MAIN questions :)

1: will windows 7 change to ssd mode?

2: will bigger to smaller work?

Did you read the lifehacker or howtogeek article? It answers both of those questions. Short answer is yes

Grand Master

Jason S. Global Moderator

Posted
  • Global Moderator
Posted

i literally just did this a few days ago. I replaced a std hd in my laptop at work w/ an SSD. I used Acronis to make a backup (tlb) of the drive, then restored the image to the SSD. the only downside is that the SSD has much more capacity than the hd so i had unallocated space on the SSD. That can be remedied with software to merge the space or just create another partition.

Grand Master

xendrome

Posted
Posted

I was wondering this myself but What about from 60GB SSD to a 120GB SSD. I currently have 1 GB free right now :( what would I have to tweak in the BIOS in order for it to work properly? I would be using cloneZilla btw

Shouldn't have to "tweak" anything, especially if you are already using an SSD.. Honestly I don't think a BIOS knows the difference between a HDD and SSD, it just see's it as a drive.

Grand Master

Hum

Posted
Posted

thats the tool ill use the problem is going from (example) 200GB HDD to 160GB SSD. There are problems as you see in size diffference so I want to make sure that if that 200GB HD partiion is shrinked to 160 (150 just in case) if everything (including boot sector) will work correctly AND that Windows 7 detects it is SSD and turns on its wear tear protection mode.

Macrium software will adjust the partitions, expand or shrink:

http://kb.macrium.com/KnowledgebaseArticle50081.aspx

Mentor

Radium

Posted
Posted

Why not just create the partitions on the new drive, use XCOPY (command line tool in Windows) and then use BOOTSECT.EXE to write boot sector and use DISKPART (another tool in Windows) to make sure that the correct partition is set as bootable?

I recommend starting from the beginning when moving from one drive to another.

Is the computer UEFI compatible?

Does the current drive use GPT or MBR?

This topic is now closed to further replies.
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Posts

    • Rockstar confirms Grand Theft Auto VI pre-orders begin next week, unveils cover art

      By LoneWolfSL · Posted

      Rockstar confirms Grand Theft Auto VI pre-orders begin next week, unveils cover art by Pulasthi Ariyasinghe The release date of Grand Theft Auto VI has moved quite a lot since its original announcement in 2023, but it finally looks like the game has found its final launch slot. Rockstar today had a new video upload on its YouTube channel, and while it wasn't a new trailer for the game, the company revealed two things. This was the pre-order kickoff date for Grand Theft Auto VI as well as the game's official cover art. The company revealed that June 25 is when fans of the series will be able to pre-order their copy of Grand Theft Auto VI. Pre-orders will be available both digitally and in retail stores. The newly unveiled cover art shows off the two new protagonists, as well as a few more characters that are probably vital to the campaign storyline. Shots of vehicles players can use like a light helicopter, motorcycle, sports car, and speed boat are also seen here, alongside a shot of a crocodile. "Jason and Lucia have always known the deck is stacked against them," says Rockstar describing the campaign's protagonist duo. "But when an easy score goes wrong, they find themselves on the darkest side of the sunniest place in America, in the middle of a conspiracy stretching across the state of Leonida — forced to rely on each other more than ever if they want to make it out alive." Grand Theft Auto VI is coming to Xbox Series X|S and PlayStation 5 on November 19, 2026. A PC version has not been confirmed yet, though it's expected by many to land after the console release. When asked about this, the Take-Two CEO says it considers the core audience for the Grand Theft Auto franchise to be on consoles.
    • The official Funny Pictures thread

      By +primortal · Posted

    • The official Funny Pictures thread

      By +primortal · Posted

    • The official Funny Pictures thread

      By +primortal · Posted

    • How to fix a Secure Boot error on Windows 11: No boot device found.

      By +Warwagon · Posted

      In rare occasions when you turn your computer on you will be greeted with a Secure Boot error followed by the message "No boot device found" If you go into the UEFI and disable Secure Boot the system boots up just fine. Below is a method I found online to fix the issue Disable Secure Boot and boot into Windows (If Bitlocker is enable you'll have to go to https://aka.ms/myrecoverykey on another device to find your bitlocker recovery key). Find a flash drive and make sure it's formatted Fat32 Create a folder on the flash drive called EFI and a subfolder inside EFI called BOOT On your computer navigate to C:\windows\boot\EFI Copy the file SecureBootRecovery.efi to your flash drive\EFI\BOOT Now reboot the computer and tell the computer to boot off that flash drive. You should see a black screen with some text telling you it has repaired Secure Boot Turn Secure Boot back on and reboot and your computer should boot normally.  

  • Recent Achievements

    • Week One Done
      Huge Trailer earned a badge
      Week One Done
    • Week One Done
      Classifyskilleducation earned a badge
      Week One Done
    • One Month Later
      eurospharma62 earned a badge
      One Month Later
    • Week One Done
      With What earned a badge
      Week One Done
    • Week One Done
      Harris Gilbert earned a badge
      Week One Done

  • Popular Contributors

    1. 1
      +primortal
      552
    2. 2
      +Edouard
      169
    3. 3
      PsYcHoKiLLa
      72
    4. 4
      Michael Scrip
      64
    5. 5
      ATLien_0
      64
    Show More

  • Tell a friend

    Love Neowin? Tell a friend!