Play MKV files on Xbox 360 without transcoding


Recommended Posts

Windows 7 has native support for AVCHD which is nothing but H.264/AC3 inside a m2ts container. This means that Windows Media Center can now play these files natively.

Most MKV media that I have seen (personally I have just two MKV files) is H.264 with AC3 audio. So all I needed to do was change the container from mkv to m2ts. Since this method does not need any lossy transcoding, it is far easier and much faster. As long as your source is good, the result is pretty much guaranteed.

Required:

1. A decent spec PC with Windows 7

2. SmartLabs tsMuxer (freeware, no install required)

3. Xbox 360 :p with Media Center extender enabled.

4. MKV media with AVC/H.264 video and AC3 audio

Procedure:

1. Start tsMuxer and add your MKV clip in the input section

post-62693-1238805407_thumb.png

2. In the Tracks section check if you see expected tracks. I included the subtitle track but apparently WMC and WMP don't use it.

3. Did not do anything in the General track options setting

4. In the Output section select M2TS muxing and select desired location.

5. Now hit Start muxing button at the bottom.

post-62693-1238805420_thumb.png

6. Depending on your PC, it will take 5-10mins to perform a pass through conversion of the clip.

7. If all goes well, Windows Explorer will display a thumbnail for this. Try playing it in WMP and check if it plays without problems.

8. Now move the m2ts file to your Video library.

OR

8. Media Center has a special library called "Movie Library" that you can setup from its settings. e.g. e:\Movies. Move the m2ts file to this location.

9. Now give Windows Search enough time to index the new file. For me it was roughly 5mins.

10. Launch WMC from Xbox 360

11. Navigate to either Pictures + Videos>video library or Movies>movie library and play the file.

For me this worked without any problems at the very first attempt. I haven't experimented much with tsMuxer besides whatever I wrote above. This obviously will not work through the dashboard since Xbox 360 doesn't recognize the format (it did not show up in list for me). I am sure they will add the support soon because all consumer HD camcorders use m2ts(or mts) files. PS3 probably supports m2ts format already because of Sony's handycam connection.

Hope this helps people who have Windows 7 installed. I am using build 7057. Although Media Center can be shaky at times so YMMV. :/

yeah but whats the point, you might as well convert it to a format it understands..

cbb until they release native support for most formats..

but nice work doing all this work :)

I don't know when MS will support MKV - probably never, knowing how long it took them to do H.264. Besides this is much better than lossy conversion. IMO anyway.

IIRC it is not possible to stream AC3 5.1 or DTS to the 360 if you remux H264 content.

That's from the creators of MKV2VOB and PS3Media Server.

If you want AC3 5.1 I believe you have to transcode. DTS is just not possible full stop - It only works on the PS3 as the creators of the above applications found a way to trick the PS3 into sending the DTS sound track to your receiver untouched, so your receiver is actually decoding it, not the PS3. It's done by confusing the PS3 into thinking the track is 2 channel PCM, but when it actually reaches your receiver, your receiver knows its DTS and not 2.0 PCM.

If the 360 supported LPCM I believe they may have been able to do the same trick, but the 360 doesn't support HD audio.

People need to understand MKV support on either the 360 or PS3 wouldn't really change anything, it's just a container, codec support is what matters most. Containers can easily be changed.

From 3r1c (MKV2VOB)

There is no way to get x264+ac3 working on xbox 360.

There is 3 ways:

1. convert the ac3 to aac stereo and mux to mp4

2. convert the video to mpeg2+ac3.

3. convert the video+audio to WMV

With transcoding set to always and codec set to xvid, mkv2vob will create xbox360 playable files.

but it converts the video not the audio, this will take much longer then AAC conversion.

But with AAC you will only get stereo, with xvid you get to keep the ac3 5.1

So it's either/or - You can get 5.1 if you transcode video, but if you remux video you get stereo AAC.

Edited by Audioboxer
IIRC it is not possible to stream AC3 5.1 or DTS to the 360 if you remux H264 content.

That's from the creators of MKV2VOB and PS3Media Server.

If you want AC3 5.1 I believe you have to transcode. DTS is just not possible full stop - It only works on the PS3 as the creators of the above applications found a way to trick the PS3 into sending the DTS sound track to your receiver untouched, so your receiver is actually decoding it, not the PS3. It's done by confusing the PS3 into thinking the track is 2 channel PCM, but when it actually reaches your receiver, your receiver knows its DTS and not 2.0 PCM.

If the 360 supported LPCM I believe they may have been able to do the same trick, but the 360 doesn't support HD audio.

People need to understand MKV support on either the 360 or PS3 wouldn't really change anything, it's just a container, codec support is what matters most. Containers can easily be changed.

From 3r1c (MKV2VOB)

So it's either/or - You can get 5.1 if you transcode video, but if you remux video you get stereo AAC.

Media Center is independent of the Xbox dashboard. That's why with Vista you couldn't play Xvid in WMC but you could do it in the dashboard. Windows 7 Media Center now supports AVCHD which is H.264 + AC3. I think I was able to play 5.1. I will check that later today.

Media Center is independent of the Xbox dashboard. That's why with Vista you couldn't play Xvid in WMC but you could do it in the dashboard. Windows 7 Media Center now supports AVCHD which is H.264 + AC3. I think I was able to play 5.1. I will check that later today.

Your own screenshots show it downmixing to two channel AC3. (I think, I've never used either of those programs)

edit: Nevermind, it looks like its just demuxing and muxing it, not downmixing.

Edited by giga
I really wish people would stop using this crap.

This crap?

MKV is an amazing container. Just because you have no use for it doesn't mean thousands of people do.

Most of the *Video* I download is MKV. I would love to simply stream it to my 360 and watch it on my huge plasma.

  • 2 weeks later...
Media Center is independent of the Xbox dashboard. That's why with Vista you couldn't play Xvid in WMC but you could do it in the dashboard. Windows 7 Media Center now supports AVCHD which is H.264 + AC3. I think I was able to play 5.1. I will check that later today.

Mate, u're doing it wrong and don't understand a lot of stuff, let me show u it ... :)

As AB already wrote a lot of interesting stuff, I'm gonna add some stuff to this thread since I own both consoles and know my way around playing mkv on both.

1- The xbox CANNOT play 5.1 AC3 out of the box.

2- The xbox CAN play H264 content up to profile 4.1

3- The xbox CANNOT play files with a DTS track AT ALL ! ( except DVDs and HDDVDs if you still have one )

4- The xbox CAN play H264 files with an AC3 track once the profile is changed ( see n?2) and the AC3 track downsampled to AC3 2.0

5- when playing H264 content, you're limited to 1280*720.

6- The only way to get 1080p files, with 5.1 sound, playing on your xbox is to transcode them to WMV9 or 10.

7- The only software you'll ever need for converting/transcoding stuff on your 360 is GotSent ( A LOT much simpler than mkv2vob if you only got an x360 ).

That's all I remember now:))

P.S. : for all misinformed dudes out there check this link straight from msdn : CLICKY

Is anyone else else have problems playing m2ts and ts files on Xbox via Media Center, I get a slight noticeable stutter when playing these files. The same file but in a mpeg container play fine.

Is anyone else else have problems playing m2ts and ts files on Xbox via Media Center, I get a slight noticeable stutter when playing these files. The same file but in a mpeg container play fine.

I never tried to play a m2ts file with Media Center since the Xbox can already play them via the dashboard

Mate, u're doing it wrong and don't understand a lot of stuff, let me show u it ... :)

As AB already wrote a lot of interesting stuff, I'm gonna add some stuff to this thread since I own both consoles and know my way around playing mkv on both.

1- The xbox CANNOT play 5.1 AC3 out of the box.

2- The xbox CAN play H264 content up to profile 4.1

3- The xbox CANNOT play files with a DTS track AT ALL ! ( except DVDs and HDDVDs if you still have one )

4- The xbox CAN play H264 files with an AC3 track once the profile is changed ( see n?2) and the AC3 track downsampled to AC3 2.0

5- when playing H264 content, you're limited to 1280*720.

6- The only way to get 1080p files, with 5.1 sound, playing on your xbox is to transcode them to WMV9 or 10.

7- The only software you'll ever need for converting/transcoding stuff on your 360 is GotSent ( A LOT much simpler than mkv2vob if you only got an x360 ).

That's all I remember now:))

P.S. : for all misinformed dudes out there check this link straight from msdn : CLICKY

Oh boy, is it too difficult to understand this part?

Media Center is independent of the Xbox dashboard.

If you connect xbox 360 to a Vista media center, it won't even play Xvid/Divx. But with Windows 7 it supports a whole lot of different formats.

Windows 7 has native support for AVCHD which is nothing but H.264/AC3 inside a m2ts container. This means that Windows Media Center can now play these files natively.

Most MKV media that I have seen (personally I have just two MKV files) is H.264 with AC3 audio. So all I needed to do was change the container from mkv to m2ts. Since this method does not need any lossy transcoding, it is far easier and much faster. As long as your source is good, the result is pretty much guaranteed.

Required:

1. A decent spec PC with Windows 7

2. SmartLabs tsMuxer (freeware, no install required)

3. Xbox 360 :p with Media Center extender enabled.

4. MKV media with AVC/H.264 video and AC3 audio

Procedure:

1. Start tsMuxer and add your MKV clip in the input section

post-62693-1238805407_thumb.png

2. In the Tracks section check if you see expected tracks. I included the subtitle track but apparently WMC and WMP don't use it.

3. Did not do anything in the General track options setting

4. In the Output section select M2TS muxing and select desired location.

5. Now hit Start muxing button at the bottom.

post-62693-1238805420_thumb.png

6. Depending on your PC, it will take 5-10mins to perform a pass through conversion of the clip.

7. If all goes well, Windows Explorer will display a thumbnail for this. Try playing it in WMP and check if it plays without problems.

8. Now move the m2ts file to your Video library.

OR

8. Media Center has a special library called "Movie Library" that you can setup from its settings. e.g. e:\Movies. Move the m2ts file to this location.

9. Now give Windows Search enough time to index the new file. For me it was roughly 5mins.

10. Launch WMC from Xbox 360

11. Navigate to either Pictures + Videos>video library or Movies>movie library and play the file.

For me this worked without any problems at the very first attempt. I haven't experimented much with tsMuxer besides whatever I wrote above. This obviously will not work through the dashboard since Xbox 360 doesn't recognize the format (it did not show up in list for me). I am sure they will add the support soon because all consumer HD camcorders use m2ts(or mts) files. PS3 probably supports m2ts format already because of Sony's handycam connection.

Hope this helps people who have Windows 7 installed. I am using build 7057. Although Media Center can be shaky at times so YMMV. :/

what a waste of time, i just installed the codecs ran xbox 360 media center ext, and played the file! Windows 7 build 7000-7077 has allways done this for me!

If you connect xbox 360 to a Vista media center, it won't even play Xvid/Divx. But with Windows 7 it supports a whole lot of different formats.

I don't quite understand how software on your PC can magically change the codec support built into the 360 firmware?

Are you sure Vista Media Center isn't transcoding?

what a waste of time, i just installed the codecs ran xbox 360 media center ext, and played the file! Windows 7 build 7000-7077 has allways done this for me!

Umm, no you did not. MKVs won't be shown in the media center no matter what you do. Although I will be glad if proven wrong. Will save me time. Can you elaborate?

I don't quite understand how software on your PC can magically change the codec support built into the 360 firmware?

Are you sure Vista Media Center isn't transcoding?

I have no idea how media center extenders render video. I am guessing that it doesn't involve the dashboard at all (beyond launching the extender app). For a while other extenders were supporting xvidd, divx and h264 whereas xbox 360 extender (vista) did not. But now with Windows 7, they all work on 360.

Audio, did you ever try running AVCHD(.mts, .m2ts) content on PS3? wikipedia says PS3 supports it natively.

I have no idea how media center extenders render video. I am guessing that it doesn't involve the dashboard at all (beyond launching the extender app). For a while other extenders were supporting xvidd, divx and h264 whereas xbox 360 extender (vista) did not. But now with Windows 7, they all work on 360.

Audio, did you ever try running AVCHD(.mts, .m2ts) content on PS3? wikipedia says PS3 supports it natively.

Yeah I'm just wondering because native video playback either off hard drive or streaming depends on the codecs your console supports, not your PC. The only time PC codecs matter is if you require to transcode a video on your PC first before streaming it.

Also yes, .mts/.m2ts and AVCHD's work on the PS3.

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Indeed. But note that this has Wifi7, HDMI 2.1, BlueTooth 5.4, and 5G Ethernet, so even in the additional features list this bundle blows the Steam Machine away. And, with the money saved, one could improve this dramatically.
    • One of the strangest galaxies in our Universe could help answer some long overdue questions by Sayan Sen Image by Pixabay via Pexels | Not representative An international team of astronomers led by the Department of Astronomy at Tsinghua University has discovered an unusually metal-poor galaxy that may contain signs of first-generation star formation. The galaxy, named Metal-Pristine Galaxy COSMOS Redshift 3 (MPG-CR3), or CR3, was identified using observations from the James Webb Space Telescope (JWST), the Very Large Telescope (VLT), and the Subaru Telescope. The findings, published in The Astrophysical Journal Letters, describe CR3 as the most metal-poor galaxy known from the period known as "cosmic noon," around 11.5 billion years ago. Cosmic noon refers to a period when the universe was producing stars at its highest rate and galaxies were growing rapidly. In astronomy, "metals" refers to all elements heavier than helium, including oxygen, carbon, and iron. Because CR3 contains so few of these heavier elements, researchers say it closely resembles what scientists expect the earliest galaxies in the universe may have looked like. The discovery is significant because it could offer clues about Population III (Pop III) stars, the first generation of stars thought to have formed after the Big Bang. These stars are believed to have formed from gas made almost entirely of hydrogen and helium, before heavier elements were created inside stars and spread across the universe through supernova explosions. Hence this is why CR3 has been referred to as a "living fossil." Scientists have long believed that Population III stars existed only in the very early universe. As more generations of stars formed and died, they enriched surrounding gas with heavier elements, making the conditions needed for metal-free star formation increasingly rare. Because of this, researchers expected the formation of such stars to have largely ended after the epoch of reionization, a period when radiation from the first stars and galaxies transformed the neutral hydrogen filling the universe and made it largely transparent to ultraviolet light. CR3 appears to challenge that idea. The galaxy was observed at a redshift of z = 3.193 ± 0.016. Redshift measures how much light from a distant object has been stretched as the universe expands and helps astronomers determine how far back in time they are looking. In this case, the redshift corresponds to roughly 11.5 billion years ago during cosmic noon. Although the universe was already several billion years old by that point, CR3 shows characteristics more commonly associated with much earlier galaxies. Observations revealed exceptionally strong emissions from hydrogen and helium, including Lyα, Hα, and He I λ10830. Lyα, or Lyman-alpha emission, is a specific wavelength of light produced by hydrogen and is widely used to study distant galaxies. Hα emission is another hydrogen signature commonly used to trace active star formation, while He I λ10830 is produced by helium and can indicate the presence of very hot, young stars. The measured equivalent widths of EW₀(Lyα) = 822 ± 101 Å and EW₀(Hα) = 2814 ± 327 Å are among the highest ever observed in star-forming galaxies. Equivalent width is a measure of the strength of an emission line relative to the surrounding light, and such large values are typically associated with intense and very recent star formation. At the same time, researchers found no statistically significant detections of metal emission lines, including [O III] λλ4959, 5007 and C IV λλ1548, 1550. Emission lines act as chemical fingerprints that reveal which elements are present in a galaxy. Oxygen and carbon lines are commonly seen in galaxies that have already undergone significant chemical enrichment. Their absence in CR3 suggests an unusually pristine environment. Using abundance calibration methods developed with JWST observations, the team placed a 2σ upper limit on the galaxy's gas-phase metallicity of 12+log(O/H)<6.52, corresponding to less than 0.7% of the Sun's metallicity (Z < 7 × 10⁻³ Z⊙). Gas-phase metallicity measures the abundance of heavy elements in a galaxy's gas. A 2σ upper limit indicates that the true value is very unlikely to be higher than the quoted threshold. Even when accounting for uncertainties in the calibration methods, the most conservative limit remains 12+log(O/H)<6.95, making CR3 the most metal-poor galaxy identified at cosmic noon. The galaxy also appears to contain very little dust. Researchers measured a Lyα/Hα flux ratio of 13.9 ± 2.5, a result that suggests negligible dust attenuation, meaning very little of the galaxy's light is being absorbed or scattered by cosmic dust. Because dust is usually produced by earlier generations of stars, this finding further supports the idea that CR3 has experienced very little chemical enrichment. Further analysis using spectral energy distribution modelling, a technique that compares observed light with theoretical models, suggests that CR3 contains an extremely young stellar population only around 2 million years old. The modelling, which used Population III stellar templates, also indicates the galaxy has a stellar mass of approximately 6.1 × 10⁵ M⊙. The symbol M⊙ represents one solar mass, or the mass of the Sun. One of the key questions raised by the discovery is how such a chemically primitive galaxy could exist in a universe that had already spent billions of years producing heavier elements. To investigate this, the researchers examined CR3's surroundings. Their analysis suggests the galaxy may lie in a slightly underdense environment, with a density contrast of roughly δ ≈ −0.12. An underdense region contains less matter and fewer galaxies than average. The team suggests that this relative isolation may have helped preserve pockets of pristine gas. Metal-rich material expelled from nearby galaxies may never have reached CR3, while the lower rate of galaxy mergers and interactions could have slowed the mixing of enriched gas into the system. If future observations confirm these findings, CR3 could provide some of the strongest evidence yet that first-generation star formation continued well after the epoch of reionization. Such a result would challenge the conventional view that pristine star formation ended by z ≳ 6 and suggest that small pockets of metal-free gas survived much longer than previously thought. Researchers stress that more observations will be needed to determine the galaxy's true nature. Future spectroscopic studies with higher resolution and better signal quality could help confirm whether CR3 is genuinely hosting Population III star formation. The discovery is also expected to encourage searches for other similar galaxies, which could help astronomers better understand how the first stars formed and how galaxies evolved in the early universe. Source: Tsinghua University, IOPscience This article was generated with some help from AI and reviewed by an editor. Under Section 107 of the Copyright Act 1976, this material is used for the purpose of news reporting. Fair use is a use permitted by copyright statute that might otherwise be infringing.
    • "I think in the immediate absence of a partner to apply relief" In the words of Sterling Archer... "Phrasing!"
    • For me, the fundamental problems with these "smartglasses" is that they really don't work well for people with significant prescriptions and massively up the price if you use attached lenses if they have displays, and if they don't, then they're not actually "smart" anything, rather just connecting to your phone and relaying voice to an AI. In a few cases like this, they throw in small cameras to feed video to the AI. All around, these feel like both a solution looking for a problem, and the problems it tries to solve seem more easily solved by different approaches and designs. Oddly, if the rumours are true, Apple may actually have invented something for once and it kind of does this right: put cameras in ear buds and manage the interface to AI exactly as most of us do: tapping on an ear bud and saying "Hey Google" or "Hey Siri." That makes them compatible with almost everyone, can double up as a hearing assist device, an impaired vision assist device, a "smart" device... and answer your phone and play music. That just seems like a better solution all around.
  • Recent Achievements

    • Dedicated
      HidekoYamamoto94 earned a badge
      Dedicated
    • One Month Later
      timbobit earned a badge
      One Month Later
    • One Month Later
      nates earned a badge
      One Month Later
    • Week One Done
      Almohandis earned a badge
      Week One Done
    • Rookie
      dorf went up a rank
      Rookie
  • Popular Contributors

    1. 1
      +primortal
      454
    2. 2
      +Edouard
      161
    3. 3
      PsYcHoKiLLa
      107
    4. 4
      Michael Scrip
      84
    5. 5
      Steven P.
      71
  • Tell a friend

    Love Neowin? Tell a friend!