Play MKV files on Xbox 360 without transcoding


Recommended Posts

Windows 7 has native support for AVCHD which is nothing but H.264/AC3 inside a m2ts container. This means that Windows Media Center can now play these files natively.

Most MKV media that I have seen (personally I have just two MKV files) is H.264 with AC3 audio. So all I needed to do was change the container from mkv to m2ts. Since this method does not need any lossy transcoding, it is far easier and much faster. As long as your source is good, the result is pretty much guaranteed.

Required:

1. A decent spec PC with Windows 7

2. SmartLabs tsMuxer (freeware, no install required)

3. Xbox 360 :p with Media Center extender enabled.

4. MKV media with AVC/H.264 video and AC3 audio

Procedure:

1. Start tsMuxer and add your MKV clip in the input section

post-62693-1238805407_thumb.png

2. In the Tracks section check if you see expected tracks. I included the subtitle track but apparently WMC and WMP don't use it.

3. Did not do anything in the General track options setting

4. In the Output section select M2TS muxing and select desired location.

5. Now hit Start muxing button at the bottom.

post-62693-1238805420_thumb.png

6. Depending on your PC, it will take 5-10mins to perform a pass through conversion of the clip.

7. If all goes well, Windows Explorer will display a thumbnail for this. Try playing it in WMP and check if it plays without problems.

8. Now move the m2ts file to your Video library.

OR

8. Media Center has a special library called "Movie Library" that you can setup from its settings. e.g. e:\Movies. Move the m2ts file to this location.

9. Now give Windows Search enough time to index the new file. For me it was roughly 5mins.

10. Launch WMC from Xbox 360

11. Navigate to either Pictures + Videos>video library or Movies>movie library and play the file.

For me this worked without any problems at the very first attempt. I haven't experimented much with tsMuxer besides whatever I wrote above. This obviously will not work through the dashboard since Xbox 360 doesn't recognize the format (it did not show up in list for me). I am sure they will add the support soon because all consumer HD camcorders use m2ts(or mts) files. PS3 probably supports m2ts format already because of Sony's handycam connection.

Hope this helps people who have Windows 7 installed. I am using build 7057. Although Media Center can be shaky at times so YMMV. :/

yeah but whats the point, you might as well convert it to a format it understands..

cbb until they release native support for most formats..

but nice work doing all this work :)

I don't know when MS will support MKV - probably never, knowing how long it took them to do H.264. Besides this is much better than lossy conversion. IMO anyway.

IIRC it is not possible to stream AC3 5.1 or DTS to the 360 if you remux H264 content.

That's from the creators of MKV2VOB and PS3Media Server.

If you want AC3 5.1 I believe you have to transcode. DTS is just not possible full stop - It only works on the PS3 as the creators of the above applications found a way to trick the PS3 into sending the DTS sound track to your receiver untouched, so your receiver is actually decoding it, not the PS3. It's done by confusing the PS3 into thinking the track is 2 channel PCM, but when it actually reaches your receiver, your receiver knows its DTS and not 2.0 PCM.

If the 360 supported LPCM I believe they may have been able to do the same trick, but the 360 doesn't support HD audio.

People need to understand MKV support on either the 360 or PS3 wouldn't really change anything, it's just a container, codec support is what matters most. Containers can easily be changed.

From 3r1c (MKV2VOB)

There is no way to get x264+ac3 working on xbox 360.

There is 3 ways:

1. convert the ac3 to aac stereo and mux to mp4

2. convert the video to mpeg2+ac3.

3. convert the video+audio to WMV

With transcoding set to always and codec set to xvid, mkv2vob will create xbox360 playable files.

but it converts the video not the audio, this will take much longer then AAC conversion.

But with AAC you will only get stereo, with xvid you get to keep the ac3 5.1

So it's either/or - You can get 5.1 if you transcode video, but if you remux video you get stereo AAC.

Edited by Audioboxer
IIRC it is not possible to stream AC3 5.1 or DTS to the 360 if you remux H264 content.

That's from the creators of MKV2VOB and PS3Media Server.

If you want AC3 5.1 I believe you have to transcode. DTS is just not possible full stop - It only works on the PS3 as the creators of the above applications found a way to trick the PS3 into sending the DTS sound track to your receiver untouched, so your receiver is actually decoding it, not the PS3. It's done by confusing the PS3 into thinking the track is 2 channel PCM, but when it actually reaches your receiver, your receiver knows its DTS and not 2.0 PCM.

If the 360 supported LPCM I believe they may have been able to do the same trick, but the 360 doesn't support HD audio.

People need to understand MKV support on either the 360 or PS3 wouldn't really change anything, it's just a container, codec support is what matters most. Containers can easily be changed.

From 3r1c (MKV2VOB)

So it's either/or - You can get 5.1 if you transcode video, but if you remux video you get stereo AAC.

Media Center is independent of the Xbox dashboard. That's why with Vista you couldn't play Xvid in WMC but you could do it in the dashboard. Windows 7 Media Center now supports AVCHD which is H.264 + AC3. I think I was able to play 5.1. I will check that later today.

Media Center is independent of the Xbox dashboard. That's why with Vista you couldn't play Xvid in WMC but you could do it in the dashboard. Windows 7 Media Center now supports AVCHD which is H.264 + AC3. I think I was able to play 5.1. I will check that later today.

Your own screenshots show it downmixing to two channel AC3. (I think, I've never used either of those programs)

edit: Nevermind, it looks like its just demuxing and muxing it, not downmixing.

Edited by giga
I really wish people would stop using this crap.

This crap?

MKV is an amazing container. Just because you have no use for it doesn't mean thousands of people do.

Most of the *Video* I download is MKV. I would love to simply stream it to my 360 and watch it on my huge plasma.

  • 2 weeks later...
Media Center is independent of the Xbox dashboard. That's why with Vista you couldn't play Xvid in WMC but you could do it in the dashboard. Windows 7 Media Center now supports AVCHD which is H.264 + AC3. I think I was able to play 5.1. I will check that later today.

Mate, u're doing it wrong and don't understand a lot of stuff, let me show u it ... :)

As AB already wrote a lot of interesting stuff, I'm gonna add some stuff to this thread since I own both consoles and know my way around playing mkv on both.

1- The xbox CANNOT play 5.1 AC3 out of the box.

2- The xbox CAN play H264 content up to profile 4.1

3- The xbox CANNOT play files with a DTS track AT ALL ! ( except DVDs and HDDVDs if you still have one )

4- The xbox CAN play H264 files with an AC3 track once the profile is changed ( see n?2) and the AC3 track downsampled to AC3 2.0

5- when playing H264 content, you're limited to 1280*720.

6- The only way to get 1080p files, with 5.1 sound, playing on your xbox is to transcode them to WMV9 or 10.

7- The only software you'll ever need for converting/transcoding stuff on your 360 is GotSent ( A LOT much simpler than mkv2vob if you only got an x360 ).

That's all I remember now:))

P.S. : for all misinformed dudes out there check this link straight from msdn : CLICKY

Is anyone else else have problems playing m2ts and ts files on Xbox via Media Center, I get a slight noticeable stutter when playing these files. The same file but in a mpeg container play fine.

Is anyone else else have problems playing m2ts and ts files on Xbox via Media Center, I get a slight noticeable stutter when playing these files. The same file but in a mpeg container play fine.

I never tried to play a m2ts file with Media Center since the Xbox can already play them via the dashboard

Mate, u're doing it wrong and don't understand a lot of stuff, let me show u it ... :)

As AB already wrote a lot of interesting stuff, I'm gonna add some stuff to this thread since I own both consoles and know my way around playing mkv on both.

1- The xbox CANNOT play 5.1 AC3 out of the box.

2- The xbox CAN play H264 content up to profile 4.1

3- The xbox CANNOT play files with a DTS track AT ALL ! ( except DVDs and HDDVDs if you still have one )

4- The xbox CAN play H264 files with an AC3 track once the profile is changed ( see n?2) and the AC3 track downsampled to AC3 2.0

5- when playing H264 content, you're limited to 1280*720.

6- The only way to get 1080p files, with 5.1 sound, playing on your xbox is to transcode them to WMV9 or 10.

7- The only software you'll ever need for converting/transcoding stuff on your 360 is GotSent ( A LOT much simpler than mkv2vob if you only got an x360 ).

That's all I remember now:))

P.S. : for all misinformed dudes out there check this link straight from msdn : CLICKY

Oh boy, is it too difficult to understand this part?

Media Center is independent of the Xbox dashboard.

If you connect xbox 360 to a Vista media center, it won't even play Xvid/Divx. But with Windows 7 it supports a whole lot of different formats.

Windows 7 has native support for AVCHD which is nothing but H.264/AC3 inside a m2ts container. This means that Windows Media Center can now play these files natively.

Most MKV media that I have seen (personally I have just two MKV files) is H.264 with AC3 audio. So all I needed to do was change the container from mkv to m2ts. Since this method does not need any lossy transcoding, it is far easier and much faster. As long as your source is good, the result is pretty much guaranteed.

Required:

1. A decent spec PC with Windows 7

2. SmartLabs tsMuxer (freeware, no install required)

3. Xbox 360 :p with Media Center extender enabled.

4. MKV media with AVC/H.264 video and AC3 audio

Procedure:

1. Start tsMuxer and add your MKV clip in the input section

post-62693-1238805407_thumb.png

2. In the Tracks section check if you see expected tracks. I included the subtitle track but apparently WMC and WMP don't use it.

3. Did not do anything in the General track options setting

4. In the Output section select M2TS muxing and select desired location.

5. Now hit Start muxing button at the bottom.

post-62693-1238805420_thumb.png

6. Depending on your PC, it will take 5-10mins to perform a pass through conversion of the clip.

7. If all goes well, Windows Explorer will display a thumbnail for this. Try playing it in WMP and check if it plays without problems.

8. Now move the m2ts file to your Video library.

OR

8. Media Center has a special library called "Movie Library" that you can setup from its settings. e.g. e:\Movies. Move the m2ts file to this location.

9. Now give Windows Search enough time to index the new file. For me it was roughly 5mins.

10. Launch WMC from Xbox 360

11. Navigate to either Pictures + Videos>video library or Movies>movie library and play the file.

For me this worked without any problems at the very first attempt. I haven't experimented much with tsMuxer besides whatever I wrote above. This obviously will not work through the dashboard since Xbox 360 doesn't recognize the format (it did not show up in list for me). I am sure they will add the support soon because all consumer HD camcorders use m2ts(or mts) files. PS3 probably supports m2ts format already because of Sony's handycam connection.

Hope this helps people who have Windows 7 installed. I am using build 7057. Although Media Center can be shaky at times so YMMV. :/

what a waste of time, i just installed the codecs ran xbox 360 media center ext, and played the file! Windows 7 build 7000-7077 has allways done this for me!

If you connect xbox 360 to a Vista media center, it won't even play Xvid/Divx. But with Windows 7 it supports a whole lot of different formats.

I don't quite understand how software on your PC can magically change the codec support built into the 360 firmware?

Are you sure Vista Media Center isn't transcoding?

what a waste of time, i just installed the codecs ran xbox 360 media center ext, and played the file! Windows 7 build 7000-7077 has allways done this for me!

Umm, no you did not. MKVs won't be shown in the media center no matter what you do. Although I will be glad if proven wrong. Will save me time. Can you elaborate?

I don't quite understand how software on your PC can magically change the codec support built into the 360 firmware?

Are you sure Vista Media Center isn't transcoding?

I have no idea how media center extenders render video. I am guessing that it doesn't involve the dashboard at all (beyond launching the extender app). For a while other extenders were supporting xvidd, divx and h264 whereas xbox 360 extender (vista) did not. But now with Windows 7, they all work on 360.

Audio, did you ever try running AVCHD(.mts, .m2ts) content on PS3? wikipedia says PS3 supports it natively.

I have no idea how media center extenders render video. I am guessing that it doesn't involve the dashboard at all (beyond launching the extender app). For a while other extenders were supporting xvidd, divx and h264 whereas xbox 360 extender (vista) did not. But now with Windows 7, they all work on 360.

Audio, did you ever try running AVCHD(.mts, .m2ts) content on PS3? wikipedia says PS3 supports it natively.

Yeah I'm just wondering because native video playback either off hard drive or streaming depends on the codecs your console supports, not your PC. The only time PC codecs matter is if you require to transcode a video on your PC first before streaming it.

Also yes, .mts/.m2ts and AVCHD's work on the PS3.

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Micron reveals AI companies are spending billions to lock up its memory years in advance by Karthik Mudaliar The demand for more memory is far from over, and Micron is turning the AI-driven memory shortage into a much more predictable business. The company has revealed that it has signed 16 strategic supply agreements backed by roughly $22 billion in customer deposits and other financial commitments. The contracts cover DRAM and NAND deliveries over several years, with some running through 2030. With the AI boom, demand for high-bandwidth memory (HBM) has grown so quickly that large customers are now prepared to help finance future production in exchange for a guaranteed supply. According to Micron’s latest financial results, the company received commitments worth about $22 billion across its new agreements. Around $18 billion is expected to arrive as cash deposits, while the rest will come through other financial arrangements. Micron says the agreements could generate approximately $100 billion in future contracted obligations. They cover around 20% of its expected DRAM shipments and one-third of its NAND shipments during their respective terms. It should be noted that although AI infrastructure is the main force behind the current shortage, not all 16 agreements with Micron involve AI companies. Micron said the customers also include consumer electronics and automotive businesses, two sectors that increasingly compete with data centers for the same manufacturing capacity. HBM is consuming an increasing share of that supply. Unlike conventional desktop or server RAM, HBM stacks multiple memory dies vertically and places them close to an AI accelerator. This gives GPUs and other AI chips access to data at much higher speeds, but it also requires more complicated manufacturing and packaging. Micron says its 12-layer HBM4 memory is now shipping in high volume for a lead customer, with samples also supplied to other companies. The chipmaker has already generated more than $1 billion in HBM4 revenue and says the product is ramping twice as quickly as its earlier HBM3E generation. Samsung has similarly warned that the memory shortage could continue into 2027 and beyond. Consumer memory companies have also had to address sharp increases in DDR5 pricing, suggesting the effects are already reaching beyond the data center. For consumers, that could mean the AI memory crunch lasts longer than expected, even as manufacturers invest heavily in new production.
    • XnConvert 1.112 by Razvan Serea  XnConvert is a cross-platform batch image-converter and resizer with a powerful and ease of use experience. All common picture and graphics formats are supported (i.e. JPG, PNG, TIFF, GIF, Camera RAW, JPEG2000, WebP, OpenEXR) as well as supporting over 500 other image formats. Also available within the batch operations include rotating, adding of watermarks, adding of text along with many image-adjustment features such as brightness, shadows and more. Among the features included are: Batch adding of files and folders Support for drag and drop of files Batch rotating, cropping, resizing and more Adding of photo masks Preserving or removing image metadata in conversions Multipage image file support (i.e animated GIF, APNG, TIFF) Command line integration via NConvert Filters - such as 'Blur', 'Gaussian Blur', 'Emboss', "Sharpen' and much more Effects - such as 'Old camera' and much more Download: XnConvert 64-bit | Standalone | ~30.0 MB (Freeware) Download: XnConvert 32-bit | Standalone Links: XnConvert Website | Screenshot | Release Announcement Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • Microsoft updates Visual Studio Code with chat cost tracking and multi-agent chats by Paul Hill Microsoft has just launched Visual Studio Code 1.126, its latest weekly release. This time, the company has focused on letting you see the total cost of chat sessions to spot expensive conversations; enabling multiple chats per session that run side-by-side in one agent host Copilot session; and letting you browse new folders safely in restricted mode. We have now reached the stage where free AI in IDEs is coming to an end. To help you keep track of your costs, VS Code now lets you see the entire cost of a chat session, rather than just individual turns. This should give you more transparency about which sessions consume the most credits, so you can better manage your usage over time and spend less. For those of you using the Agents window, you know it is possible to run and manage multiple agent sessions at once. In this update, a Copilot session started from an agent host can hold several chats at once. Explaining how this feature works, Microsoft writes: Finally, from this update forward, Microsoft will remove the pop-up when opening an untrusted folder. When you open a new folder now, it will automatically open in Restricted Mode. You will see a banner that lets you manage the trust level of the folder. Microsoft has made this change so that it’s easier to start inspecting code without giving it trust right away. If you have VS Code, you can check for updates within the app now to get this new version. Otherwise, you can download it from the Visual Studio Code website.
    • Anthropic accuses Alibaba of using 25,000 fake accounts to copy Claude's capabilities by Karthik Mudaliar Anthropic has accused Alibaba of using nearly 25,000 fraudulent accounts to extract capabilities from Claude on a huge scale. According to a report from Reuters, Anthropic told US lawmakers that operators linked to Alibaba and the company’s Qwen AI team generated 28.8 million exchanges with Claude between April 22 and June 5, 2026. That is a lot of Claude conversations, but Anthropic says this was not ordinary chatbot use. The company believes the accounts were part of a coordinated effort to collect answers that could help train or improve rival AI systems. The alleged campaign reportedly focused on some of Claude’s most valuable skills, including software development, multi-step reasoning, and agentic tasks. In practical terms, that means getting an AI model to plan and complete work across several stages rather than simply answering a single question. This is called 'distillation,' where AI companies use outputs from a larger model to train a smaller and cheaper one. The smaller model learns to imitate useful parts of the more capable system without needing the same amount of computing power. The distillation process isn't automatically suspicious, but the problem comes when one company gathers another provider's outputs without permission and at an industrial scale. Also, this does not mean Alibaba obtained Claude’s source code, model weights, or original training data. Instead, Anthropic claims the accounts repeatedly asked Claude carefully designed questions and collected the answers. Those answers could then be used as training material for another model. Anthropic has made similar accusations against DeepSeek, Moonshot AI, and MiniMax earlier this year. As Neowin previously reported, Anthropic said those three companies collectively generated more than 16 million Claude exchanges through roughly 24,000 accounts. Anthropic says the new campaign produced almost twice as many exchanges in a matter of weeks. Anthropic reportedly told lawmakers that the campaign could help Chinese AI developers approach the capabilities of its Mythos Preview model. Mythos is focused on advanced cybersecurity work, including finding and exploiting complex software vulnerabilities. via Reuters | Photo via DepositPhotos.com
  • Recent Achievements

    • Rookie
      krychek57 went up a rank
      Rookie
    • Grand Master
      Jaybonaut went up a rank
      Grand Master
    • One Year In
      Philsl earned a badge
      One Year In
    • Dedicated
      Scoobystu earned a badge
      Dedicated
    • First Post
      Tom Schmidt earned a badge
      First Post
  • Popular Contributors

    1. 1
      +primortal
      441
    2. 2
      +Edouard
      175
    3. 3
      PsYcHoKiLLa
      134
    4. 4
      Michael Scrip
      79
    5. 5
      Xenon
      77
  • Tell a friend

    Love Neowin? Tell a friend!