iPhone 4 is running hot and battery draining faster than normal


Recommended Posts

I've noticed all day today that my iPhone 4 has been a little warm (especially right above the "iPhone" labeling on the back). It was down to 50% at lunch and a co-worker suggested that it may be the location service, so I turned that off.

At 4 pm it was at about 20% and I was getting the low battery warning. It was 100% full when I left this morning, and under normal usage I'm around 60-75% full when I go to sleep at night. I can normally go 2 days without charging so I know something is up.

I'm doing a full DFU restore now. Hope this isn't a hardware problem. The device itself is working fine from what I can tell. The heat is evident and the power usage is evident.

I'm hoping its some strange software fluke and a full restore fixes it...

Surely sounds like heavy battery drain, which causes the heat.

Is that iPhone jailbroken and which iOS version does it run?

In case it's jailbroken, what do you have installed?

Glassed Silver:mac

It isn't Jailbroken. iOS 5.0.1 was on it and currently be reinstalled.

The only things I can think of that may be related (or completely coincidental) are:

* I cleaned some pocket lent out of the bottom port with a pocket knife blade yesterday... the connector looks fine, visually, and isn't otherwise having problems.

* Yesterday I was around the border and my phone kept connecting to a Mexico cell tower. And it was like...stuck on that damn tower even when I was quite a ways away and should have been well within range of a state side AT&T tower. I kept my phone off hoping to avoid roaming data charges (I suspect I'll be calling AT&T on that one). It was peculiar all the same. Kept connecting to "movistar". Maybe my phone got hacked by a drug cartel.

It isn't Jailbroken. iOS 5.0.1 was on it and currently be reinstalled.

The only things I can think of that may be related (or completely coincidental) are:

* I cleaned some pocket lent out of the bottom port with a pocket knife blade yesterday... the connector looks fine, visually, and isn't otherwise having problems.

* Yesterday I was around the border and my phone kept connecting to a Mexico cell tower. And it was like...stuck on that damn tower even when I was quite a ways away and should have been well within range of a state side AT&T tower. I kept my phone off hoping to avoid roaming data charges (I suspect I'll be calling AT&T on that one). It was peculiar all the same. Kept connecting to "movistar". Maybe my phone got hacked by a drug cartel.

LOL, adored the last part! :p

Either way, in future, why not just switch off Roaming? :)

Well, I guess a Restore is your best bet atm, keep us updated! (Y)

Glassed Silver:mac

Usually a restart is enough to cure such issues. It's normally some program not allowing the CPU to sleep that causes the heat which therefore kills the battery. A restart kills that app/service.

I'm really scratching my head on this one. The device felt cool last night after I had restored the OS and a backup. It seemed OK for most of the morning. Picked it up about an hour ago and it felt warmmer than usual. It still feels warmer than usual and my battery is down to 46%. Comparitively I have a co-worker with an iPhone 4 and his phone is at 97% and feels cold compared to mine.

I did a test. In 11 minutes with the problem my batter when dropped 3% (43% to 40%). I turned on "Airplane Mode" on my phone and the device feels much cooler and after about 20 minutes the battery life hasn't dropped at all (still at 40%). Something is going on in the background that is causing this drain. Hmmm...

tried cleaning the sim card yet?

No, I haven't tried that. I will try that, but don't really understand what that will accomplish. The phone connects to AT&T just fine, anyway.

I did another test over lunch. I reset the cell data usage statistics and after about 5 minutes it had used 10MB total (6 down, 4 up). Something on the phone is sucking data. I turned off cell data and WiFi, and the phone cools back down and no dramatic battery life drain was observed. I just went through and disabled every notification service except for Phone and Messaging and have cell data on and WiFi off. I'm going to check in about 10 minutes to see if it is still leaking.

tried killing all the running apps in the taskbar?

Yes. I turned off all the notification services as well except for Phone and Messages. Disabled all the syncing services (Mail, Calendar etc). I'm now deleting apps. I've deleted some apps and it is still using cell data for some reason.

While maybe unlikely, it could be a hardware problem as well. Maybe you can exchange it for a new one at the store?

I'm starting to think that maybe it is hardware related. Unfortunately, the phone is no longer under warranty.

I've now deleted every single non-stock app off the phone. Everything is turned off except cell data. Every iCloud feature. Every sync service.

I'm still observing about 1 KB/sec of cell data usage but the device feels cooler now. I'm going to give it about 30 mins and see what the data usage looks like.

Settings > Location Services > System Services

Check that Diagnostics & Usage, Location-Based iAds, and Setting Time Zone are off. I've heard of people having issues with those services checking in way more often than they need to.

My friend who has iPhone 4, also had a simlar problem when he updated his iOS to 5.0. He finally figured out that the problem was in MS Exchange. After the upgrade, the Exchange would cause rapid battery drainage. But after resetting MS Exchange (I don't know what he did), the battery consumption went back to normal.

My friend who has iPhone 4, also had a simlar problem when he updated his iOS to 5.0. He finally figured out that the problem was in MS Exchange. After the upgrade, the Exchange would cause rapid battery drainage. But after resetting MS Exchange (I don't know what he did), the battery consumption went back to normal.

Thanks for that info! My work's email is an exchange server and I've noticed some weird behavior in the past few days where it once or twice a day a message will pop-up about unable to verify the authenticy of my works server. Our secure connection isn't verisigned or whatever, so we just click through that stuff. Usually I just have to do it once, but it has bugged me at least once a day.

As I went through and deleted everything on my phone I think I found the culpret of the problem (but am not 100% sure). I recently downloaded PC Gamer magazine on my iPad and subscribed to that. The app was loaded onto my phone during a sync with my computer a few nights ago. I found that in the "Store" settings, PC Gamer was set to auto download new content and to use Cell Network. I think this may have been the problem, but I don't understand why it wouldn't just download the latest issue over WiFi and be done with it (what is with the trickle download over WiFi and Cell?).

Anyway, nuked everything not pre-loaded on the OS and I've re-enabled all my sync services. After about an hour the battery life seems fine (hasn't dropped 1%) and the device feels cool. I'm going to slowly add things back on as I need them. I'm going to have to leave my Cell Data turned off until the end of my month period because I'm only on the 200MB plan and this problem has sucked up about 170MB over the past 2 days :( :(.

I'm probably still not out of the woods. I hate having the battery % shown at the top because I find myself just staring at it and thinking about it, but I'll probably leave it there for the next few days... I hope it was just the PC Gamer magazine trying to download the latest edition or something. It would give me some peace of mind that it was a setting or something rather than just a bug somewhere.

So today everything has worked just fine. No heat noticed, and it is almost the end of the work day and my phone is at 86% which is back to normal. So at least I'm certain that there isn't any underlying hardware issues.

I'm uncertaint what exactly was the problem, but I'm incline to believe that it had to do with Exchange as Aletheia suggested. Reason being, I had a significant amount of upload data as well as download data shown in the usage under cell data. I thought that maybe it was the PC Gamer magazine trying to download the latest issue, but then it would be all downstream activity and no upstream activity. My upstream and downstream data was about the same, which in my mind is more consistent with a problem talking with something like Exchange.

&*^#$(&)*UJG*$@

This is really starting to get irritating. So I've had cell phone data turned off because the problem had sucked up most of my monthly data and now I have about 15MB to work with over the next 9 days or else I'll be charged another $15. I momentarily turned on the Cell Data at lunch to check a website, and I started to notice the same thing happening. My phone began to heat up and the data usage was going wild on the cell data side. Blah. Looks like the problem is not solved yet.

While ONLY connected to WiFi and with the Cell Data turned OFF there doesn't seem to be any problems. Connected to WiFi and with Cell Data turned ON, my phone starts to heat up and the cell data is going crazy. Just sitting here for 3 minutes, my phone uploaded 500KB and downloaded about 700KB through the Cell network even though WiFi is connected and enabled! :cry:

You should just take it into the Apple store and see what they think. Even though it's out of warranty, it's not uncommon that they will give you a replacement at no cost. It's worth a shot instead of being burdened by it. :)

  • Like 1

I think it is probably worth taking to Apple.

I deleted all of my email accounts and my iCloud account off of my phone. Went to check usage and it seemed to have stopped. I re-enabled all my email accounts and my iCloud account, went to usage (re-set the statistics) and it used about 20KB down and 8KB up and then stopped... I checked it in 5 minutes and it hadn't sent or received any data through the cell network.

I dunno if this actually fixed things or my deleting and re-enabling the accounts was just coincidental to another intermittent problem.

I think it is probably worth taking to Apple.

I deleted all of my email accounts and my iCloud account off of my phone. Went to check usage and it seemed to have stopped. I re-enabled all my email accounts and my iCloud account, went to usage (re-set the statistics) and it used about 20KB down and 8KB up and then stopped... I checked it in 5 minutes and it hadn't sent or received any data through the cell network.

I dunno if this actually fixed things or my deleting and re-enabling the accounts was just coincidental to another intermittent problem.

Ask the Apple Store to give you something to hand your mobile carrier so you might get some of the data back and not have a month of no mobile data! :)

Glassed Silver:mac

It will have to wait until I have an opportunity to travel to the city near by (about an hour) to get to an Apple store. If the symptoms come back again I'll take it to the AT&T store. If anything I can document that i took it there if I have any charges on my bill I need to dispute. I think I have enough data to get me through the rest of the month though.... it will suck :(.

Worst case scenario I can use my old iPhone 3gs until my contract runs out in June.

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • If Valve refused to let them make the case, I wonder if they've already partnered with someone else to do it? The fact that they didn't seek permission/licence before diving straight in is incredible though
    • OpenClaw now has native mobile apps on iOS and Android by Karthik Mudaliar OpenClaw, the viral open-source personal AI agent, now has its own mobile app, available on both Android and iOS. Users can pair the app with an existing OpenClaw gateway and can start using new mobile-native features that are now available on the app. The app supports all the existing features you'd already have seen on OpenClaw's TUI, as well as some more, such as real-time and background Talk mode, action approvals, sharing from iOS, and optional access to device capabilities such as camera, screen, location, photos, contacts, calendar, and reminders. These features are available on both the Android and iOS versions of the app. What's important with these apps is that they don't run OpenClaw on your phone, but are actually just companion apps that require a running OpenClaw Gateway on an existing device, on macOS, Linux, or Windows via WSL2. To pair the app with your existing OpenClaw gateway, users need to run the command "/pair qr" on the TUI or existing chat interface, which brings up a QR code. Users can then scan this QR code to pair it up with the mobile app. There's also an option to manually pair the app by entering the host and a port. Previously, OpenClaw had been available on phones via WhatsApp, Telegram, Slack, Discord, Microsoft Teams, Matrix, and others. Now, with a native mobile app, the interface is much cleaner and more focused on just the OpenClaw, of course, with the added support for camera, screen, location, and more. It's important to note that OpenClaw comes with its own security warnings. There's always a chance of prompt injection with these tools, so users are recommended to double-check authentication, tool policy, sandboxing, and execution approvals rather than prompts alone. For users well-versed with the AI harness, a native mobile app makes it easier to approve an automation, share a link, use voice, or let an agent react to phone-side context.
    • Google pitches Spanner as one database for all AI agents with these new featues by Karthik Mudaliar Google Cloud is introducing new features within Spanner, its distributed database, as a place where enterprises should keep their data, using which AI agents could make smarter and better decisions. In a detailed blog post, Google highlighted quite a few features coming to Spanner, including relational data, graph relationships, vector search, key-value access, full-text search, and operational analytics together in one database architecture. Google says that today's systems aren't well-made for AI agents. There could be data that is present in one system, search indexes in another, embeddings in a vector database, and relationship data in a graph database. This fragmentation isn't great for AI agents to do their jobs because they don't have access to all of this data in one place. This is where Google is positioning Spanner as a solution. Spanner is already a globally distributed relational database with strong consistency, and Google wants its customers to see it as a broader data layer for AI applications. The company introduced something called Spanner Graph, along with integrated vector search, full-text search, a Cassandra-compatible key-value endpoint, and a columnar engine for analytical queries on operational data. Google also added that its ScaNN-powered vector search can support indexes with more than 10 billion vectors, while the columnar engine can make some analytical scans up to 200 times faster. All of this isn't just exclusive to the Google Cloud Platform, and there's support for multi-cloud as well. This comes via Spanner Omni, which Google says is a downloadable, containerized version of Spanner that can run on Kubernetes and in environments outside Google Cloud, including Microsoft Azure and AWS, and even on-premises infrastructure as well as edge deployments. Google says that customers who are interested in the full-featured edition should contact the company, and there's no word on commercial availability or separate pricing. Those interested can read the full blog by Google Cloud, which details these features individually.
    • Kalmuri 4.2.5 by Razvan Serea Kalmuri is your all-in-one, portable screen capture and recording solution designed for speed, simplicity, and flexibility. Whether you need a full-screen snapshot, a custom area, a scrolling webpage, or smooth video recording, Kalmuri delivers with ease. Capture text instantly from images with built-in OCR, keep floating images on top for quick reference, and use the precise color picker for perfect design matching. Customize hotkeys to work your way and share results instantly with built-in upload options. Kalmuri runs without installation, making it ideal for USB use, and offers an intuitive interface that’s easy to learn. Kalmuri key features: Video recording support (designation of whole screen and area) Whole screen, active program, window control, area application Extract text from images using optical character recognition (OCR). Support for PNG, JPG, WEBP, BMP, GIF file formats MP4 video recording powered by FFmpeg for high-quality results Full web page capture Share the captured image on the web Color extraction function Printer output Hotkey settings Adjustable via keyboard for area capture (Arrow key, Ctrl+Arrow key, Shift+Arrow key) File name format (sequential, datetime) Free to use it at work, at home, in government offices, at school, etc. Using Kalmuri portable for video recording Kalmuri’s portable version doesn’t include FFmpeg, which is required for video recording. Without it, you’ll get an “error FFmpeg.exe not found” message. To fix this, download FFmpeg from the provided link, extract it, and place FFmpeg.exe in Kalmuri’s folder. Kalmuri will then recognize it automatically, allowing you to start recording in high quality instantly. Kalmuri 4.2.5 changelog: Fixed an intermittent crash when using Area Capture Improved stability for Area Capture and screen recording Resolved a capture issue that could occur right after startup Download: Kalmuri 4.2.5 | 24.2 MB (Freeware) Download: Kalmuri Portable 4.2.5 | 2.1 MB View: Kalmuri Website | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
  • Recent Achievements

    • First Post
      rosiecharles earned a badge
      First Post
    • Reacting Well
      Juan Dela earned a badge
      Reacting Well
    • Week One Done
      Collagen Project earned a badge
      Week One Done
    • Reacting Well
      Wakeen1966 earned a badge
      Reacting Well
    • Rookie
      Almohandis went up a rank
      Rookie
  • Popular Contributors

    1. 1
      +primortal
      516
    2. 2
      +Edouard
      273
    3. 3
      PsYcHoKiLLa
      143
    4. 4
      Steven P.
      98
    5. 5
      macoman
      54
  • Tell a friend

    Love Neowin? Tell a friend!