[2008 iMac] Not booting from OSX CD


Recommended Posts

I've got a mid 2008 24'' iMac. Its served me well up until two days ago. It refuses to boot into OSX. Windows bootcamp boots perfectly.

No problem, I think, I'll just re-install and restore from my Time Capsule. Go to boot from my OSX SL Retails DVD. Kernel panics. Dig out the DVD that came with the iMac, same. No dice. Just Kernel Panics.

I'm able to boot into windows fine, however. I can also boot other CDs perfectly fine (gparted, memtest). I figure its a HDD issue, so I load up GParted and nuke the drive. Still, no dice. Kernel panics.

Bad RAM maybe? I remove the sticks and try them both in both slots one at a time. Still, no dice. OSX SL DVD just Kernel panics.

Any tips, ideas or suggestions?

Link to comment
https://www.neowin.net/forum/topic/1076569-2008-imac-not-booting-from-osx-cd/
Share on other sites

When you boot off the SL DVD, does it Kernel Panic before it gets to the point of writing to the HDD? See if the SL DVD boots even with no Hard Drive installed? Ran the AHT Apple Hardware Test? Reset the NVRAM and SMC?

If it is not an I/O issue causing the panics (eg: HDD) it seems odd that both Memory modules would have the problem, so if the HDD & RAM are OK, maybe it is something less replacement friendly (Logic Board/Northbridge/CPU).

I assume that you have removed all USB devices except the keyboard to rule this out also. The fact that Windows and other boot discs are working I would not read too much into, sometimes these types of issues have a bit of a random factor to what symptoms you end up with.

When you boot off the SL DVD, does it Kernel Panic before it gets to the point of writing to the HDD? See if the SL DVD boots even with no Hard Drive installed? Ran the AHT Apple Hardware Test? Reset the NVRAM and SMC?

If it is not an I/O issue causing the panics (eg: HDD) it seems odd that both Memory modules would have the problem, so if the HDD & RAM are OK, maybe it is something less replacement friendly (Logic Board/Northbridge/CPU).

I assume that you have removed all USB devices except the keyboard to rule this out also. The fact that Windows and other boot discs are working I would not read too much into, sometimes these types of issues have a bit of a random factor to what symptoms you end up with.

thanks for a nice detailed post!

I boot from the DVD, I get the spinner under the Apple logo - thats where it Kernal Panics. It reads from the CD for a good few minutes and then goes.

I ran the AHT by holding the D key with the Leopard disk in the drive, and it freaked out. Oranges flashes and garbled pixels - not a good sign I'm sure.

I've reset the NVRAM - Not heard of SMC but after looking it up I've accidentally followed that procedure so we can rule that out.

I've nuked the HDD now with the same issues, so im not sure thats the issue but I'm trying to avoid taking out the HDD - seems i might have to give that a bash though.

I've also removed all USB devices and tried different USB ports on the back.

No joy I fear :(

Well try one RAM stick at a time.

If still no good try with another compatible RAM stick completely.

If still no good try one RAM stick and no HDD.

It also occured to me that it could be the Superdrive itself. Use a working Mac to copy the SL DVD to an 8GB+ USB Stick t(Google it for a guide to make sure you do it right so that it is bootable, it is quite easy to do) and see if it boots from a USB, even physically disconnecting/removing the Superdrive if possible (since you would need to go in to take out the HDD anyway)

If that doesn't work then something on your Logic Board is stuffed. Doesn't matter if it's the Northbridge/CPU/GPU etc. because it is all integrated anyway. You'ld either have to find a replacement Logic Board (i.e. eBay) or buy a new Mac and sell the parts you have left on eBay.

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • This looks awesome, I will request access via Steam later this afternoon!
    • Personally, I’ve found that it’s usually worth investing in the infrastructure you don’t want to replace later, especially cabling. Running Cat6A (or better, depending on your needs) during an upgrade is relatively inexpensive compared to having to re-cable a few years down the road. For switches I try to balance current specs with realistic growth. If my budget allows it Ill choose switches with higher uplink speeds which leaves room for expanding later on, but I don’t necessarily overspend on access ports if the endpoints won’t benefit from them anytime soon. One lesson I’ve learned is that planning for scalability pays off. It’s much easier to add devices, VLANs, or higher-bandwidth workloads when your network infrastructure already supports it than to replace hardware later.  What is your budget like?
    • I hate the term, "future-proof." We saw it back in the 90's / 2000's, if not before. You cannot future-proof anything, since there is no definition of how far into the future you plan on prepping for. Best idea is to tell us what you currently have and what its use is at the moment, and we can then offer ideas about some areas that might need an upgrade and other areas that can be left alone.
    • I can agree that it is being used in a small capacity. I worked for a company where their engineers still used XP, and when asked why it was because their sensor software wasn't compatible with newer operating systems and the software was discontinued so they couldn't upgrade the software. Given that the sensors were still in use by companies, they had to continue using XP to support the sensor, otherwise the price to the company would have gone into the millions or billions. Our response was simple: Ok, you can keep the XP machine. But we're removing it from the network. "But then it can't access the Internet or folder shares!" Yup, kinda the point. If someone wants to continue using an unsecure OS they can do, I have no problem with that. But it should be isolated. Simple. I had a fight with a guy in the engineering department for weeks before he finally relented. But we digress.   What do I plan on doing to commemorate the anniversary? Nothing. I have fond memories of the OS, but at the end of the day it's just an OS. If I had some time I might see if I could install it on my Raspberry Pi for a laugh. But my reflex memory with today's OS ideas would probably get me frustrated and I'd uninstall it after 5 mins.
    • Shutter Encoder 20.2 by Razvan Serea Shutter Encoder is one of the best video converter software and image, audio available today. It has been designed by video editors in order to be as accessible and efficient as possible. It is one of the few free professional tools. Based on FFmpeg, it has the largest codec library available. You can thus convert your files into many different formats. Complete settings for the most advanced Shutter Encoder has a panel containing a large number of settings, in order to define your own choices based on your files and perfect your video or audio output. Well-thought-out settings, with parameters predefined to create files quickly and easily. List of functions Without conversion: Cut without re-encoding, Replace audio, Rewrap, Conform, Merge, Extract, Subtitling, Video inserts Sound conversions: WAV, AIFF, FLAC, MP3, AAC, AC3, OPUS, OGG Editing codecs: DNxHD, DNxHR, Apple ProRes, QT Animation, GoPro CineForm, Uncompressed YUV Output codecs: H.264, H.265, VP9, AV1, OGV Broadcast codecs XDCAM HD422, AVC-Intra 100, XAVC, HAP....and much more. Shutter Encoder 20.2 changelog: Added "Intel Quick Sync" hardware acceleration for Linux Added 'Identify speakers' option for "Audio transcription" function Improved installer package Improved video player performance Improved timecode display with drop-frame videos Improved naming convention for surround audio files Fixed splash screen freeze Fixed bug with file hanging Fixed bugs with presets loading Fixed bugs with video player's buffer Fixed bug with 'Total length of file' option Fixed bugs with 'Record screen/device' option Fixed bug with "XAVC" & "XAVC Long GOP" functions Rollback to XPDF tool for PDF conversion Removed unused binary architecture for Mac Various corrections Various improvements Download: Shutter Encoder 20.2 | 166.0 MB (Open Source) Download: Shutter Encoder Portable | 185.0 MB Links: Shutter Encoder Home Page | FAQ / Tips | macOS | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
  • Recent Achievements

    • Reacting Well
      NovaEdgeX earned a badge
      Reacting Well
    • Week One Done
      NovaEdgeX earned a badge
      Week One Done
    • One Year In
      BA the Curmudgeon earned a badge
      One Year In
    • Conversation Starter
      rosiecharles earned a badge
      Conversation Starter
    • First Post
      KMilenkoski1202 earned a badge
      First Post
  • Popular Contributors

    1. 1
      +primortal
      534
    2. 2
      +Edouard
      265
    3. 3
      PsYcHoKiLLa
      152
    4. 4
      Steven P.
      99
    5. 5
      macoman
      66
  • Tell a friend

    Love Neowin? Tell a friend!