Recommended Posts

I have a friend who has been using SSDs for YEARS. He works for a retailer and therefore gets to play about with them all the time (also to note is he has 8x SSDs on his personal machine). After all of these years he's had ONE SSD fail him. Now try and compare that to the amount of HDD fails he's had and you suddenly realize SSDs are less likely to fail.

Exactly. I've upgraded my PCs through tons of SSDs, starting with the OCZ Vertex 1. Not a single one of them have failed. I've also built numerous PC's for a company I do consulting work for, and again not a single one has failed so far. 95% of those are OCZ Vertex SSDs, which a lot of people claim have a high failure rate, so I'd say it's pretty impressive. I've had quite a few HDDs die over the years, so in my personal experience, SSDs are a huge step forward in reliability.

In the end, there's simply no sense in thinking a HDD is more reliable than a SSD. HDDs bow to the physics gods, and there's nothing humanly possible to fight that. SSDs have no mechanics and only die due to controller or firmware defects. Both of which are getting exponentially better year over year.

It's also worth noting that in theory he's correct, since each block of the memory can only be written/erased a certain number of times. The controllers manage that though and therefore heavily prolong the life of them.

Saying you're not going to buy an SSD because you're worried about data loss is silly imo. You're missing out on a SIGNIFICANT performance increase and for what? Potential data loss? Lets say 4 years down the line it dies quite frankly if you don't have a backup of that drive, you've failed at computing 101.

There's no need to worry about read/write cycles. SSDs have more than enough cycles to last much much longer than anybody sane would use it for.

http://www.tomshardware.com/reviews/ssd-reliability-failure-rate,2923.html

There's no need to worry about read/write cycles. SSDs have more than enough cycles to last much much longer than anybody sane would use it for.

http://www.tomshardw...-rate,2923.html

That's why I noted that the controller would prolong, just in case there was any doubt. :p When I was learning about the theory behind NAND memory at university I did a lot of research into it, which is why I'm confused that there's a misconception that they have a high rate of failing. Without any controllers (and other bits keeping it going) I can see why people might think that would be the case but the reality is they're reliable thanks to those things.

"When a SSD fails, the failure is likely to be catastrophic, with total data loss. HDDs can fail in this way too, but often give warning that they are failing, allowing much or all of their data to be recovered". Also: wear leveling, bugged controllers with subsequent loss of data and some other issues I don't have time to research right now.

https://secure.wikim...ard_disk_drives

For me, right now SSDs are a no-go. Miniaturization will bring this very limited and controller-dependent storage technology to an halt. NAND Flash isn't for storing data, not for me.

The only way an SSD is going to fail catastrophically is when a physical NAND chip gives way (similar to if a platter in a HDD gave way).

SSDs use striping, ECC and (depending on the controller) a couple of other methods to maintain the data on them, in all cases they can recover from a dead cell (like a bad sector on a HDD) unless there is a physical chip failure.

The S.M.A.R.T. readings on a SSD are far more indicative of drive health in SSDs as the death of a drive is gradual due to degrading memory, thus you can see when a drive begins to die, where as most failures in HDDs are due to physical malfunctions such as dying rotors/heads or disk crashes.

I am bemused at your reference to wear leveling above, as that makes no change (negatively) to the lifetime of a drive, and dramatically improves the drives life by writing pages into areas of the NAND that have been erased the least. Bugged controllers can lead to lost data, however I am yet to become aware of a bugger controller that wasn't related to a specific firmware release, and am yet to see a loss of data from these bugs. This is in direct contrast to Seagates head parking firmware woes recently.

Add to this technologies such as write amplification management and disk based compression, and the drives are highly fault tolerant and capable of dealing with more erases than would be readily apparent.

If I may be so bold as to suggest, that making assertions as to complex technologies, and then stating "wear leveling, bugged controllers with subsequent loss of data and some other issues I don't have time to research right now." (which is nonsensical btw) would suggest that perhaps you ought not be commenting authoritatively on the subject?

The one thing you did get right however, is that miniaturisation (the shrinking of the die size on a chip) will indeed kill off SSDs in the long run. As the process for creating the cell shrinks, the sells become less capable of holding a charge with each erase. This situation is dramatically magnified by the MLC (multi level cells) which hold 2 bits of data by storing a different voltage inhibition (this is wrong, but without getting into the nitty gritty of it) in the cell. The erases make cells less capable of dealing with differing voltages on read, and thus are likely to fail more readily than simple on off assemblies like SLC (single level cells).

Bleh.

I thought an SSD burns out relatively quickly ... or is that wrong ?

Relative to HDDs, you are entirely right. The thing is that you will (generally) be upgrading your computer a LONG time before the disk dies. The average disk life is projected at longer than 10 years. Mine is currently projected to live for another 9 years. and I've had my Vertex 3 for a couple of years and abuse the little ****** like crazy.

tl;dr - Yes, but it won't worry you unless you deliberately try to burn out the disk.

Edited by articuno1au

"When a SSD fails, the failure is likely to be catastrophic, with total data loss. HDDs can fail in this way too, but often give warning that they are failing, allowing much or all of their data to be recovered". Also: wear leveling, bugged controllers with subsequent loss of data and some other issues I don't have time to research right now.

https://secure.wikim...ard_disk_drives

For me, right now SSDs are a no-go. Miniaturization will bring this very limited and controller-dependent storage technology to an halt. NAND Flash isn't for storing data, not for me.

I don?t know who wrote that, but I take issue with it.

HDD are one of the few mechanical pieces of a modern computer. This opens the door to mechanical failures, especially as they operate at such high speeds.

Of course SSDs do experience electronic failures, but this would likely be due to a manufacturing defect or electrical damage. And the same is true of HDDs as well.

Generally, when an SSD, it is a planned failure due to wear. When a HDD fails it is a catastrophic, unplanned mechanical failure.

As for buying advice, you're in luck as SSD prices have begun to drop. Right now there's an amazing deal on the Crucial 256GB m4 for just $170! Ends today, I think, so I'd hurry.

That's why I noted that the controller would prolong, just in case there was any doubt. :p When I was learning about the theory behind NAND memory at university I did a lot of research into it, which is why I'm confused that there's a misconception that they have a high rate of failing. Without any controllers (and other bits keeping it going) I can see why people might think that would be the case but the reality is they're reliable thanks to those things.

I think some people take Newegg reviews too much at heart. haha :p

I don?t know who wrote that, but I take issue with it.

HDD are one of the few mechanical pieces of a modern computer. This opens the door to mechanical failures, especially as they operate at such high speeds.

Of course SSDs do experience electronic failures, but this would likely be due to a manufacturing defect or electrical damage. And the same is true of HDDs as well.

Generally, when an SSD, it is a planned failure due to wear. When a HDD fails it is a catastrophic, unplanned mechanical failure.

As for buying advice, your in luck as SSD prices have begun to drop. Right now there's an amazing deal on the Crucial 256GB m4 for just $170! End today, I think, so I'd hurry.

Personally I'd recommend him to wait a few days as Corsair are rumoured to be launching their new Neutron series soon.

http://www.corsair.com/neutron/

I think some people take Newegg reviews too much at heart. haha :p

Well the OCZ Vertex 1's didn't really help the reliability case eh? :p

Well the OCZ Vertex 1's didn't really help the reliability case eh? :p

Those Sandforce controllers did seem to be a problem for some people. My Vertex 1 has been running strong for the past 6 years or so, and probably has a million read/writes on it. I should do a life scan on that thing and see how much longer it thinks it will survive. :)

Those Sandforce controllers did seem to be a problem for some people. My Vertex 1 has been running strong for the past 6 years or so, and probably has a million read/writes on it. I should do a life scan on that thing and see how much longer it thinks it will survive. :)

Yeah, thank god for Marvel. <_< I'm going to do the same out of curiosity.

edit: 8 years, ntb.

Image%202012-07-23%20at%209.10.52%20PM.png

Mine is both bigger, and more used!

My penis SSD is way better than yours :p

(I'm just kidding. I'm sure you won't be offended, but thought I had better say so >.<)

LOLLLLLLL........

It's not how big it is, it's how you use it.. :shifty:

I find it curious you've powered it on 60x but it's been online for 5000+ hours. :o You really don't like turning it off eh?

  • Like 2

From your question above, I highly recommend you get SSD and Windows installed by a professional. Windows 7 takes about 20GB when installed.

Windows 8, surprisingly, takes up about the same amount of space. The real space eaters with Windows (XP and later) aren't the OS or even applications and games, but data files the applications and games access - precisely the features that should NOT be parked on an SSD.

The reason SSDs are such major performance boosters is the same reason thumb-drives eat optical drives for lunch when doing installation - utterly-ridiculous read performance.

I proved this to myself rather easily (and despite not having this in mind) - I bought two 8GB USB 2.0 thumb drives (one specifically for OS install testing).

That target system is, in fact my test-bench system, with the following setup -

CPU - Intel Q6600

RAM - 4GB DDR2-800 (2GB x2)

HDD - WD AC1000 (1TB ex-MyBook converted to desktop use) SATA-3.0g HDD

ODD - Samsung SH-223B SATA optical drive (comparison)

KB - Microsoft Wireless Desktop 6000 V.3 (USB)

Mouse - Logitech V220 Cordless (USB)

OS - Windows 8 Release Preview x64

MB - ASUS P5G41T-M LX2/GB

The thumbdrive itself is a MicroCenter 8GB USB thumbdrive (the same ones that they have been selling for $5.99 in their stores). Thumbdrives, like SSDs, are based on flash memory - in fact, one could say that an SSD is a thumbdrive writ large. However. thumbdrives, unlike SSDs, are designed around the USB externally-hot-pluggable specification (SSDs are designed generally for SATA or the mSATA spec for desktops or portable uses). I configured the test thumbdrive using the freely-available USB/DVD image configuration tool from the Microsoft Online Store, and using the downloadable ISO image of the Release Preview.

Okay. We have our contenders - optical drive vs. thumbdrive. SATA-150 vs. USB 2.0. Internal vs. external.

Winner - USB, and it wasn't close. The thumbdrive took less than half the install time compared to the optical drive.

The why of it - While USB thumbdrives (in fact, flash memory in general) has somewhat of a write lag (exacerbated in the case of thumbdrives by the lower-quality flash compared to SSDs) compared to magnetic media (such as hard drives) when a flash drive is the source, it utterly lacks a *read lag* compared to an optical drive - thus a flash-based source has the best transfer rates to any target (non-RAID sources, that is).

Internally, an SSD is structured similarly to a RAID array of thumbdrives; just as a RAID array of hard drives has better throughput than a single drive in the array, the same is true of an SSD compared to a thumbdrive. (Scaling upward, the same is, naturally, true of SSD-based RAID arrays compared to single SSDs.)

Remember, I used older hardware in the *seat of the pants* test - not modern hardware. Optical-drive performance has, in fact, gotten NO faster since; the same can't be said of even thumb drives, let alone SSDs. That means that optical drives are even further in the performance doghouse.

He's right, except the read lag he is referring to is latency, and the latency is the big difference as opposed to the increase in read speed (throughput).

For ****s and giggles. USB -> SSD WIndows installs are BLAZINGLY fast :p

USB3 -> SSD installs will make you cream your pants :p

LOLLLLLLL........

It's not how big it is, it's how you use it.. :shifty:

I find it curious you've powered it on 60x but it's been online for 5000+ hours. :o You really don't like turning it off eh?

That, and certain firmware updates reset certain smart values (specifically powered on times. It's the only one I have ever noticed).

I work and play off of this machine, It doesn't get turned off much :p

SSD = HUGE performance gain, IF your existing HDD is not performing as well as you'd expect. My Vertex+ Sata II drive replaced my WD 420gb as a boot disk, and I notice a huge difference. If you go Sata III with a new generation chipset the performance gains are exceptional. And as for stability and crash-proof; just maintain a backup. Same rule applies with ANY drive future, past or present that you want to preserve the data of.

Those Sandforce controllers did seem to be a problem for some people. My Vertex 1 has been running strong for the past 6 years or so, and probably has a million read/writes on it. I should do a life scan on that thing and see how much longer it thinks it will survive. :)

OCZ vertex has been out for 3 years. My first SSD was an OCZ Vertex 60GB. I got it because it was cheap, and it failed within 4 months. I've seen a few articles on the internet stating OCZ is the worst in terms of SSD reliability. I believe it, my friend's OCZ also died. I've been rocking Intel since late 2009, and still going strong.

I have two SSD's in Raid0 in my (otherwise not so extremely well-spec'd) laptop and all I can say is that it is absolutely amazing. Windows boots in around 15 seconds and everything launches completely instantly. Getting an SSD is the single best upgrade you can do for pretty much any PC nowadays. Go for it!

Yeah, you're wrong. I'm particularly amused that no-one picked up on "faster on newer hardware" as that's just complete tosh.

Nand doesn't degrade when not in use where as magnetic mediums do; So for pure storage (i.e. plug in, copy, unplug), the only downside of SSDs is cost. Even on scratch disks the drives survive for longer than the lifetime of the computer and S.M.A.R.T. is more accurate in predicting its impending death.

For those of us that are interested in performance the SSDs are immeasurably better due to their extremely low latency. Whilst I agree that performance isn't everything, this is a worthwhile performance boost.

Technically untrue. As the SSDs shrink in die size, the NAND memory becomes less durable and slower.

I would however agree that the firmware is a million times better now than it was then.

Not once did I say that NAND wouldn't die. :p Firmware improves NAND writes by making sure all the cells are written to equally, this is why previous firmwares failed to fix since you would go through NAND writes pretty fast. Also, I did state that in my opinion, a SSD is likely to fail as a HDD so the whole argument which is more reliable is very mute as they both have issues of their own. A SSD or HDD will never be 100% reliable.

Sorry but the one who knows very little about NAND flash it's you: memory cells are a long-term nightmare for anyone caring for his or her data.

Anyone caring for his/her data does not keep it in one place. You BACKUP and then BACKUP THE BACKUP (and once again if you are paranoid).

He's right, except the read lag he is referring to is latency, and the latency is the big difference as opposed to the increase in read speed (throughput).

For ****s and giggles. USB -> SSD WIndows installs are BLAZINGLY fast :p

USB3 -> SSD installs will make you cream your pants :p

That, and certain firmware updates reset certain smart values (specifically powered on times. It's the only one I have ever noticed).

I work and play off of this machine, It doesn't get turned off much :p

Agreed - which is, in fact, the other half of the argument.

The motherboard used for my *seat-of-the-pants* test is based on the consumer-stable/corporate-stable Intel G41 chipset with the ICH7 southbridge.

No AHCI support. No RAID. SATA support tops out at SATA-3.0g. USB support is only 2.0.

For that reason, I configured my *second* 8GB thumbdrive as install media (Windows 7) - even USB 2.0 speeds kick the crap out of optical-drive speeds for installation - and that's just to hard drives.

Installing to SSD (even from the same speed USB 2.0 thumbdrives) will naturally be faster, with USB 3.0-based thumbdrives faster still.

Even more telling, 8GB drives are far from expensive - MicroCenter is still selling the same thumbdrives I bought two weeks ago (Fairfax, VA) for all of $5.99 each - USB 3.0-rated drives (same size) are $3 more each.

Buy *at least one* when you buy the motherboard for your build; if you're still trying to decide between Windows 8 and Windows 7, buy two - one for each. Build PCs for others? Include a system-restore thumbdrive.

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • How to Do More with Less: Future-Proofing Yourself in an AI-driven Economy —was $28 now FREE by Steven Parker Claim your complimentary copy (worth $28) of "How to Do More with Less: Future-Proofing Yourself in an AI-driven Economy" for free, before the offer ends on June 30. Description In today’s workplace, headlines about artificial intelligence can feel overwhelming. With headlines swinging between promises of utopia and warnings of mass unemployment, for most knowledge workers, the truth feels unclear. In this book, Sharon Gai cuts through the noise. Drawing from real-world examples and global insights, she explains how AI is reshaping the way we work—without hype or fearmongering. Instead of choosing between blind optimism or outright pessimism, she offers a practical, balanced perspective that helps readers make sense of the rapidly evolving AI landscape. You’ll learn how to: Reskill and future-proof your career in the face of AI disruption Identify which parts of your role can be automated, and which require human creativity and judgment Use proven frameworks to evaluate AI’s impact on your work and your organization Apply actionable tips and tools to boost productivity, make smarter decisions, and do more with less Gain clarity as a parent, leader, or professional navigating what this means for the next generation Whether you’re an employee anxious about your future, a parent concerned about your children’s opportunities, or a leader managing a lean team with tight budgets, this book provides the strategies and mindset you need to adapt so you can stop worrying and start preparing. How to download for free Please ensure you read the terms and conditions to claim this offer. Complete and verifiable information is required in order to receive this free offer. If you have previously made use of these offers, you will not need to re-register. Was $28, but is now FREE | Below free offer link expires on June 30. How to Do More with Less: Future-Proofing Yourself in an AI-driven Economy The below offers are also available for free in exchange for your (work) email: The Vibe Coding Playbook: Building Your Tech Business with AI ($35 Value) FREE - Expires 6/23 The Persuasion Engine: How Any Business Can Use AI-Powered Neuromarketing to Understand and Win Customers ($28 Value) FREE - Expires 6/24 How to Do More with Less: Future-Proofing Yourself in an AI-driven Economy ($28 Value) FREE - Expires 6/30 Cloud Security Fundamentals: Building the Foundations for Secure Cloud Platforms ($131.95 Value) FREE - Expires 7/1 The Complete Free AI Learning: Master ChatGPT, Claude, Gemini & More ($21 Value) FREE How to Build an AI Design Workflow with Gamma ($21 Value) FREE The Ultimate Linux Newbie Guide – Featured Free content Python Notes for Professionals – Featured Free content Learn Linux in 5 Days – Featured Free content Quick Reference Guide for Cybersecurity – Featured Free content We post these because we earn commission on each lead so as not to rely solely on advertising, which many of our readers block. It all helps toward paying staff reporters, servers and hosting costs. Other ways to support Neowin The above deal not doing it for you, but still want to help? Check out the links below. Check out our partner software in the Neowin Store Buy a T-shirt at Neowin's Threadsquad Subscribe to Neowin - for $14 a year, or $28 a year for an ad-free experience Disclosure: An account at Neowin Deals is required to participate in any deals powered by our affiliate, StackCommerce. For a full description of StackCommerce's privacy guidelines, go here. Neowin benefits from shared revenue of each sale made through the branded deals site.
    • Microsoft admits one of the most crucial Outlook features is currently broken by Sayan Sen Microsoft is making some decent progress when it comes to Windows 11. Recently we have confirmed reports of some rather useful improvements landing in the next version of the OS, 26H2, wherein GPU driver TDR crashes may finally be fixed, plus the company is also allowing users to disable web content on the Search. On the Outlook front though things have not been so rosy. Last month in May we reported several problems affecting basic functionalities on the app. These included a problem where documents would open blank or corrupt themselves. Following that, Quick Steps, a very useful feature, would no longer work correctly, and finally, Microsoft acknowledged a problem wherein images would fail to load up properly inside the email. Microsoft had resolved those bugs later and almost exactly a month after we reported on them, the company has now admitted a new similarly basic issue, this time on Macs. Users recently started noticing that Outlook would no longer display email threads properly as the original message itself was not displayed. An affected user Tsoumpas, C (ngmb) nicely described the problem in a forum post they made on Microsoft's site. They wrote: "Description of the issue: After updating Outlook for Mac [Version 16.110 (26061317)] on 18/6/2026, replying to any email no longer includes the original message in the reply window. Prior to the update, replies correctly contained the original email text below my response. Expected behavior: The original message should be included in the reply, as in previous Outlook versions and according to the configured reply settings. Actual behavior: The reply window contains only a blank composition area (or only my response), with none of the original email text included." Obviously this must be a highly frustrating for users as noted by several in that thread. The post, at the time of writing, has also been upvoted by more than 40 users indicating that is a fairly widespread bug. Thankfully Microsoft seems to have acknowledged the problem right around that time as it opened a new issue on its official website. In the support article, the company recommends switching to Outlook for Mac from the legacy app, where the problem appears to be happening.
    • PotPlayer 260622 by Razvan Serea PotPlayer is an extremely light-weight multimedia player for Windows. It feels like the KMPlayer, but is in active development. Supports almost every available video formats out there. PotPlayer contains internal codecs and there is no need to install codecs manually. Other key features include WebCam/Analog/Digital TV devices support, gapless video playback, DXVA, live broadcasting. Distinctive features of the player is a high quality playback, support for all modern video and audio formats and a built DXVA video codecs. A wide range of subtitles are supported and you are also able to capture audio, video, and screenshots. A comprehensive video and audio player, that also supports TV channels, subtitles and skins. Its been described on the Internet as The KMPlayer redux, and it pretty much is. Daum PotPlayer 260622 (1.7.22963) changelog: Removed Kakao TV Added pause function when navigating via the navigation bar Significantly improved internal stability Fixed an issue where colors appeared strange during RGB24 processing Improved playback for some HTTP streams Improved sync processing for the built-in audio renderer Fixed an issue where certain MP4 files behaved abnormally during playback Download: Daum PotPlayer (64-bit) | 54.7 MB (Freeware) Download: Daum PotPlayer (32-bit) | 61.1 MB View: Daum PotPlayer Home Page | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • Tixati 3.44 is out.
  • Recent Achievements

    • Dedicated
      tuben earned a badge
      Dedicated
    • Week One Done
      mnsgroup earned a badge
      Week One Done
    • Conversation Starter
      sumytbe earned a badge
      Conversation Starter
    • One Year In
      B4dM1k3 earned a badge
      One Year In
    • One Year In
      DarkWun earned a badge
      One Year In
  • Popular Contributors

    1. 1
      +primortal
      522
    2. 2
      +Edouard
      199
    3. 3
      PsYcHoKiLLa
      94
    4. 4
      Michael Scrip
      82
    5. 5
      neufuse
      69
  • Tell a friend

    Love Neowin? Tell a friend!