Recommended Posts

usually when upgrading from the same releases, DD-WRT->DD-WRT, Tomato->Tomato(here you might need to differentiate between builds) you generally don't need to wipe.

I used to do that and choose not to wipe but after a few builds I was getting major crashes so wiped and flashed that build again and everything was fine

So from then on I just backup > flash&wipe > restore

It only takes a few seconds extra and easier to troubleshoot knowing its a clean flash

Link to comment
https://www.neowin.net/forum/topic/1094439-dd-wrt/page/4/#findComment-595428276
Share on other sites

Just goto administration > backup and save the settings to a file, thats how I upgrade > wipe > restore and all my settings are exactly the same as they were before I wiped

Thanks for the tip. Still, unless I'm experiencing problems with a particular bug or need one of the new features I'm incline to just stick with my current setup which seems more-or-less rock solid to me.

Link to comment
https://www.neowin.net/forum/topic/1094439-dd-wrt/page/4/#findComment-595428364
Share on other sites

"Why would I swap them? Why would I run the gateway/router stairs when the mode is downstairs and more central in the hous"

You can not be that dense?? Really?? :blink:

Move the BOX that is v2 that can run your tomato firmware you so happy with to you NOC (kitchen).. And place the V1 that runs the dd-wrt that you despise :rolleyes: (but use anyway) where you currently have the AP.

But as I said in my other reply, my v2 with tomato, is my main router,in the Kitchen, the V1 with DD-WRT. acts as a upstairs network switch and AP. As for using DD-WRT despite despising is, as I said before, I had to before when I had to bridge the upstairs computer room with the downstairs network wirelessly., before I laid the cable, which I need to redo anyway since it's an old cable that's in worse shape than I thought and only does 100MBit, though I don't really need more, but it's effectively the backbone so...

Link to comment
https://www.neowin.net/forum/topic/1094439-dd-wrt/page/4/#findComment-595428678
Share on other sites

Signs you know your router is too old - no more new firmware for it. :) Just looked at the new DD-WRT FTP link you supplied, my model isn't listed (WRT54GL), so will stick with what I have now:

DD-WRT v24-sp2 (08/07/10) std

(SVN revision 14896)

It works fine for me and has no crashes or lockups which is what I am after. But I am a sucker for new goodies in firmware. (Just thought i'd peruse it to see what was new in there).

Link to comment
https://www.neowin.net/forum/topic/1094439-dd-wrt/page/4/#findComment-595428706
Share on other sites

Signs you know your router is too old - no more new firmware for it. :) Just looked at the new DD-WRT FTP link you supplied, my model isn't listed (WRT54GL), so will stick with what I have now:

DD-WRT v24-sp2 (08/07/10) std

(SVN revision 14896)

It works fine for me and has no crashes or lockups which is what I am after. But I am a sucker for new goodies in firmware. (Just thought i'd peruse it to see what was new in there).

Dude, a WRT-54G? Time for a new router.

Link to comment
https://www.neowin.net/forum/topic/1094439-dd-wrt/page/4/#findComment-595428716
Share on other sites

Signs you know your router is too old - no more new firmware for it. :) Just looked at the new DD-WRT FTP link you supplied, my model isn't listed (WRT54GL), so will stick with what I have now:

DD-WRT v24-sp2 (08/07/10) std

(SVN revision 14896)

It works fine for me and has no crashes or lockups which is what I am after. But I am a sucker for new goodies in firmware. (Just thought i'd peruse it to see what was new in there).

Following the recommended firmware links on this page, it looks like there is a newer build for your router

http://www.dd-wrt.com/wiki/index.php/Linksys_WRT54GL#Firmware

http://www.dd-wrt.com/phpBB2/viewtopic.php?t=52043

Link to comment
https://www.neowin.net/forum/topic/1094439-dd-wrt/page/4/#findComment-595428736
Share on other sites

WRT54's are rock solid though, and if you don't need more than G speeds they are some of the most optimized routers on tomato there is outperforming many of the newer "faster" routers for a lot of things.

but yeah, it's old and "slow" for network speeds. but on the other hand, they're rock solid and basically the foundation of custom firmware.

Link to comment
https://www.neowin.net/forum/topic/1094439-dd-wrt/page/4/#findComment-595428770
Share on other sites

did we have to break the topic into 3 parts? "dd-wrt" part one, "is the project dead?" as a tag part 2, and finally "it hasn't been updated in a couple years." as the contents (part 3)?

couldn't you of just said dd-wrt is this project dead? it hasn't been updated in a couple years"......

but no it's not dead, look at the nightly change logs..

Link to comment
https://www.neowin.net/forum/topic/1094439-dd-wrt/page/4/#findComment-595428776
Share on other sites

WRT54's are rock solid though, and if you don't need more than G speeds they are some of the most optimized routers on tomato there is outperforming many of the newer "faster" routers for a lot of things.

but yeah, it's old and "slow" for network speeds. but on the other hand, they're rock solid and basically the foundation of custom firmware.

I'm not sure if you're a Cisco / Linksys fan boy, but you're starting to become annoying with your BS.

Please show me where / how the older WRT54 models out perform newer routers? No gigabit ports, slower Wi-Fi speeds and a much slower / older processing chip and less memory. Not to mention some of the v1 - v2 models use to overheat.

You acknowledge "it's old and slow" but what other ways can you show me how they "outperform" newer routers. - Please teach me.

The only bonus from these routers were the custom firmwares running from Linux. These routers are way past their time.

The design and colours were great, back then, but even that was flawed with their crappy stacking and overheating ability.

Link to comment
https://www.neowin.net/forum/topic/1094439-dd-wrt/page/4/#findComment-595428786
Share on other sites

Did I mention anything about network speed or anything.

I have however used both WRT54's and other devices, and a WRT54 with tomato is extremely efficient at handling QoS traffic management, remember not EVERYTHING is about cpu speeds, and as I Said, these custom firmwares pretty much started with the WRT54, and they have been optimized a lot.

personally I wouldn't use a WRT54 today, as they don't offer the speeds I need, but as I specifically mentioned in my post, if you don't need anything faster it's a rock solid device with an extremely efficient firmware that's tried and tested more than any other.

speaking of people getting annoying, your inability to read posts and picking fights and trolling is really annoying. Now what are you even doing in a DD-WRT thread since you don't even use DD-WRT or devices that can run it.

Link to comment
https://www.neowin.net/forum/topic/1094439-dd-wrt/page/4/#findComment-595428802
Share on other sites

speaking of people getting annoying, your inability to read posts and picking fights and trolling is really annoying. Now what are you even doing in a DD-WRT thread since you don't even use DD-WRT or devices that can run it.

We finally got there. First it was grammar, now it's the troll. Congrats - as mentioned previously.

I came in this thread to express my opinion, that's what Internet forums are for. To which you replied with a false statement and I corrected you to which you oblivious couldn't take, being proved wrong.

"WRT54 with tomato is extremely efficient at handling QoS traffic management"

Again, please show me an example of how the QoS is more "extremely efficient" than a newer router running DD-WRT.

After all, you said it "outperforms newer routers".

Link to comment
https://www.neowin.net/forum/topic/1094439-dd-wrt/page/4/#findComment-595428812
Share on other sites

I have however used both WRT54's and other devices, and a WRT54 with tomato is extremely efficient at handling QoS traffic management, remember not EVERYTHING is about cpu speeds, and as I Said, these custom firmwares pretty much started with the WRT54, and they have been optimized a lot.

personally I wouldn't use a WRT54 today, as they don't offer the speeds I need, but as I specifically mentioned in my post, if you don't need anything faster it's a rock solid device with an extremely efficient firmware that's tried and tested more than any other.

If you had all that and 2 nickels, you'd have 10 cents.

Do 54Gs die? No, not really. But I see tons of them with little weird problems (such as one that would not display the totality of a website we were creating for a client) that are remedied as soon as its replaced. They are pushing 10 years old. Routers are cheap. No reason to hold onto legacy hardware because 'it started with them!'. Else I'd be sitting with a pile of punchcards next to me.

Link to comment
https://www.neowin.net/forum/topic/1094439-dd-wrt/page/4/#findComment-595428862
Share on other sites

If you had all that and 2 nickels, you'd have 10 cents.

Do 54Gs die? No, not really. But I see tons of them with little weird problems (such as one that would not display the totality of a website we were creating for a client) that are remedied as soon as its replaced. They are pushing 10 years old. Routers are cheap. No reason to hold onto legacy hardware because 'it started with them!'. Else I'd be sitting with a pile of punchcards next to me.

my only concern is IPV6 at the moment when my ISP plans to turn it on sometime this year. I support my whole extended family which is about 2 dozen different homes at least.

Link to comment
https://www.neowin.net/forum/topic/1094439-dd-wrt/page/4/#findComment-595428884
Share on other sites

Dude, a WRT-54G? Time for a new router.

Yeah - I KNOW! :) Gotta wait a bit before I go sink more $$$ in my PC budget. (for goodies like these). As soon as I can get on a newer router I surely will.

The router - I agree is old and rock solid at the same time too. For most applications, it works fine so hard to justify replacing sometimes. But, on the occasion, I do get the bug to want to upgrade the thing with more RAM so I can play a bit more with it. I tried the SD card mod but failed on that one after burning out a microsd with my amateur soldering skills. A skilled solder jockey would do it easily, but not me.

Link to comment
https://www.neowin.net/forum/topic/1094439-dd-wrt/page/4/#findComment-595429314
Share on other sites

I'm stil using a wrt54gs v1.1. It's been used since I got it in 2003-ish. It's been running stock Tomato 1.28 since the last release until I discovered the Tomato USB branch not too long ago.

There may not be a reason to stick with old hardware but there hasn't been a reason for me to need to get a new one either.

Link to comment
https://www.neowin.net/forum/topic/1094439-dd-wrt/page/4/#findComment-595429320
Share on other sites

my only concern is IPV6 at the moment when my ISP plans to turn it on sometime this year. I support my whole extended family which is about 2 dozen different homes at least.

Unless they also plan to kill ipv4 support at the same time, don't think your extended family will care or notice

Link to comment
https://www.neowin.net/forum/topic/1094439-dd-wrt/page/4/#findComment-595429668
Share on other sites

^ very true -- your everyday user has little use or care for ipv6. So what if their isp turns it on? Doesn't mean they have to use it.

Until such time that there are websites/services that they need to access that are ONLY available via ipv6, its not of any use to normal users. If I had to guess I would say you got a good 20 years before you have to worry about it for the every day user ;)

Now on the other hand, part of the reason I run a full blown distro for my router, is pfsense has great IPv6 support. I was running a tunnel from HE for quite some time without any issues at all. And now that my isp has finally turned on native support I have switched to that.

To be honest the tunnel was a bit easier to manage. But again for your every day user, it makes no difference if their isp turns on ipv6 or not. Most of them don't even know what an IP address is in the first place be it v4 or v6 ;)

Link to comment
https://www.neowin.net/forum/topic/1094439-dd-wrt/page/4/#findComment-595430056
Share on other sites

  • 2 weeks later...

my only concern is IPV6 at the moment when my ISP plans to turn it on sometime this year. I support my whole extended family which is about 2 dozen different homes at least.

Here's a surprise - I'd recommend Netgear's WNDR3700 (v2 and newer), including, if not especially, the newest (v4) despite the lack of non-factory firmware support.

First off, it actually supports IPv6 (though it is disabled by default) - if your ISP (via customer-premises equipment - supplied by them OR you) supports IPv6 (or you have a tunnel), this router can use it. Comcast supports IPv6 via 6to4 tunnel where 6RD is not present (this router's factory firmware doesn't support 6RD).

It supports mixed networks as well (my home LAN has two wired and two wireless PCs/devices, with one PC having two wired [one 100 mbps and one gigabit] and a wireless[wireless-G] connection, one PC a 100 mbps wired connection, a legacy laptop with wireless-G, and a smart TV/device with wireless-N - all except the TV are known to support IPv6; the TV DOES support 5 GHz N, which it occupies all by its lonesome).

However, if you feel better with third-party support, the v4 may well be too NEW for you.

Link to comment
https://www.neowin.net/forum/topic/1094439-dd-wrt/page/4/#findComment-595450226
Share on other sites

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Micron reveals AI companies are spending billions to lock up its memory years in advance by Karthik Mudaliar The demand for more memory is far from over, and Micron is turning the AI-driven memory shortage into a much more predictable business. The company has revealed that it has signed 16 strategic supply agreements backed by roughly $22 billion in customer deposits and other financial commitments. The contracts cover DRAM and NAND deliveries over several years, with some running through 2030. With the AI boom, demand for high-bandwidth memory (HBM) has grown so quickly that large customers are now prepared to help finance future production in exchange for a guaranteed supply. According to Micron’s latest financial results, the company received commitments worth about $22 billion across its new agreements. Around $18 billion is expected to arrive as cash deposits, while the rest will come through other financial arrangements. Micron says the agreements could generate approximately $100 billion in future contracted obligations. They cover around 20% of its expected DRAM shipments and one-third of its NAND shipments during their respective terms. It should be noted that although AI infrastructure is the main force behind the current shortage, not all 16 agreements with Micron involve AI companies. Micron said the customers also include consumer electronics and automotive businesses, two sectors that increasingly compete with data centers for the same manufacturing capacity. HBM is consuming an increasing share of that supply. Unlike conventional desktop or server RAM, HBM stacks multiple memory dies vertically and places them close to an AI accelerator. This gives GPUs and other AI chips access to data at much higher speeds, but it also requires more complicated manufacturing and packaging. Micron says its 12-layer HBM4 memory is now shipping in high volume for a lead customer, with samples also supplied to other companies. The chipmaker has already generated more than $1 billion in HBM4 revenue and says the product is ramping twice as quickly as its earlier HBM3E generation. Samsung has similarly warned that the memory shortage could continue into 2027 and beyond. Consumer memory companies have also had to address sharp increases in DDR5 pricing, suggesting the effects are already reaching beyond the data center. For consumers, that could mean the AI memory crunch lasts longer than expected, even as manufacturers invest heavily in new production.
    • XnConvert 1.112 by Razvan Serea  XnConvert is a cross-platform batch image-converter and resizer with a powerful and ease of use experience. All common picture and graphics formats are supported (i.e. JPG, PNG, TIFF, GIF, Camera RAW, JPEG2000, WebP, OpenEXR) as well as supporting over 500 other image formats. Also available within the batch operations include rotating, adding of watermarks, adding of text along with many image-adjustment features such as brightness, shadows and more. Among the features included are: Batch adding of files and folders Support for drag and drop of files Batch rotating, cropping, resizing and more Adding of photo masks Preserving or removing image metadata in conversions Multipage image file support (i.e animated GIF, APNG, TIFF) Command line integration via NConvert Filters - such as 'Blur', 'Gaussian Blur', 'Emboss', "Sharpen' and much more Effects - such as 'Old camera' and much more Download: XnConvert 64-bit | Standalone | ~30.0 MB (Freeware) Download: XnConvert 32-bit | Standalone Links: XnConvert Website | Screenshot | Release Announcement Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • Microsoft updates Visual Studio Code with chat cost tracking and multi-agent chats by Paul Hill Microsoft has just launched Visual Studio Code 1.126, its latest weekly release. This time, the company has focused on letting you see the total cost of chat sessions to spot expensive conversations; enabling multiple chats per session that run side-by-side in one agent host Copilot session; and letting you browse new folders safely in restricted mode. We have now reached the stage where free AI in IDEs is coming to an end. To help you keep track of your costs, VS Code now lets you see the entire cost of a chat session, rather than just individual turns. This should give you more transparency about which sessions consume the most credits, so you can better manage your usage over time and spend less. For those of you using the Agents window, you know it is possible to run and manage multiple agent sessions at once. In this update, a Copilot session started from an agent host can hold several chats at once. Explaining how this feature works, Microsoft writes: Finally, from this update forward, Microsoft will remove the pop-up when opening an untrusted folder. When you open a new folder now, it will automatically open in Restricted Mode. You will see a banner that lets you manage the trust level of the folder. Microsoft has made this change so that it’s easier to start inspecting code without giving it trust right away. If you have VS Code, you can check for updates within the app now to get this new version. Otherwise, you can download it from the Visual Studio Code website.
    • Anthropic accuses Alibaba of using 25,000 fake accounts to copy Claude's capabilities by Karthik Mudaliar Anthropic has accused Alibaba of using nearly 25,000 fraudulent accounts to extract capabilities from Claude on a huge scale. According to a report from Reuters, Anthropic told US lawmakers that operators linked to Alibaba and the company’s Qwen AI team generated 28.8 million exchanges with Claude between April 22 and June 5, 2026. That is a lot of Claude conversations, but Anthropic says this was not ordinary chatbot use. The company believes the accounts were part of a coordinated effort to collect answers that could help train or improve rival AI systems. The alleged campaign reportedly focused on some of Claude’s most valuable skills, including software development, multi-step reasoning, and agentic tasks. In practical terms, that means getting an AI model to plan and complete work across several stages rather than simply answering a single question. This is called 'distillation,' where AI companies use outputs from a larger model to train a smaller and cheaper one. The smaller model learns to imitate useful parts of the more capable system without needing the same amount of computing power. The distillation process isn't automatically suspicious, but the problem comes when one company gathers another provider's outputs without permission and at an industrial scale. Also, this does not mean Alibaba obtained Claude’s source code, model weights, or original training data. Instead, Anthropic claims the accounts repeatedly asked Claude carefully designed questions and collected the answers. Those answers could then be used as training material for another model. Anthropic has made similar accusations against DeepSeek, Moonshot AI, and MiniMax earlier this year. As Neowin previously reported, Anthropic said those three companies collectively generated more than 16 million Claude exchanges through roughly 24,000 accounts. Anthropic says the new campaign produced almost twice as many exchanges in a matter of weeks. Anthropic reportedly told lawmakers that the campaign could help Chinese AI developers approach the capabilities of its Mythos Preview model. Mythos is focused on advanced cybersecurity work, including finding and exploiting complex software vulnerabilities. via Reuters | Photo via DepositPhotos.com
  • Recent Achievements

    • Rookie
      krychek57 went up a rank
      Rookie
    • Grand Master
      Jaybonaut went up a rank
      Grand Master
    • One Year In
      Philsl earned a badge
      One Year In
    • Dedicated
      Scoobystu earned a badge
      Dedicated
    • First Post
      Tom Schmidt earned a badge
      First Post
  • Popular Contributors

    1. 1
      +primortal
      441
    2. 2
      +Edouard
      175
    3. 3
      PsYcHoKiLLa
      134
    4. 4
      Michael Scrip
      79
    5. 5
      Xenon
      77
  • Tell a friend

    Love Neowin? Tell a friend!