Fans going crazy, CPU 100% idle


Recommended Posts

I'm going insane over the behavior of my 27-inch, medio 2010 iMac. The CPU fan continues to spin up even though the iMac doesn't do a thing. I've reinstalled OS X Lion multiple times, I reinstalled OS X Mountain Lion several times. I did PRAM-resets more times I can count, same goes for SMC resets. Today I even disconnected the iMac, laid it down on my bed and cleared all the vents with the vacuum cleaner on the weakest setting. The other day a friend of mine walked in and immediately asked why my iMac was making so much noise.

The first picture shows the CPU Fan right after startup. The second less than two hours later. I haven't done a thing with the iMac except play music and browse the web a bit.

How on Earth is it possible the fans spin up, sometimes over 4000 rpm, when the CPU sits next to idle most of the time? The worst part is they won't power down once the iMac cooled off. There are no optical drives in the SuperDrive either.

The measurements are in Celsius. The room temperature averaging at 20,5 degrees throughout my apartment. It's only 14 degrees here in Amsterdam.

post-128385-0-15321200-1348764232_thumb.

post-128385-0-38335300-1348764664_thumb.

post-128385-0-02210400-1348765019.png

Link to comment
https://www.neowin.net/forum/topic/1108523-fans-going-crazy-cpu-100-idle/
Share on other sites

assuming your temps are in Celsius it is spinning up because the chip is hot. Is there anything to justify the chip being hot? Dust on the HSF, high ambient temp, etc?

I can't really say for sure how much dust has accumulated inside the iMac itself, but judging by how little there was directly underneath the grill I seriously doubt it's a lot. I tried looking inside with a flashlight but everything seemed clear.

If I leave my iMac on for long periods of time the fans will gradually get faster and faster until they are 100% on, and they will not go back to normal speeds unless I shut down and power back on. Rebooting just keeps them running at full tilt.

It's strange. It's like the driver/sensor controlling it has failed to do it's job properly. :/

Yeah if it's THAT hot at idle, you have a problem on your hands.... either your system has absolutely 0 airflow or the heatsink aint applied correctly, if so I'd take the computer and bring it to a store.

Did you recently install an SSD?

http://forums.macrum...d.php?t=1235234

That actually affects the hard drive fan, not the CPU fan (at least it did in my Late 2010 iMac). Also, it happens a lot sooner than 2 hours after boot. :p

Maybe your GPU is being taxed by something? The CPU fan cools both, so...

Yeah if it's THAT hot at idle, you have a problem on your hands.... either your system has absolutely 0 airflow or the heatsink aint applied correctly, if so I'd take the computer and bring it to a store.

It's an iMac. It's normal for things to run a little bit hotter.

Did you recently install an SSD?

Everything is stock. No modifications whatsoever have been made to the iMac after I unpacked it. Also, the SSD issue wouldn't affect the CPU fan, rather the HDD fan.

Maybe your GPU is being taxed by something? The CPU fan cools both, so...

Okay, this is something I can work with. Is there any way of checking what the GPU load is?

If I leave my iMac on for long periods of time the fans will gradually get faster and faster until they are 100% on, and they will not go back to normal speeds unless I shut down and power back on. Rebooting just keeps them running at full tilt.

It's strange. It's like the driver/sensor controlling it has failed to do it's job properly. :/

That's EXACTLY what ****es me off. The fans won't slow down once things are cooling off.

UPDATE:

Okay this is incredibly interesting. I'm now 100% sure this is indeed a software issue, rather than a hardware related one. For whatever reason OS X Mountain Lion is telling my iMac to increase CPU fan speed in order to cool off. But apparently this is a one-way street. As time progresses the fan speed just continues to go up until it hits a maximum of about 4150 rpm. Like jamesyfx noticed they it will continue running at its maximum until I do a full shutdown. So for whatever reason OS X Mountain Lion won't tell my iMac to reduce fan speeds once it cooled off.

After a lot of Googling I noticed other people having the same issue with OS X Mountain Lion. Not just iMacs but MacBook Pros too. One person came with the suggestion to temporarily download and install iStat Menus 2, set Fan speed control to "Medium" (it's on of the default "rules") and then return to "Default". In literally an instant my iMac's CPU fan would drop from its maximum of ?4150 to a quiet 1940 and then continued to drop.

Check out the below screen shot and note the uptime: Over 6 hours and a regular CPU fan speed of 1885 (it's still dropping as I type).

So what's going on here people?

post-128385-0-90926700-1348790216_thumb.

It does a similar thing on my system, CPU fan speed drops down to a steady 1190rpm when I set to default.

Seems like it kicks the default behaviour back in once you set it as such.

My iMac is a completely different model to yours, so the issue must be software related.. and I think using this utility has proven that.

Yeah that's exactly what seems to happen. iStat basically slaps OS X on the wrist telling it do proper fan control. After a while CPU fans would indeed drop to an average of 1190 rpm on my model as well. Here I was thinking my CPU/GPU fan was constantly triggered because it couldn't handle the new OS X Lion/Mountain Lion graphics effects. But that's not it either.

Anyway, it seems like you can uninstall iStats Menu from your system until you do a SMC reset.

I'm not familiar with Mac since i never owned one but why does OSX has to control the fan ?

I would never ever trust any OS to control the fan speed of my computer. Right now i have a fan controller but if i would not have one i would let my Motherboard control the fan speed or at worst install my MB software (or a 3rd party alternative like speedfan) to control them.

Here's an interesting blog post about the issue. You probably have already read it since it was in the first 10 results of a google search but i still post it just in case.

http://gigaom.com/ap...lion-heres-why/

Spotlight reindexing doesn't take days or weeks.

  • 2 weeks later...

Maybe this helps:

http://www.hddfancontrol.com/

OR:

Symptoms

After plugging in the iMac and turning it on, the fans (blowers) may be noisy and appear to run at full speed. In this event, shutting the iMac off and turning it on again wouldn't fix the issue.

Resolution

If you press the iMac power button while you are inserting the power cord, the iMac will enter a mode in which the fans (blowers) run at full speed. In order to correct the issue, reset the SMC and then start the computer by pressing the power button after the power cord has been fully inserted.

The iMac should now start up and operate as expected.

http://support.apple.com/kb/TS1433

AND:

First download and install smcFanControl 2.2.2. Set it up to provide (still quiet) minimum fan speeds of 2200 rpm for the HD and 2800 rpm for the CPU, leave the Optical Drive fan at 600 rpm to minimize dust accumulation (or just tweak it up if/when you will be using it much) ....

http://hints.macworl...110606033134359

UPDATE:

Okay this is incredibly interesting. I'm now 100% sure this is indeed a software issue, rather than a hardware related one. For whatever reason OS X Mountain Lion is telling my iMac to increase CPU fan speed in order to cool off. But apparently this is a one-way street. As time progresses the fan speed just continues to go up until it hits a maximum of about 4150 rpm. Like jamesyfx noticed they it will continue running at its maximum until I do a full shutdown. So for whatever reason OS X Mountain Lion won't tell my iMac to reduce fan speeds once it cooled off.

After a lot of Googling I noticed other people having the same issue with OS X Mountain Lion. Not just iMacs but MacBook Pros too. One person came with the suggestion to temporarily download and install iStat Menus 2, set Fan speed control to "Medium" (it's on of the default "rules") and then return to "Default". In literally an instant my iMac's CPU fan would drop from its maximum of ?4150 to a quiet 1940 and then continued to drop.

Check out the below screen shot and note the uptime: Over 6 hours and a regular CPU fan speed of 1885 (it's still dropping as I type).

So what's going on here people?

I'm confused. Did that software package end up solving the problem for you or is it still an issue?

Off hand I would say the temp gauges are wrong, without touching the cpu or the motherboard touch the bottom of the heat sink(while the computer is on) and see if its hot. That feels like the CPU is over heating(which would cause the 100% cpu usage).

I have no idea what you're talking about or why you think there is 100% CPU usage. :/

  • 2 weeks later...
  • 2 years later...

Hi there, old thread, but hopefully someone is still around.

I have an iMac 27 late-2009, 3.06 Ghz, 8gb RAM, running OS 10.8.5, and all the hardware is original (no HD swap...). So, it has a similar problem: it takes about an hour for the CPU fan to gradually speed up from the initial approx 1200 RPM to around 4000 RPM. Then, all I have to do is to put it to sleep for enough time to let the fans stop spinning (that's not even 5 seconds) and then wake it up to see the CPU fan at normal speeds. And here it goes for another hour of gradual increase... See the screenshot of the iStats Menu, the graph shows the increase in the last hour, and the three previous increase/sleep patterns... The other two fans are just fine. All of that time, the iMac is at idle, nothing running at all. My iMac isn't my main computer, so i kinda left the problem as it was, spending an hour or so every couple of months trying to solve the issue, but after these 5 years of fruitless efforts, I can't believe I haven't solve it yet! Even though I get answers a lot from forums, here's my first post in one of them (ever!), in hope it will help.

 

Here are the solutions I tried already: smcFanControl, HDD Fan Control, iStats Fan Rules... Nothing seems to be able to override the fan speeds, nothing at all! I vacuumed the air input and output... And of course, I did the SMC reset. I try to remember all the other things I tried to do, but it gets confusing after those years of diverse problem solving. I did many upgrades (and even downgrades) too but I doubt it has anything to do.

 

Even though I never opened the iMac's case (I DID open the bottom latch to replace RAM memory at some point, comes to my mind... but that's not the back case) I wonder if it has anything to do with some hardware that would just be misplaced at the factory of because of a shock while moving the computer around... 

 

Anyone has any idea? Anything I could try?

 

Screenshot:

https://www.dropbox.com/s/vfvkr1zordrbznb/Screen%20Shot%202015-01-14%20at%2011.59.57%20PM.png?dl=0

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Well, it's good to know that they have found a workaround to a problem that they helped create, I guess...
    • Meta is reusing old DDR4 RAM in its servers instead of buying new hardware by Ivan Jenic Image: Meta The global hardware shortage isn’t exactly news, as the entire world has been struggling with rising component prices for quite some time now. And while big companies certainly aren’t as affected as the average consumer, even they aren’t opposed to the idea of saving a few (million) bucks. Meta appears to have found a way to spend less on new hardware while also putting its outdated infrastructure to use, essentially killing two birds with one stone. The company has built a custom chip that lets it reuse memory from retired servers rather than buying new hardware. The chip is called Vistara and allows for connecting old DDR4 RAM from obsolete servers into new servers that rely on DDR5. The problem Vistara solves goes back to a basic mismatch in how long hardware lasts. Meta replaces its servers every three to five years, but the memory modules inside them are good for seven to ten. When a server gets decommissioned, perfectly usable DDR4 RAM goes with it. Meta is presenting the new method at today’s ISCA symposium, but The Register has got hold of a paper that explains how Vistara works. It's a custom ASIC that bridges DDR4 memory to newer processors via aCXL 2.0/1.1 interface over PCIe Gen5 x16. Meta pulls DDR4 sticks from old machines and installs them in dedicated units it calls MemServers, each of which pairs 768GB of DDR5 with 256GB of recovered DDR4. The operating system sees the DDR4 as an additional memory node and draws from it when the primary DDR5 is running low. Off-the-shelf CXL hardware couldn't do this, so Meta built its own. Existing interfaces bundle their own memory with the controller, which makes reusing old RAM sticks impossible. But Vistara separates the controller from the memory entirely, so Meta can plug in whatever DDR4 sticks it has on hand. Meta plans to deploy the new architecture in hyperscale infrastructure with millions of servers, which should mean that Meta’s AI datacenters will now be more efficient. The company is investing heavily in AI infrastructure, especially with its new AI model, Muse Spark, now widely available. All of this doesn't mean that Meta will exclusively rely on "recycled" RAM, but the company is still looking at considerable savings at scale.
    • Save up to 87% on ChatPlayground AI lifetime subscriptions by Steven Parker Today's highlighted deal comes via our Apps + Software section of the Neowin Deals store, where for only a limited time, you can save up to 87% on ChatPlayground AI: lifetime subscriptions. ChatPlayground AI puts the world’s top AI models in one powerful interface, letting you enter a single prompt and instantly compare outputs from multiple models to choose the perfect response for your needs. Boost productivity and creativity with access to the latest AI giants like GPT-4o, Claude Sonnet 4, Gemini 1.5 Flash, DeepSeek V3, and dozens more — all in one window. Whether you’re chatting, coding, generating images, or refining prompts, ChatPlayground AI equips you with advanced tools like prompt engineering, image/PDF chat, saved conversations, and AI image creation, plus priority support to keep your workflow seamless. Access the world’s best AI models Side-by-Side Comparisons: Enter one prompt & instantly view results from multiple AI models to find the best output for your needs 40+ AI Models: Includes GPT-4o, Claude Sonnet 4, Gemini 1.5 Flash, DeepSeek V3, Llama, Perplexity, and many more Multi-Function Platform: Access AI for chat, image generation & coding all within a single interface Web Browser Extension: Offers a Chrome extension to seamlessly integrate the platform into your browsing workflow Boost productivity with powerful features ChatPlayground Interface: Designed for seamless AI model comparison in one window Prompt Engineering: Refine & optimize your prompts for better, more accurate responses Chat with Images & PDFs: Upload visuals and documents to get context-aware answers Saved Chat History: Keep track of past conversations for reference & ongoing projects AI Image Generation: Create high-quality visuals powered by top AI image models Priority Customer Support: Get faster assistance whenever you need it What you'll get with the Unlimited Plan Includes unlimited messages/month Built for prompt engineers, startups, and teams who run experiments nonstop Includes priority access to new features and future models Good to know Length of access: lifetime Redemption deadline: redeem your code within 30 days of purchase Access options: Desktop Max number of device(s): Unlimited Available to both NEW & Existing users Updates included A lifetime subscription to ChatPlayground AI (Unlimited Plan) normally costs $619, but you can pick it up for just $79 for a limited time - that represents a saving of $530 (87% off). Click the link below for more details, always check terms and specifications before making a purchase. Get this ChatPlayground AI (Unlimited) for $79 (was $619) There are also two other discounted plans to choose from. Although priced in U.S. dollars, this deal is available for digital purchase worldwide. Support queries If you have queries or need support for any of the Neowin Deals, please use the contact form here. Neowin Deals are managed and sold by StackCommerce who represent Neowin on an affiliate basis. Why we post these deals We post these because we earn commission on each sale so as not to rely solely on advertising, which many of our readers block. It all helps toward paying staff reporters, servers and hosting costs. So for those that keep moaning and complaining, be thankful we're still online for you to even do that. Other ways to support Neowin Whitelist Neowin by not blocking our ads Create a free member account to see fewer ads Make a donation to support our day to day running costs Subscribe to Neowin - for $14 a year, or $28 a year for an ad-free experience Disclosure: Neowin benefits from revenue of each sale made through our branded deals site powered by StackCommerce.
    • I like Tidal, but it still does not control devices from the mobile/app and still no surround support. And yeah re: above comment I still get a lot of network errors and I am on a 4/4 Gbit Fiber connection.
  • Recent Achievements

    • Reacting Well
      NovaEdgeX earned a badge
      Reacting Well
    • Week One Done
      NovaEdgeX earned a badge
      Week One Done
    • One Year In
      BA the Curmudgeon earned a badge
      One Year In
    • Conversation Starter
      rosiecharles earned a badge
      Conversation Starter
    • First Post
      KMilenkoski1202 earned a badge
      First Post
  • Popular Contributors

    1. 1
      +primortal
      539
    2. 2
      +Edouard
      266
    3. 3
      PsYcHoKiLLa
      151
    4. 4
      Steven P.
      98
    5. 5
      macoman
      66
  • Tell a friend

    Love Neowin? Tell a friend!