Issue with formatting a secondary drive in Windows 8


Recommended Posts

Hi all,

i'm having a small issue with formatting a secondary drive in Windows 8.

I have been experiencing sluggish performance with this drive which was being used as a software backup, I backed up all the data on the drive a proceeded to format the drive in computer management, but the drive in question is listed as a system partition and won't let me format it for obvious reasons.

I no idea why a secondary drive has been selected as the system partition, what I would like to know is there a way to move the system partition or do I have to reinstall Windows 8.

As you can see from the screenshot, the F drive is shown as System (Active) this is the drive I cannot format

post-149938-0-15539900-1357756091.png

If that drive is set as 1st disk (Disk 0 ) in the BIOS / SATA port, then no matter which drive you install windows on, it will always use disk 0 for the MBR

No, My primary drive is on the 1st SATA port and always has been, there is no way to configure the drive in the bios other than choosing which device boots first which was my Blu-Ray drive then my primary HDD.

No, My primary drive is on the 1st SATA port and always has been, there is no way to configure the drive in the bios other than choosing which device boots first which was my Blu-Ray drive then my primary HDD.

I would physically unplug it from the board and see if you can boot

If you can. just use disk management to delete the partition and format the drive

I would physically unplug it from the board and see if you can boot

If you can. just use disk management to delete the partition and format the drive

I can't use disk management to format the drive, when I attempt to do this it says "Windows cannot format the system partition on this disk"

You can use Diskpart to do it.

1. Type "diskpart" on the Start screen, then right-click it in the results and run it as an administrator.

2. Type "list disk" to get a list of the drives on your system, then find the one you want to erase. (Double-check this!)

3. Type "select disk X" where X is the drive number from the previous command output.

4. Double-check TWICE that you selected the right drive as Diskpart will not ask for confirmations.

5. Type "list partition" and verify again it's the right drive.

6. Repeat step 4. :)

7. Type "clean"

This will wipe all the partition information from the drive and you should be able to partition and format it in Disk Management.

You might want to switch to the proper disk before step 5 and use the "active" command to mark it so.

With your primary system partition showing as F it is possible you may find your system in an unbootable state so make sure you have a way to recover if necessary.

"You have to delete the partition before formatting"

what?? You format a partition, you can not format a non partitioned disk.

Now he may will delete the partition, and then just create a new one and then format that. But your wording is odd if that was what you meant to say.

Follow greywolf instructions and you should be good.

"You have to delete the partition before formatting"

what?? You format a partition, you can not format a non partitioned disk.

Now he may will delete the partition, and then just create a new one and then format that. But your wording is odd if that was what you meant to say.

Follow greywolf instructions and you should be good.

Yea, well he is saying he can't format the system partition, so he would have to delete it first if it won't let him format it, and yea then make a new one

Yea I see what you are saying, if he deleted it he would have no need to format it after creating a new one - should have excluded the formatting thing and just left "You need to delete the partition"

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • We had no idea as kids how much time and energy it took to be an adult 😅
    • The Trump administration doesn't want you to use OpenAI's GPT-5.6 without its approval by David Uzondu Image via @realDonalTrump (X) As OpenAI prepares the release of its next model, GPT 5.6, the White House has instructed the company to limit the distribution of the software to a small group of government-approved partners instead of the general public, as it has done with previous releases. According to The Information, OpenAI Chief Executive Officer Sam Altman sent an internal memo to staff on Thursday explaining that the federal government will approve access "customer by customer" during an initial preview phase. Altman noted in the communication that this restrictive rollout is "not [their] long-term model" for software deployment, and the company plans to work toward a "more sustainable" distribution method later. CNN said that both OpenAI and the Trump administration view the capabilities of GPT 5.6 on the same level as Anthropic's Mythos and that government officials intend to "collaborate with frontier AI labs to develop shared approaches for addressing the challenges of scaling this technology." The latest restriction comes just weeks after the US Commerce Department decided to restrict Fable, a version of Mythos with extra safety "guardrails" to prevent users from exploiting software vulnerabilities. Not long after the release, though, researchers at Amazon found a way to bypass these restrictions, prompting an aggressive response from federal authorities. The government ordered Anthropic to cut off access for non-US citizens located outside the US, non-US citizens living inside the US, and incredibly, even Anthropic's own foreign-born employees. Anthropic now appears to be building a workaround to resolve this compliance block with an update to its Privacy Policy that introduces a category called "Verification Data" to handle KYC and Digital IDs. This setup could mandate digital identity checks to filter users by nationality, requiring a government-issued ID and facial biometric data. Who knows? Maybe in the future, you would have to scan your US Passport or State ID to prove your citizenship before you are allowed to chat with Fable 5 (or any other model).
    • When Windows 7 was released I created an AutoHotkey script that uses Alt+` as a keyboard shortcut to move a window across monitors. I have been using that script for over 15 years and this is the first time I have come across another app that uses the same shortcut!
  • Recent Achievements

    • Week One Done
      xvvxcvv earned a badge
      Week One Done
    • One Month Later
      xvvxcvv earned a badge
      One Month Later
    • Enthusiast
      Xonos went up a rank
      Enthusiast
    • Conversation Starter
      Admir earned a badge
      Conversation Starter
    • First Post
      The_Focal_Point earned a badge
      First Post
  • Popular Contributors

    1. 1
      +primortal
      403
    2. 2
      +Edouard
      172
    3. 3
      PsYcHoKiLLa
      127
    4. 4
      neufuse
      69
    5. 5
      Steven P.
      67
  • Tell a friend

    Love Neowin? Tell a friend!