Recommended Posts

Okay so I was trying to change my IP Address by doing the following:

1. Open CMD

2. Type in 'ipconfig/release'

3. Go into Network Settings

4. Click on Properties for IPv4

5. Type in my own IP Address and DNS Server and Save

6. Go back into IPv4 Properties but check off the 'Obtain New IP Address' box and then Save

But after step 6, my IP Address is the same. Also, I have a Dynamic IP Address I think because when I open CMD and type in 'ipconfig/all', next to DHCP Enabled, it says Yes. I

If anything, please help guys! Thanks!

Edit: I'm Also running on Windows 7. Thanks!

Link to comment
https://www.neowin.net/forum/topic/1056134-how-do-i-change-my-ip-address/
Share on other sites

are you wanting to change your IP from your Internet provider or just the Local Network ?

Local Network, you would have to manually change it to something else, as the DHCP will just reassign you the lowest number, and if you have a small amount of systems, it will mostly be teh same.

Internet - turn off your Modem, wait for about 5-10 minutes, then turn it back on ( time is dependant on your providers DHCP renewal cycle, which isnt exact and sometimes days

which IP do you want to change? (reboot the modem but your IP has a life expectancy dictated by your ISP) ..

you can call them and ask to release a new IP

(if you want to change your LAN (internal IP then relase and go to router and give yourself a new one)

Maybe I'm a moron, but isn't your Dynamic IP address set by your Internet Service Provider? I don't think you can just type in your own.

there are 2 IP's, Local and Public, the Public is set by your provider, tne Local is Private and set by your router and is usually in the Popular 10.X.X.X, or 192.X.X.X range, or not so familiar 172.16.X.X

but yes being Dynamic is set by something else and rotates based on a lease time, but i still have yet to figure out when exactly that lease time goes into effect, as it doesnt follow the setting

are you wanting to change your IP from your Internet provider or just the Local Network ?

Local Network, you would have to manually change it to something else, as the DHCP will just reassign you the lowest number, and if you have a small amount of systems, it will mostly be teh same.

Internet - turn off your Modem, wait for about 5-10 minutes, then turn it back on ( time is dependant on your providers DHCP renewal cycle, which isnt exact and sometimes days

I would like to change my Local Network connection. Any steps or ideas of how to do it? Thanks. :)

Maybe I'm a moron, but isn't your Dynamic IP address set by your Internet Service Provider? I don't think you can just type in your own.

I have called them and they said that I have a dynamic IP Address.

Your Internet address is set by your ISP. You'd have to call them to ask them to change it.

Tried that. Doesn't work that way.

Your ISP administer IP address allocation and unless you have a static IP address you can't influence this other than rebooting your modem/router to see if they've supplied you with a new one.

If you're talking about your local IP address then turn off DHCP in your router to enable you to explicitly control IP address allocation.

Your ISP administer IP address allocation and unless you have a static IP address you can't influence this other than rebooting your modem/router to see if they've supplied you with a new one.

If you're talking about your local IP address then turn off DHCP in your router to enable you to explicitly control IP address allocation.

Yes, I am talking about my local ip address. Thanks :)

I would like to change my Local Network connection. Any steps or ideas of how to do it? Thanks. :)

the steps you were doing semed right up til you reenabled DHCP, and literally there is no reason to reassign your Local IP address.

but log into your router, disable DHCP of the LOCAL ONLY, NOT INTERNET CONNECTION DHCP

on your computer go to Network Setting properties for IPV4

set it to whatever in the range of the router ( in the image the rage for example would be 192.168.1.101-192.168.1.149, its the Router Starting+1, and Clients -1, so 101-149 )

save and your done

by reinabling DHCP you undid the setting of the IP

this is the setting your looking for

post-36462-0-26883300-1328457810.jpg

* Can i ask why you want to change your Local. there is no reason to at all

the steps you were doing semed right up til you reenabled DHCP, and literally there is no reason to reassign your Local IP address.

but log into your router, disable DHCP of the LOCAL ONLY, NOT INTERNET CONNECTION DHCP

on your computer go to Network Setting properties for IPV4

set it to whatever in the range of the router ( in the image the rage for example would be 192.168.1.101-192.168.1.149, its the Router Starting+1, and Clients -1, so 101-149 )

save and your done

by reinabling DHCP you undid the setting of the IP

this is the setting your looking for

post-36462-0-26883300-1328457810.jpg

* Can i ask why you want to change your Local. there is no reason to at all

Well actually, I have tried that but I don't think it worked. Hmm maybe I need someone to Team Viewer me or something? Also, I'm not sure if I want to change my Local Internet Connection but I want to change the connection so that when I go to http://www.whatismyip.com/ , it would display another IP Address other than the one that I already have.

You don't have a antivirus that prevents network connection changes do you?

Start > Control Panel > Network and Sharing > Change Adapter Settings

Unplug your network connection (if wired) or disable wireless (switch)

Right click connection > Properties

IPv4 > Properties

Use the following IP address:

Set the IP address you want: eg 192.168.1.56

Subnet 255.255.255.0

Default Gateway: Address of your router (eg, 192.168.1.1)

Press ok and close everything else with "ok"s, not X's

Now since it hasn't been working so well for you, reboot, log in, check that the settings are still present, and then plug in your network connection.

By the way, what has been telling you your IP address hasn't changed?

Edit: Ok I just saw your latest post. "Whatismyipaddress" shows your INTERNET, public address, which is controlled by your ISP. If you have a dynamic IP, turn your modem off for an hour or so... really depends on how long your lease is for. Overnight might be best.

Well actually, I have tried that but I don't think it worked. Hmm maybe I need someone to Team Viewer me or something? Also, I'm not sure if I want to change my Local Internet Connection but I want to change the connection so that when I go to http://www.whatismyip.com/ , it would display another IP Address other than the one that I already have.

You tried that but redid the automatic when you reinabled DHCP, causing it to undo everything

And whatismyip shows your PUBLIC IP, and you cant manually vhange that other then turning off you modem for a long time

You don't have a antivirus that prevents network connection changes do you?

Start > Control Panel > Network and Sharing > Change Adapter Settings

Unplug your network connection (if wired) or disable wireless (switch)

Right click connection > Properties

IPv4 > Properties

Use the following IP address:

Set the IP address you want: eg 192.168.1.56

Subnet 255.255.255.0

Default Gateway: Address of your router (eg, 192.168.1.1)

Press ok and close everything else with "ok"s, not X's

Now since it hasn't been working so well for you, reboot, log in, check that the settings are still present, and then plug in your network connection.

By the way, what has been telling you your IP address hasn't changed?

I will let you know how that goes as I've been doing that but I will use the numbers you have supplied me with. And this website has been telling me that my IP Address hasn't changed: http://www.whatismyip.com/

You don't have a antivirus that prevents network connection changes do you?

Start > Control Panel > Network and Sharing > Change Adapter Settings

Unplug your network connection (if wired) or disable wireless (switch)

Right click connection > Properties

IPv4 > Properties

Use the following IP address:

Set the IP address you want: eg 192.168.1.56

Subnet 255.255.255.0

Default Gateway: Address of your router (eg, 192.168.1.1)

Press ok and close everything else with "ok"s, not X's

Now since it hasn't been working so well for you, reboot, log in, check that the settings are still present, and then plug in your network connection.

By the way, what has been telling you your IP address hasn't changed?

Edit: Ok I just saw your latest post. "Whatismyipaddress" shows your INTERNET, public address, which is controlled by your ISP. If you have a dynamic IP, turn your modem off for an hour or so... really depends on how long your lease is for. Overnight might be best.

You tried that but redid the automatic when you reinabled DHCP, causing it to undo everything

And whatismyip shows your PUBLIC IP, and you cant manually vhange that other then turning off you modem for a long time

Thank you guys! Here is my settings for my modem:

0CAuV.png

Does anyone know how long I have to wait for a new IP Address? Thanks,

You might have to wait forever.. All depends on your ISP,

The can try and force the change by changing the mac on the wan interface of your router - does your router support mac cloning? What is the specific model of your router your showing there?

Then again what do you think your going to accomplish changing your public IP?? I would guess your trying to circumvent some sort of block? This is really the only reason to do such a thing.

You might have to wait forever.. All depends on your ISP,

The can try and force the change by changing the mac on the wan interface of your router - does your router support mac cloning? What is the specific model of your router your showing there?

Then again what do you think your going to accomplish changing your public IP?? I would guess your trying to circumvent some sort of block? This is really the only reason to do such a thing.

In which case, it would probably just be easier to use a proxy!

In which case, it would probably just be easier to use a proxy!

No proxies are slow and not useful.

You might have to wait forever.. All depends on your ISP,

The can try and force the change by changing the mac on the wan interface of your router - does your router support mac cloning? What is the specific model of your router your showing there?

Then again what do you think your going to accomplish changing your public IP?? I would guess your trying to circumvent some sort of block? This is really the only reason to do such a thing.

This is my exact router:

http://www.motorola.com/Consumers/US-EN/Consumer-Product-and-Services/Cable-Modems-and-Gateways/SBG6580-SURFboard-eXtreme-Wireless-Cable-Modem-Gateway-US-EN

If you are wanting to change your IP address set by your ISP, you will just have to wait for your ISP to change it. No other option short of using a proxy.

If you are talking about your local IP, the 192.168..... , then turn off DHCP (in your router) and set your IP address in your network connection:

Control Panel\Network and Internet\Network and Sharing Center > click "Local Area Connection" > Properties > Internet Protocol Version 4 (TC{/IPv4) > Properties

Does anyone know how long I have to wait for a new IP Address? Thanks,

Just install Hotspot Shield and call it a day?

Most ISPs will probably assign your account to a single IP address, and then your modem/router will distribute that ip address across the local network. You aren't going to get very far in trying to change your ip address. Spoofing is illegal, so the only alternative is to use a proxy service that will redirect all your data through a separate server that has a different ip address (and yes, whatismyip.com will show the new ip address).

This topic is now closed to further replies.
  • Posts

    • Can you still click his nose in the about box?
    • In that case this product has no value to me. I'd rather use older Creative SB that were better in my opinion or onboard audio chip.
    • FxSound 1.2.9.0 / 1.2.10.0 Beta by Razvan Serea FxSound (formerly DFX Audio Enhancer / FxSound Enhancer) is now free, making high-quality audio enhancement accessible to everyone. Designed for all PC sound systems, from average setups to audiophile-grade equipment, it offers automatic or fully customizable processing. As automatic or customizable as you want, it utilizes the highest-grade processing to deliver more volume, better equalization, and a wider, deeper sound. For the serious audiophiles, FxSound gives you the tools to adjust the FxSound Effects and EQ to your exact preferences. Turn FxSound on and immediately hear the difference in sound quality. FxSound is ideal for budget audiophiles, music lovers, gamers, transcriptionists, Netflix enthusiasts, and more. It’s particularly beneficial for those relying on quiet laptop speakers or low-quality audio hardware. As a free tool, FxSound excels in boosting volume, enhancing bass, and improving sound quality. No other free EQ for Windows matches its ease of use. FxSound Is Now Completely Free and Unrestricted FxSound Pro is now free for everyone, not just those who can afford it. Get free and unrestricted access to better sound today. FxSound is now entirely supported by users. Click here to donate to help fund continued development and improvements to FxSound. FxSound 1.2.9.0 changelog: Auto save preset when Equalizer or Effects settings are changed Reset to factory defaults can reset the unsaved preset changes Settings dialog UI improvements for Audio and Equalizer sections Output device list is now displayed in the device preference order Preset is selected immediately when the preset for an active output device changes from settings Fixes and improvements in preferred output device selection Fixed crash issue #487 Fixed preset not getting applied and EQ flat after update (#403 and #472) Fixed system audio device not being restored on reboot (#483) Fixed preset export and import dialogs not shown when always on top is enabled Fixed audio not being restored on exit after the preset save dialog Fixed FxSound on/off handling on Windows session changes FxSound 1.2.10.0 Beta changelog: Command line options can now be applied to an already running instance of FxSound Command line option added to launch FxSound minimized to the system tray Fixed output device not being changed through hotkeys when FxSound is off (#524) Individual hotkeys can now be disabled with Delete key (#515) Fixed the but to prevent invalid hotkeys from being registered (#523) Bluetooth devices removed from device settings are removed from device preference list Fixed device detection failures Fixed application hang when retrieving the audio mix format fails Fixed presets import dialog file name combo box text alignment Fixed output device not being applied through command line Fixed a delay blocking application load when minimizing to the system tray Fixed EQ band sliders not refreshing when switching number of bands (#521) Fixed user-set mute being overridden by FxSound Fixed icon visibility in ARM64 version Finnish language support added Corrected Persian translations Download: FxSound 1.2.9.0 | ARM64 | ~70.0 MB (Open Source) Download: FxSound 1.2.10.0 Beta | ARM64 View: FxSound Home Page | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • mIRC 7.84 Final by Razvan Serea mIRC is a full featured Internet Relay Chat client for Windows that can be used to communicate, share, play or work with others on IRC networks around the world, either in multi-user group conferences or in one-to-one private discussions. It has a clean, practical interface that is highly configurable and supports features such as buddy lists, file transfers, multi-server connections, SSL encryption, proxy support, UTF-8 display, customizable sounds, spoken messages, tray notifications, message logging, and more. mIRC also has a powerful scripting language that can be used both to automate mIRC and to create applications that perform a wide range of functions from network communications to playing games. mIRC has been in development for over a decade and is constantly being improved and updated with new technologies. mIRC 7.84 changelog: Added custom dialog editbox option 'optional' for grayed out optional text. Fixed DirectShow temporary wave file not being deleted on exit. Changed $urlget() to retry a connection without compression in the event of an error. Updated code signing certificate to use Azure Artifact Signing. Fixed menubar display bug when in dark mode. Fixed /server -a not preserving existing entry's codepage. Fixed Address Book nick colors "idle time" display bug. Changed installer to no longer require administrator access on startup. Added support for displaying an MDI window's System menu when right-clicking its titlebar. Updated libararies to OpenSSL v3.5.7, TagLib v2.2.1, Zlib v1.3.2, and ADA v0.5.5. Updated CA root certificates cacert.pem file. For a full list of recent changes, please see the versions.txt file. Download: mIRC 7.84 | 4.3 MB (Shareware) View: mIRC Home Page | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • You might be right... Look at his name, hiding in plain sight: hAmId.
  • Recent Achievements

    • One Month Later
      timbobit earned a badge
      One Month Later
    • One Month Later
      nates earned a badge
      One Month Later
    • Week One Done
      Almohandis earned a badge
      Week One Done
    • Rookie
      dorf went up a rank
      Rookie
    • First Post
      mike_rumble earned a badge
      First Post
  • Popular Contributors

    1. 1
      +primortal
      470
    2. 2
      +Edouard
      165
    3. 3
      PsYcHoKiLLa
      106
    4. 4
      Michael Scrip
      87
    5. 5
      Steven P.
      69
  • Tell a friend

    Love Neowin? Tell a friend!