Power Supply Dying?


Recommended Posts

I have an Antec SP500 500W power supply that I got in 2006 when I built my desktop (specs in sig.) I haven't had any problems with it until now. Today, the power supply has started making a really high-pitched whining noise. It's defiantly the power supply (placing my ear right up next to the back of it is the loudest). While the PC is powered on, the noise is constant, and it persists for a little while after shutting down. If I put the computer to sleep, the noise alternates between a high pitch and a slightly lower pitched noise and then subsides after a while. During this period, after shutting down, if I pull the power plug from the back of the unit, the noise stops, likewise it does if I flip the switch on the back. I haven't noticed any other power-related issues, but this high-pitched noise is really annoying and I think actually gave me a headache today. I guess it's time to replace the unit?

Link to comment
https://www.neowin.net/forum/topic/1059644-power-supply-dying/
Share on other sites

from the way your descibing it it sounds like a fan in the psu is going ...why risk it? replace it before you have the replace a lot such as a motherboard if the psu blows

I second this, only I press it further, (with plenty of luck)....I always replace a dead power supply fan with a new fan when I hear that fan squeal...or what else I've found, and I'm not joking here...is that KY massage oil usually (if applied sparingly to ONLY the fan bearings, let sit a while, turn by finger (no pun intended)....and those stuck fans will usually free themselves....just MAKE SURE you've properly discharged the capacitors (again, no pun intended) from the power supply...google can help you there...also....wait for the oil to seep into the bearing/bushing...then cover the back with a fresh little strip of duct tape....make SURE you wipe up any excess oil...I.E., do NOT let it drip....ANYWHERE or touch ANY wires....if you use a push-pin, or a baby pin, and put about three dabs of it into the bearing/bushing, ..it can end up okay. I have done this on I can't tell you how many fans that have been ruined...well, almost....in this west-texas dust....power supply, case fans....even a graphics card, although it was so meticulous, it scared me, lol! But it is possible....just not advisable. :shiftyninja:

Thanks everyone. I don't really feel comfortable with opening up a power supply just to lube up a fan. I've always heard the warnings about not opening up a power supply and I had a bad experience with a capacitor when I was a kid trying to take apart a camera. Ever since then, I haven't taken them lightly. I'd rather buy a new power supply than shock myself. Anyone have any recommendations for a decent ~500W power supply for about ~$50 or less?

It doesn't sound like a fan issue anyway. A high pitched sound usually means a MOSFET is on it's way out or already dead. It would just be a matter of time before it dies completely.

Just a random guess, but your voltage rails might not be at the levels they should be, so your motherboard and other components might be at risk if this is true.

But yeah, hurry up and get that PSU replaced.

Thanks everyone. I don't really feel comfortable with opening up a power supply just to lube up a fan. I've always heard the warnings about not opening up a power supply and I had a bad experience with a capacitor when I was a kid trying to take apart a camera. Ever since then, I haven't taken them lightly. I'd rather buy a new power supply than shock myself. Anyone have any recommendations for a decent ~500W power supply for about ~$50 or less?

Your gonna struggle to find a high quality 500W PSU for $50...just filtering on newegg http://www.newegg.com/Product/Product.aspx?Item=N82E16817171031 is the only one I'd suggest.

If you can afford a bit more in the 50-75 range there are some good ones, including this Corsair one http://www.newegg.com/Product/Product.aspx?Item=N82E16817139027

It doesn't sound like a fan issue anyway. A high pitched sound usually means a MOSFET is on it's way out or already dead. It would just be a matter of time before it dies completely.

Just a random guess, but your voltage rails might not be at the levels they should be, so your motherboard and other components might be at risk if this is true.

But yeah, hurry up and get that PSU replaced.

I agree, it doesn't sound like a fan issue at all... especially for the fact that it is still whining after you power off.

Even though i would still replace it, i would recommend you clean your components, because dust build up can harm your components, most likely the case here.

if that's the same noise i heard on my old Emachines PC it's sort of faint but you can definitely hear it and it also stopped once i unpluged it or hit the switch. but that PC don't see much use anymore and it's not a standard PSU in it etc so i just did not worry about it. but as others have said... if you got some spare $$$ it could not hurt replaceing it now before it possibly gets worse.

but on my current PC my PSU ended up giving me some warnings like turning off and not wanting to turn on etc etc before it got to the point i just said the hell with it and got a replacement (but it eventually completely died before i ordered a new one though as it would not turn on at all). it was a shame as i had that PSU for roughly 4 years and it was $109.99 new (back in March 2006) and it was a Enermax Liberty 500watt PSU. my replacement is a 630watt Rosewill which i got for about $60 back i think in about mid-2010,

p.s. i generally leave my PC on 24/7.

  • 4 months later...

Sorry to bump this, but, it finally died today. Had the PC powered off for a few days while I was on vacation and when I flipped the switch on the PSU and hit the button to power on the PC, it stuttered (heard the fans try to power up and the case lights flickered. Shortly thereafter, I smelled a burning smell. Just hope nothing aside from the PSU is fried. If so, I'm not too concerned; it's an excuse for me to make some upgrades which are long overdue.

I think that I may need more than just a new power supply now. I tested a known working 350W supply with the computer and after connecting just the 24-pin power connector and 4-pin power connector to the motherboard, nothing happens when hitting the power button. I probably should've replaced the poser supply before it blew. :/

Yes... Yes you should have. Just as everyone had stated previously.

I know that high pitched noise all too well, and it should persist even with the computer turned off, so long as the PSU is plugged into power.

Once that starts up, you should buy a new PSU the next day because you never know when it'll decide to die after that point.

I have an Antec SP500 500W power supply that I got in 2006 when I built my desktop (specs in sig.) I haven't had any problems with it until now. Today, the power supply has started making a really high-pitched whining noise. It's defiantly the power supply (placing my ear right up next to the back of it is the loudest). While the PC is powered on, the noise is constant, and it persists for a little while after shutting down. If I put the computer to sleep, the noise alternates between a high pitch and a slightly lower pitched noise and then subsides after a while. During this period, after shutting down, if I pull the power plug from the back of the unit, the noise stops, likewise it does if I flip the switch on the back. I haven't noticed any other power-related issues, but this high-pitched noise is really annoying and I think actually gave me a headache today. I guess it's time to replace the unit?

I used to have one of those. Its a sign its dying. The capacitors are most likely swollen. I believe that sound is the power output coil.

I no longer buy Antec. I warrantied mine and they sent me another with the same crappy capacitors. The replacement died after a year.

Go buy something like Corsair, Seasonic, or anything with a PLUS 80 rating.

BTW I have never seen a PSU cause damage to a mainboard from failing. I repair PSU all the time for the company I work for and I am also a computer tech on the side. Seen many cheap chinese power supplies blow and never had to replace a board because of it.

Shorting the PS_ON/COM (I use a paper clip) on the 24pin mobo cable (obviously not while connected to PC) will run it independently of the PC and confirm if it's the PSU or something else. It's most likely the fan's ball bearings as others have said. If it is the fan, it can be changed, or you can get a new PSU.

I'm at a loss here. I have basically disconnected everything from the motherboard except for the processor, RAM, connectors for the power/reset button, and obviously the power cable. The known working power supply that I'm testing with is a 350W. May this not be powerful enough for my motherboard and that's why it's not working? Furthermore, I've noticed that there are three bulging capacitors on the video card (a 256 MB ATI Radeon x700). Could this have been caused by the original power supply failing?

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Microsoft finally admits its default Windows 11 25H2, 24H2 action broke key legacy component by Sayan Sen Microsoft last week released Windows 11 KB5094126 and KB5093998 as the latest Patch Tuesday updates. Following that the company also published the accompanying dynamic updates under KB5094149, KB5095971, and KB5094156. So far the company has acknowledged two known issues that have popped up after the release which include bugged-out Office apps as well as the Recycle Bin; though there could be more at play too. Speaking of bugs and issues, Microsoft seems to have finally acknowledged a problem that probably has been around for close to a year. That's because back in July of 2025 the company made a default change to the latest Windows 11 versions, wherein it switched to JScript9Legacy on Windows 11 24H2 and later releases. Hence following the release of version 25H2 in October 2025, JScript9Legacy also remained default-enabled. As a result there has been a compatibility issue ever since then. For those wondering, by switching to JScript9Legacy Microsoft intended to improve the security of modern Windows PCs by reducing vulnerabilities tied to legacy scripting like cross-site scripting (XSS), among others. XSS exploits can allow cyber-attackers to attach malicious code onto legitimate websites and use them to execute the code when a potential victim loads such a website. Hence the new JScript9Legacy engine enforced stricter execution policies and improved object handling, which should help mitigate such attacks. Microsoft today has published a new support article detailing the problem. Neowin spotted it while browsing. The company says that JScript global definitions and execution context may fail to persist across scripts, potentially breaking older dependent apps and web-based components that relied on this legacy behavior. In the article Microsoft has confirmed that the issue stems from its move away from the older jscript9.dll engine in favor of jscript9legacy.dll. As mentioned above, while the newer engine was designed to address vulnerabilities and strengthen security it also changes how JScript handles execution context. As a result functions and definitions loaded by one script could no longer remain available to subsequent scripts once execution ended. The company notes that some applications worked correctly on earlier Windows versions because the older JScript engine automatically retained global definitions and execution state between scripts. Under the newer model though that behavior is disabled by default causing certain legacy workloads and polyfill-dependent scripts to fail. Microsoft says it addressed the problem via the KB5077241 update though the fix had not been enabled automatically in the following updates. As such admins must explicitly turn on persistent JScript execution context using a Registry setting that the tech giant shared today. The configuration can be applied to individual processes or system-wide through the FEATURE_ENABLE_PERSISTENCE registry key. The steps have been outlined below: Run the following command to create the feature control registry key: reg add "HKLM\Software\Policies\Microsoft\Internet Explorer\Main\FeatureControl\FEATURE_ENABLE_PERSISTENCE" Under this key, create a new DWORD (32-bit) value. Configure the value as follows: To enable persistence for specific processes only: Set the value to 1 for each target process name. To enable persistence for all processes: Add * as the key name and set its value to 1. You can find the official support article here on Microsoft's website.
    • The possibility that milk gathers back into a glass implies that gravity can be 'reversed'.
    • VidCoder 12.20 by Razvan Serea  VidCoder is a DVD/Blu-ray ripping and video transcoding application for Windows. It uses HandBrake as its encoding engine. Calling directly into the HandBrake library gives it a more rich UI than the official HandBrake Windows GUI. VidCoder can rip DVDs but does not defeat the CSS encryption found in most commercial DVDs. You’ll need the NET 8 Desktop Runtime. If you don’t have it, VidCoder will prompt you to download and install it. The Portable version is self-contained and does not require any .NET Runtime to be installed. You do not need to install HandBrake for VidCoder to work. Feature list: Multi-threaded MP4, MKV containers Completely integrated encoding pipeline: everything is in one process and no huge intermediate temporary files H.264, H.265, MPEG-4, MPEG-2, VP8, Theora video Hardware-accelerated encoding with AMD VCE, Nvidia NVENC and Intel QuickSync AAC, MP3, Vorbis, AC3, FLAC audio encoding and AAC/AC3/MP3/DTS/DTS-HD passthrough Target bitrate, size or quality for video 2-pass encoding Decomb, detelecine, deinterlace, rotate, reflect, chroma smooth, colorspace filters Powerful batch encoding with simultaneous encodes Customizable Pickers to automatically pick audio and subtitle tracks, destination, titles and more Instant source previews Creates small encoded preview clips Pause, resume encoding VidCoder 12.20 changes: Updated HandBrake core to 1.11.2. Download: VidCoder 12.20 | 47.0 MB (Open Source) Download: Portable VidCoder 12.19 | 89.3 MB Link: VidCoder Home Page | Github | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • Too soon, I'm still not over this death!
  • Recent Achievements

    • Week One Done
      Jordan Smith earned a badge
      Week One Done
    • Reacting Well
      BizSAR earned a badge
      Reacting Well
    • First Post
      AndreaB earned a badge
      First Post
    • Week One Done
      Huge Trailer earned a badge
      Week One Done
    • Week One Done
      Classifyskilleducation earned a badge
      Week One Done
  • Popular Contributors

    1. 1
      +primortal
      593
    2. 2
      +Edouard
      185
    3. 3
      PsYcHoKiLLa
      76
    4. 4
      Michael Scrip
      73
    5. 5
      Steven P.
      66
  • Tell a friend

    Love Neowin? Tell a friend!