[Windows 7] Install cannot see drive


Recommended Posts

Hi Guys,

Need some help as my jet-lag riddled brain cannot figure this out.

One of my PC's seems to have had a bit of a time of it during moving house. One of 2 hard drives has failed, previously in a striped RAID configuration. The other drive appears okay, no SMART errors, and detected by the BIOS. I've removed the defective drive, disabled RAID, and attempting to install Windows 7 just on that one drive.

The BIOS can see the drive plugged in to SATA port 3 just fine, however the Windows 7 installer refuses to detect the drive at all. Any thoughts on why this might be?

This is an older machine, running on an Asus A8N32-SLI Deluxe motherboard, which is an nForce 4 chipset.

Can anybody point me in the right direction?

Thanks

Link to comment
https://www.neowin.net/forum/topic/1084801-windows-7-install-cannot-see-drive/
Share on other sites

Thanks for the help so far guys - to answer some of the points:

Do you have a sata drive on the win 7 install software?

If memory serves press F6 at boot and install the driver from the motherboard CD if it doesnt

Theoretically, it shouldn't need it. The motherboard is an nForce 4 chipset which, as far as I know, is supported natively.

can you see the drive in computer management? it may just be a case of windows has not mounted the drive.

Alas, courtesy of the other drive in the RAID array failing, I can't even boot windows (it was set to Striped mode). What I'm trying to do now is disable RAID entirely and just flat install it on to this disk that used to be part of the RAID array.

Just had the same problem as my SSD card is RMAd in holland. I had to set the harddrive to active in Win 7 setup before Windows would let me install on it.

How did you do that exactly?

Thanks, but unfortunately my motherboard has no driver that needs to be loaded before install :(

You need to download the RAID Controller drivers from the boards manufacturers site, extract them and put them on a FAT32 flash drive

When you reach the drive selection screen, hit the browse for drivers button and point it to the RAID Controller drivers you downloaded

Since you had a raid0 and lost one drive it will not boot until you rebuilt your raid array. Also all your data is gone so I hope you performed backups. Go into the onboard raid controller on post and delete your existing raid array and recreate a new one with both drives. Either raid0 or raid1, if you go raid0 again, buy a backup drive. Once this is done boot into windows 7 and it should show as one phycisal volume and simply install Windows 7. If Windows 7 does not see the volume then using a flash drive, download the motherboard raid controller drivers and extract them, Select the driver at the Windows 7 installer screen and the hard drive should appear.

And to add I have had that same motherboard and I had the SATA ports fail on it one day out of the blue. I was also running raid0 on that mobo and also disabled the raid controller to test out what was going on. The bios detected the drives but Windows 7 would not see the drives and or would sometimes lockup at the Windows 7 install screen. After flashing the firmware, resetting the bios I had no luck so I just bought a new mobo. There is no official support for nForce4 from Nvidia for Windows 7 so the drivers for the raid array are most likley included in the Windows 7 iso image.

Since you had a raid0 and lost one drive it will not boot until you rebuilt your raid array. Also all your data is gone so I hope you performed backups. Go into the onboard raid controller on post and delete your existing raid array and recreate a new one with both drives. Either raid0 or raid1, if you go raid0 again, buy a backup drive. Once this is done boot into windows 7 and it should show as one phycisal volume and simply install Windows 7. If Windows 7 does not see the volume then using a flash drive, download the motherboard raid controller drivers and extract them, Select the driver at the Windows 7 installer screen and the hard drive should appear.

He said he already disabled RAID and is trying to use it as a single drive

@Detection I noticed that

You need to download the RAID Controller drivers from the boards manufacturers site, extract them and put them on a FAT32 flash drive

When you reach the drive selection screen, hit the browse for drivers button and point it to the RAID Controller drivers you downloaded

He said already that he disabled RAID and is trying to use it as a single drive

Get over it dude, just trying to help...

Try a diskpart on the drive

http://www.google.co.uk/search?q=diskpart+drive

Your raid configuration has probably left the drive in a state where Windows 7 Setup wont touch it as it's treated as a forgein disk.

Make sure that you have the drive as the bootable drive in your BIOS/EFI and that you have a disk mode that both the motherboard and the drive are happy with (e.g. AHCI/SATA Native or IDE Mode/IDE Compatability).

@Detection I noticed that

He said already that he disabled RAID and is trying to use it as a single drive

Get over it dude, just trying to help...

Wow, touchy much?

If you can't hack people pointing out what has already been said in a thread, probably better read them first don't you think ?

Thanks guys - I appreciate the help here. We're making some progress! Turns out that Aergan was on the right track with this. I've done a diskpart and setup can at least now see the drive! However, we're now going through a whole "windows cannot be installed to this disk, the computer's hardware may not support booting to this disk" thing. I'm just trying a "clean all" in diskpart and hoping we can move forward from there.

Unfortunately, this old motherboard is an absolute pile of $* - you cannot specify what mode the disk runs on, and from what I can google it's suggesting that AHCI isn't supported anyhow, so it's running it in IDE mode. Hopefully we're getting there now. Any thoughts on the "Windows cannot be installed to this disk" message would be much appreciated though.

Really appreciate ALL of the thoughts and suggestions so far.

Thanks guys - I appreciate the help here. We're making some progress! Turns out that Aergan was on the right track with this. I've done a diskpart and setup can at least now see the drive! However, we're now going through a whole "windows cannot be installed to this disk, the computer's hardware may not support booting to this disk" thing. I'm just trying a "clean all" in diskpart and hoping we can move forward from there.

Unfortunately, this old motherboard is an absolute pile of $* - you cannot specify what mode the disk runs on, and from what I can google it's suggesting that AHCI isn't supported anyhow, so it's running it in IDE mode. Hopefully we're getting there now. Any thoughts on the "Windows cannot be installed to this disk" message would be much appreciated though.

Really appreciate ALL of the thoughts and suggestions so far.

You might be able to install Windows to that drive anyway. The other day I was installing Windows 8 to a VHD and it gave that error, but I was able to ignore it and install Windows on it.

Did you try deleting and remaking the disk partition in the windows set up?

I certainly did :) It was at that point that I get this error message now.

You might be able to install Windows to that drive anyway. The other day I was installing Windows 8 to a VHD and it gave that error, but I was able to ignore it and install Windows on it.

Hmmm, it would appear that's an improvement in Windows 8 over 7 - this darned thing just will not let you continue :/

at setup do diskpart (SHIFT+F10)

then try.....

I've done that one before, which is what managed to get the drive recognised by Setup. Unfortunately, that's not getting around this "The hardware may not support booting from this disk" error. I've left a "clean all" running on it at the moment in the vague hope that might fix it up. I'll then try creating and flagging the partitions manually.

I think failing that, maybe I should attempt to install Ubuntu just to get SOME kind of O/S on the disk and booting, then attempt to re-format and install windows over the top of it.

Believe it or not, it's actually only a 500GB drive, which is why I'm so confused it's giving me all this trouble!

However - we finally have success :) After a thorough clean all, a large dose of patience, and a reboot later and it is now installing! Thank you everyone!

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • It had gone weeks ago. Although thinking about it I'm on the beta.
    • They thought value of their goods would forever only drop like it used to and didn't account for sudden increase in price because of all the Ai hype. Tough luck Samsung, don't try to weasel this one out. Also American customer protection laws are a**. In Europe, you need to be compensated for a functioning product of same or better characteristics (not same price point as when it was originally bought!) if it can't be repaired and when you receive a replacement product your warranty starts from scratch because you received a different item than you previously had and old warranty thus cannot apply to it anymore. If your actual item was successfully repaired, warranty gets extended for the period the item was in service. If item is repaired to a significant extent, warranty also starts over from scratch because major part of it was replaced. Americans need to fight to get this kind of consumer protections because they are constantly getting screwed over.
    • Microsoft releases new Windows 11 Media Creation Tool with the latest updates by Taras Buria Patch Tuesday updates arrive every month, bringing users new features and security updates. To make sure customers have access to the most recent images, Microsoft also releases updates to the Media Creation Tool app, its official utility for Windows 11 installation. Today, the company pushed new ISOs to Media Creation Tool, allowing you to create images with the June 2026 Patch Tuesday updates. With the latest update, the Media Creation Tool now downloads KB5094126. It is Windows 11 version 25H2, build 26200.8655, which is also available via Windows Update. Note that the app itself remains on the previous version, which you can check in Properties > Details. The only change is that it now downloads a more recent Windows 11 build, so the only way to check is to download an ISO. The June 2026 Patch Tuesday update is a special release for Windows 11, as it brings a new performance profile to make the operating system more responsive and snappier when rendering various user interface surfaces, including the Start menu, quick settings, and more. It does so by spiking processor speeds for a brief moment, resulting in higher loads for a second or two. The so-called “Low latency profile” is rolling out gradually, but you can force-enable it with the ViVeTool app. Other changes include webcam improvements, Task Manager updates, shared audio support, and more. You can download the Media Creation Tool app from the official Microsoft website using this link. Besides MCT, Microsoft lets you download Windows 11 ISO as a file directly from the official Windows 11 website. However, you will need a third-party app to write it to your USB drive. Check out this guide if you want to know how to do that.
    • Louis Rossmann suing Samsung over "990 Pro SSD warranty scam" by Sayan Sen Back in 2023, if you recall, Neowin reviewer Robbie Khan had a dispute with Samsung over his 990 Pro SSD, which was rapidly losing its health. After significant back and forth, the tech giant had finally released firmware to "stop" the issue. Interestingly, its previous flagship at the time, the 980 Pro was also facing problems leading to two consecutive sets of firmware fixes. Three years later, it looks like a similar conflict has now broken out between tech repair entrepreneur YouTuber Louis Rossmann and Samsung, as it has escalated into a threatened lawsuit after the company allegedly refused to appropriately replace a failing 990 Pro SSD that remained under warranty. According to Rossmann, a 4TB Samsung 990 Pro NVMe SSD purchased for approximately $330 less than two years ago, began experiencing major hiccups and issues, even though he claims it had been operated under ideal cooling conditions. It was installed in a RAID 1 array and cooled by a heatsink and dual high-speed fans. However the drive reportedly started dropping out of the array, exhibiting controller-level failures that eventually became not useable in any meaningful way. Rossmann said Samsung’s support process was marked by delays and confusion from the very start. After initially contacting the wrong regional support channel, he was redirected to Samsung’s memory support division where he submitted detailed diagnostics, logs, and proof of purchase. Rossmann runs a repair company and owns an ACE Lab PC-3000 machine, which is a professional-grade data recovery equipment. As such, he had been confident in his diagnostics. Samsung even seemingly acknowledged that later. Regardless, Rossmann claims that his initial support ticket was automatically closed before a full 24-hour response window had elapsed, forcing him to reopen the case and resubmit documentation. The controversy however intensified further from here after Samsung accepted the drive for warranty evaluation but later returned it with a repair report stating that the drive had passed its testing and that the SSD had been verified as functional. Rossmann strongly disputed those claims citing that his own independent testing on PC-3000 showed write speeds reducing to as low as 40–60 MB/s before the drive failed entirely. Samsung subsequently informed him that the SSD had been reset and reflashed, passing internal stress tests. However, the company also stated that replacement units were unavailable due to an industry-wide memory shortage and suggested that a refund process could be initiated if further testing confirmed the fault. Thus, to settle, the company offered a refund of $330, the amount that was initially paid by him to make the purchase. Here, Rossmann pointed out the seeming hypocrisy of the tech giant as in how no Samsung drive was apparently allocated for warranty replacements, but they were abundantly available for retail sales especially when using business accounts. As you can see, Rossmann is indeed right, there are Samsung 990 Pro 4TB SSDs on Amazon currently for $950 (shipped and sold by first-party Amazon US itself), and they are also available on Samsung's own store too, albeit for an even higher price of $1100. Thus Rossmann argues that Samsung’s inability or unwillingness to provide a replacement while the same model remains available for purchase at significantly higher market prices reflects a failure to honor its warranty obligations. He has issued a formal 60-day notice and says he intends to file suit in Texas small claims court, asserting that companies should face greater costs for denying legitimate warranty claims than for fulfilling them. You can check out the full video titled "Samsung's 990 Pro SSD warranty policy is a scam; I'm taking them to court," at the link below. Source and image: Louis Rossmann (YouTube) As an Amazon Associate we earn from qualifying purchases
  • Recent Achievements

    • Week One Done
      davidbazooked earned a badge
      Week One Done
    • One Month Later
      Jamswaz earned a badge
      One Month Later
    • Week One Done
      Jamswaz earned a badge
      Week One Done
    • Rookie
      Marzoid went up a rank
      Rookie
    • Community Regular
      coch went up a rank
      Community Regular
  • Popular Contributors

    1. 1
      +primortal
      509
    2. 2
      PsYcHoKiLLa
      184
    3. 3
      +Edouard
      158
    4. 4
      Steven P.
      83
    5. 5
      ATLien_0
      75
  • Tell a friend

    Love Neowin? Tell a friend!