Two PCs, direct connection with ICS. Unidentified network.


Recommended Posts

Do to a temporary rearanging of things in the house, I've got two PCs connected with an eithernet cable sharing internet. One of them has a wireless card to connect to the router and it is sharing the connection with the other PC.

At first, it wouldn't work. Both PCs said the local area connection was unidentified. I noticed that they were on a different subnet. After some research, I learned that the unidentifed network issue is usually due to them not having a common gateway. I manually entered the IPv4 settings to put them on the same subnet and pointed one at the other as their gateway. Still didn't fix it. I then set everthing to defaults and magically after all the reboots and everthing, it started working.

Today, I wasn't getting a good enough signal to download some files quickly enough, so I ran a temporary line from PC2 (PC without wireless card), down the hallway to the router. After, when I hooked PC2 back up to PC1, I was back to having the original problem again. Now I can't get it working again.

Both are running Win7 Pro.

PC #1

Windows IP Configuration

Host Name . . . . . . . . . . . . : Upstairs
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Mixed
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No

Ethernet adapter Local Area Connection:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller
Physical Address. . . . . . . . . : 00-13-8F-89-79-2B
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::c16d:9d2e:b442:e59e%11(Preferred)
Autoconfiguration IPv4 Address. . : 169.254.229.158(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.0.0
Default Gateway . . . . . . . . . :
DHCPv6 IAID . . . . . . . . . . . : 234886031
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-B2-88-D2-00-13-8F-89-79-2B

DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1
fec0:0:0:ffff::2%1
fec0:0:0:ffff::3%1
NetBIOS over Tcpip. . . . . . . . : Enabled

Tunnel adapter isatap.{5CE07A93-112E-4335-BBCB-ADC9A493A2B4}:

Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft ISATAP Adapter
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes

Tunnel adapter Teredo Tunneling Pseudo-Interface:

Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
[/CODE]

PC #2 - the Linksys LNE100TX card is unused at the moment. Only using the interface on the mobo.

[CODE]Windows IP Configuration

Host Name . . . . . . . . . . . . : Downstairs
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No

Ethernet adapter Local Area Connection 2:

Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Linksys LNE100TX(v5) Fast Ethernet Adapter
Physical Address. . . . . . . . . : 00-14-BF-5C-73-54
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes

Ethernet adapter Network Bridge:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : MAC Bridge Miniport
Physical Address. . . . . . . . . : 02-0F-EA-47-1B-CA
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::c04c:2715:c4e1:92c3%18(Preferred)
IPv4 Address. . . . . . . . . . . : 192.168.2.100(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Lease Obtained. . . . . . . . . . : Wednesday, August 15, 2012 6:27:59 AM
Lease Expires . . . . . . . . . . : Saturday, September 21, 2148 5:46:35 PM
Default Gateway . . . . . . . . . : 192.168.2.1
DHCP Server . . . . . . . . . . . : 192.168.2.1
DHCPv6 IAID . . . . . . . . . . . : 318902250
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-16-29-2B-DB-00-0F-EA-47-1B-CA

DNS Servers . . . . . . . . . . . : 192.168.2.1
NetBIOS over Tcpip. . . . . . . . : Enabled

Tunnel adapter isatap.{4C5EA07A-652B-48B9-97D5-7B6019F18CEC}:

Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft ISATAP Adapter
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes

Tunnel adapter Local Area Connection* 12:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:3c32:2710:e7f0:6bd8(Preferred)
Link-local IPv6 Address . . . . . : fe80::3c32:2710:e7f0:6bd8%20(Preferred)
Default Gateway . . . . . . . . . : ::
NetBIOS over Tcpip. . . . . . . . : Disabled

Tunnel adapter isatap.{611A51AC-4BA0-4DF5-85E1-A0D4C314AD19}:

Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft ISATAP Adapter #3
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes

Tunnel adapter Local Area Connection* 13:

Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft ISATAP Adapter #4
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
[/CODE]

Right. PC #1 (named downstairs) has it's wired NIC and wireless NIC bridged. I've set the router to give it the static IP 192.168.2.100. It's always been that way, and I haven't messed with the router settings since way before this.

When things were miraculaouly working yesterday, PC #1 gave PC #2 the IP 192.168.2.114. With all NICs set to default settings to obtain IPs automatically.

"PC #1 gave PC #2 the IP 192.168.2.114. With all NICs set to default settings to obtain IPs automatically."

NO -- if you were bridged, then the Router your pc#1 is connected to would give the pc#2 its address and other dhcp info like mask and gateway and dns.

There is HUGE difference between ICS and Bridged interfaces.

So you have router --- wireless ---- PC#1 --- wired --- PC#2

dhcp scope on your router is

192.168.1.100 to 150

mask 255.255.255.0 or /24

gateway (itself) 192.168.1.1

dns (itself again or say opendns, googledns - whatever lets call it itself) 192.168.1.1

router is say 192.168.1.1, pc1 gets 192.168.1.100, pc2 would be 192.168.1.101

In a bridge (pc1) He sees packets on his interface 1, he sends it out interface 2, he sees packets on interface 2 he sends it out 1 - that is what a bridge does.

In ICS, your PC1 would be like a ROUTER, and doing NAT on the network he created on his 2nd interface. They are 2 different methods to accomplish pretty much the same thing. with ICS you would have something like this

router (192.168.2.1) ---- (192.168.2.100)PC1(192.168.1.1) ----(192.168.1.100)PC2

In that sort of setup PC1 would be the gateway for PC2, and the dhcp server and the DNS, just like your router is for PC1 -- where you can run into problems with ICS, is if you have duplicated networks on both interfaces of PC1. Depending on your OS version you would have to look up what the default IP of the ICS interface would be. In XP for example the ICS interface would have an IP address of 192.168.0.1. Not sure what it is in vista or w7 to be honest - might be the same.

I really don't play with ICS very often because a router cost like $20, there really is NO sort of configuration where ICS would be the desired setup.

If you need to extend a connection for example to another machine, like your setup where you have a wired connection to pc2 from pc1 and you want to share pc1 wireless interfaces network connection (internet) then sure bridging works just fine as a temp sort of solution until you can correctly setup your network where pc2 has its own actual connection to the network.

Delete the bridge and setup a ad-hoc between the two PC's to test the wireless you will need to setup the IP's manually.

Ok so the bridge is connected by wireless to your router with the bridge wired to the other PC...

Damaged cable maybe?

Like I said, this is a temporary situation. Normally everything is hooked up to the router. And I assumed since the machine was sharing it's connection with another, it was called ICS. I get the difference now. Thanks.

I still don't get why PC#1 isn't getting an address from the router.

This thread is good as any other to have a quick discussion on why you might pick ICS over Bridging or vice vesa, etc.

When you would want bridging:

Lets say you wanted to be able to do port forwarding to your devices that don't have their own connection to the network and are going to be connected via the bridging PC. What if you wanted to be able to see broadcast traffic on other devices directly connected to the routers network via wired or wireless. A bridge would put the clients all on the same network(broadcast domain) So your router could forward ports to them, your devices behind the bridge would be able to use UPnP to your gateway router, etc.

When would you want to use ICS over bridging.

Let say you had lots of devices that don't have a method to connect to the router - say no wireless interfaces. Or maybe your wireless device in the PC you were going to use to bridge does not like bridging and just doesn't work. If you wanted to isolate broadcast traffic from these 2 network, maybe you are going to have lots of traffic between clients, and don't want that traffic being sent onto the wireless network because it would eat up the wireless bandwidth. But your ok with just these clients internet traffic. And you only have a HUB to connect these other devices not a switch

For example in the above setup with PC1 bridging to his wireless network to a PC2, what if you had 5 other PCs that you wanted to have internet connectivity behind this PC1. And you stream say video or move large files between PC3 and PC5. You would not want PC1 sending all those packets onto the wireless network. And you were going to connect these other PCs to PC1 with a HUB. So PC1 bridge interface would see all this traffic and send it out his wireless interface.

Maybe you don't want broadcast traffic from these PCs behind PC1 to go out to the wireless network, maybe you don't want these PCs to be able to use UPnP on the router. Maybe you don't want PCs connect to the routers network to be able to access the other PCs behind PC1

In those types of cases then turning PC1 into a NAT router would make sense. You would have 2 different networks, you would have 2 different broadcast domains. There would be a NAT between network 1 and network 2, so that PCs connected to the router could not access PCs behind the NAT.

There lots of different reasons you might want to use ICS vs Bridging in a temp type of configuration to get something to work while you work out the final/correct setup.

But normally if its only 1 or 2 machines you need to connect to your routers network - and there is a PC that is connected then sure quick bridge of that PCs interface would be the fastest easiest method of getting these other PCs on the network and internet.

As to why PC1 isnt getting an IP?? Did you try doing a release and renew on it?

if you showing lights on the interface on your PC2 (bridge PC) - you could try setting static on PC1

give it say 192.168.2.101, 255.255.255.0, gateway 192.168.2.1, dns 192.168.2.1

Can you ping 192.168.2.100? Can you ping 192.168.2.1 ?? If not, what do you show in PC1 arp table after you try and ping

arp -a in cmd prompt on PC1

Maybe your wireless card just doesn't like bridging? Maybe you have a firewall on PC1 blocking DHCP?? There are **** load of reasons what you might be doing wrong.

edit: BTW to make your ipconfig /all easier to read - your clearly not using IPv6, so why don't just fully disable it so we don't see all that teredo/tunnel ****

from elevated cmd prompt

reg add hklm\system\currentcontrolset\services\tcpip6\parameters /v DisabledComponents /t REG_DWORD /d 255

Above will fully disable IPv6, if you want to put it back to the way it is now - just delete the regkey with

reg delete hklm\system\currentcontrolset\services\tcpip6\parameters\ /v DisabledComponents /f

Then your output will look much cleaner. Here is my Box - even using IPv6 and its a lot cleaner looking ;)

post-14624-0-38049800-1345057738.jpg

I can ping both 192.168.2.1 and 192.168.2.100. Here is what I get when I run arp -a on PC1.


Interface: 192.168.2.105 --- 0xb
Internet Address Physical Address Type
192.168.2.1 bc-ae-c5-e7-d0-ce dynamic
192.168.2.100 00-18-39-0e-ec-a7 dynamic
192.168.2.255 ff-ff-ff-ff-ff-ff static
224.0.0.22 01-00-5e-00-00-16 static
224.0.0.252 01-00-5e-00-00-fc static
239.255.255.250 01-00-5e-7f-ff-fa static
255.255.255.255 ff-ff-ff-ff-ff-ff static
[/CODE]

Firewalls haven't changed. It was working for a few days. All I did was plug the cable into the router temporarily and then it wasn't working when I switched it back.

Changed PC1 to static

192.168.2.105

255.255.255.0

192.168.2.1 for gateway & dns

Could no longer ping 192.168.2.1 or 192.168.2.100. Destination host unreachable.

Arp table

[CODE]
Interface: 192.168.2.105 --- 0xb
Internet Address Physical Address Type
192.168.2.255 ff-ff-ff-ff-ff-ff static
224.0.0.22 01-00-5e-00-00-16 static
224.0.0.252 01-00-5e-00-00-fc static
[/CODE]

Interface: 192.168.2.105 --- 0xb

Internet Address Physical Address Type

192.168.2.255 ff-ff-ff-ff-ff-ff static

224.0.0.22 01-00-5e-00-00-16 static

224.0.0.252 01-00-5e-00-00-fc static

Well its never ever in a million years going to work if you don't have mac address of IPs in your table.

Lets be clear here on PC#

you say PC1 is Upstairs

and PC2 (bridge box) is Downstairs.

So its going to be a given that your bridge box PC2 can ping itself and gateway (router 192.168.2.1)

But your PC1 (non bridged box) Is not showing mac for router or even the mac for the interface the bridgebox its directly connected too.

So you got a bad cable? Its not doing autocross, or its not crossover - but until you can see the mac your never going to get to the router.

You said you were bridging the built in interface on the MB? I show 2.100 Mac

00-18-39 as Cisco-Linksys, and

bc-ae-c5 as ASUSTek COMPUTER INC <--- This is your router.

I dont think I have ever seen a cisco-linksys built in nic before? You sure you have the correct interfaces bridged?

Can you output your bridge setup using netsh

from cmd line do

netsh

you should then see

netsh>

then type bridge then show adapter and we should see your bridge configuration.

I can setup one real quick to show you the commands I am talking about in an example -- give me a few minutes

edit: Break your bridge, then output ipconfig /all then recreate your bridge and show the output of your netsh bridge show adapter command -- I will post example her in a minute or 2, my vm is booting.

edit2: ok here is before bridge - forget the ips for now


Ethernet adapter Local Area Connection 2:

   Connection-specific DNS Suffix  . : local.lan
   Description . . . . . . . . . . . : vmxnet3 Ethernet Adapter #2
   Physical Address. . . . . . . . . : 00-0C-29-53-2C-03
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
   IPv4 Address. . . . . . . . . . . : 192.168.1.210(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Lease Obtained. . . . . . . . . . : Wednesday, August 15, 2012 3:48:34 PM
   Lease Expires . . . . . . . . . . : Thursday, August 16, 2012 3:48:33 PM
   Default Gateway . . . . . . . . . : 192.168.1.253
   DHCP Server . . . . . . . . . . . : 192.168.1.253
   DNS Servers . . . . . . . . . . . : 192.168.1.253
   NetBIOS over Tcpip. . . . . . . . : Enabled

Ethernet adapter Local Area Connection:

   Connection-specific DNS Suffix  . :
   Description . . . . . . . . . . . : Intel(R) PRO/1000 MT Network Connection
   Physical Address. . . . . . . . . : 00-0C-29-53-2C-0D
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
   IPv4 Address. . . . . . . . . . . : 192.168.1.41(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Default Gateway . . . . . . . . . : 192.168.1.253
   DNS Servers . . . . . . . . . . . : 192.168.1.253
   NetBIOS over Tcpip. . . . . . . . : Enabled

now in bridge

C:\Windows\system32&gt;ipconfig /all

Windows IP Configuration

   Host Name . . . . . . . . . . . . : W7X64-VM
   Primary Dns Suffix  . . . . . . . : local.lan
   Node Type . . . . . . . . . . . . : Broadcast
   IP Routing Enabled. . . . . . . . : No
   WINS Proxy Enabled. . . . . . . . : No
   DNS Suffix Search List. . . . . . : local.lan

Ethernet adapter Network Bridge:

   Connection-specific DNS Suffix  . :
   Description . . . . . . . . . . . : MAC Bridge Miniport
   Physical Address. . . . . . . . . : 02-0C-29-53-2C-03
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
   Autoconfiguration IPv4 Address. . : 169.254.212.136(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.0.0
   Default Gateway . . . . . . . . . :
   NetBIOS over Tcpip. . . . . . . . : Enabled

C:\Windows\system32&gt;netsh
netsh&gt;bridge
netsh bridge&gt;show adapter

----------------------------------------------------------------------
ID AdapterFriendlyName		 ForceCompatibilityMode
----------------------------------------------------------------------
  1 Local Area Connection 2	 unknown
  2 Local Area Connection	   unknown
----------------------------------------------------------------------

edit: as I mentioned before some wireless cards don't like bridge mode, they need to support Promiscuous Mode

http://support.microsoft.com/kb/302348/en-us

Bridge May Not Work With a Non-Promiscuous Mode Network Adapter

You said you were bridging the built in interface on the MB? I show 2.100 Mac

00-18-39 as Cisco-Linksys, and

bc-ae-c5 as ASUSTek COMPUTER INC <--- This is your router.

I dont think I have ever seen a cisco-linksys built in nic before? You sure you have the correct interfaces bridged?

00-18-39 is the wireless on PC2, which is a Linksys. That's what I want, right? The PC1 connected to the LAN on PC2, and the LAN and wireless on PC2 bridged so that PC1 gets internet.

Broke bridge. PC2 config:


Windows IP Configuration
Host Name . . . . . . . . . . . . : Downstairs
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
Ethernet adapter Local Area Connection 2:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Linksys LNE100TX(v5) Fast Ethernet Adapter
Physical Address. . . . . . . . . : 00-14-BF-5C-73-54
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Ethernet adapter Network Bridge:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : MAC Bridge Miniport
Physical Address. . . . . . . . . : 02-0F-EA-47-1B-CA
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Wireless LAN adapter Wireless Network Connection:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Broadcom 802.11n Network Adapter
Physical Address. . . . . . . . . : 00-18-39-0E-EC-A7
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IPv4 Address. . . . . . . . . . . : 192.168.2.114(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Lease Obtained. . . . . . . . . . : Wednesday, August 15, 2012 7:41:42 PM
Lease Expires . . . . . . . . . . : Sunday, September 22, 2148 2:15:23 AM
Default Gateway . . . . . . . . . : 192.168.2.1
DHCP Server . . . . . . . . . . . : 192.168.2.1
DNS Servers . . . . . . . . . . . : 192.168.2.1
NetBIOS over Tcpip. . . . . . . . : Enabled
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : VIA Rhine II Fast Ethernet Adapter
Physical Address. . . . . . . . . : 00-0F-EA-47-1B-CA
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
IPv4 Address. . . . . . . . . . . : 169.254.229.101(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 169.254.229.100
NetBIOS over Tcpip. . . . . . . . : Enabled
[/CODE]

Recreated bridge.

[CODE]
netsh>bridge
netsh bridge>show adapter
----------------------------------------------------------------------
ID AdapterFriendlyName ForceCompatibilityMode
----------------------------------------------------------------------
1 Wireless Network Connection unknown
2 Local Area Connection unknown
----------------------------------------------------------------------
[/CODE]

Then how do you still have a Bridge listed in your output? Did you create multiple bridges? Delete all bridges shown in Control Panel\Network and Internet\Network Connections

Then recreate it, and I would put your wireless adapter

netsh bridge set adapter X forcecompatmode=enable

http://support.microsoft.com/kb/302348/en-us

edit: Break your bridge, then output ipconfig /all then recreate your bridge and show the output of your netsh bridge show adapter command -- I will post example her in a minute or 2, my vm is booting.

That's what I did. The bridge is showing enabled because I enabled it before doing the netsh bridge show adapter.

Odd that a bridge would stay with no members - easy way to break a bridge is to just delete it, that would of been my method. But sure ok, my bad.

So set the forcecompatmode=enable on your wireless interface and see if that helps. Again some wireless just do not like to bridge, they have to support promiscuous mode, etc.

its hard for me to do remote, but I can recreate what your trying to do when I get back to the house. But tonight is BEER night, so not sure when that will be ;)

If you can not get the bridge mode to work, then go the ICS route - that should work even if your wireless does not support bridge mode.

Deleted bridge


Wireless LAN adapter Wireless Network Connection:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Broadcom 802.11n Network Adapter
Physical Address. . . . . . . . . : 00-18-39-0E-EC-A7
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IPv4 Address. . . . . . . . . . . : 192.168.2.100(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Lease Obtained. . . . . . . . . . : Thursday, August 16, 2012 10:16:05 AM
Lease Expires . . . . . . . . . . : Sunday, September 22, 2148 4:50:40 PM
Default Gateway . . . . . . . . . : 192.168.2.1
DHCP Server . . . . . . . . . . . : 192.168.2.1
DNS Servers . . . . . . . . . . . : 192.168.2.1
NetBIOS over Tcpip. . . . . . . . : Enabled
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : VIA Rhine II Fast Ethernet Adapter
Physical Address. . . . . . . . . : 00-0F-EA-47-1B-CA
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
IPv4 Address. . . . . . . . . . . : 169.254.229.101(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 169.254.229.100
NetBIOS over Tcpip. . . . . . . . : Enabled
[/CODE]

Recreated bridge

[CODE]
----------------------------------------------------------------------
ID AdapterFriendlyName ForceCompatibilityMode
----------------------------------------------------------------------
1 Wireless Network Connection unknown
2 Local Area Connection unknown
----------------------------------------------------------------------
[/CODE]

I don't see how my wireless adapter would have a problem with bridge when it worked flawlessly for the few days until I unplugged the cable.

Also did forcecompatmode=enable, but nothing has changed.

I don't know either, for all we know you were using ICS before?? I can not troubleshoot what I can not see, the heading of this thread is ICS, but your talking bridging. So to be frank - I have no idea what you were doing before

But what I can tell you is the wireless card does need to support promiscuous mode - and from your bridge output, its not known if its in that mode or not? So you could try setting it.

If that does not work - then use ICS mode. Unless you have a NEED to port forward traffic from your router to the box behind your PC connected to your netework the box behind the bridge or the ICS would have little difference in accessing normal stuff on the internet.

But it was never ever going to work from what you posted before with the box behind not showing MAC for the gateway IP.

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • As I've been usually saying lately - we all can thank "AI" for this.
    • Friday Windows 11 preview builds are here. Insiders in the Experimental (formerly Dev) and Beta Channel can download builds 26300.8697 and 26220.8690. My Windows11 device on the Preview Channel just got 26220.8728. My guess is this build is a nightly update from 26220.8690.
    • Traffic has a surprisingly unexpected impact on your surroundings by Sayan Sen Image by Radik 2707 via Pexels A collaborative study by researchers from several Israeli institutions found that everyday pollution from traffic and industrial activity measurably changed the atmospheric electric field over the Tel Aviv metropolitan area, providing new evidence of how human activity can influence the lower atmosphere. The research was led by Dr. Roy Yaniv of the Hebrew University of Jerusalem and the Gertner Institute at Sheba Medical Center, Dr. Assaf Hochman of the Fredy & Nadine Herrmann Institute of Earth Sciences at the Hebrew University, and Prof. Yoav Yair of Reichman University. The study also involved Itay Froomer, a student from Hadera High School and the Israeli Museum of Medicine and Science (Technoda), who carried out the work as part of the Ministry of Education's 5-unit physics research track. The researchers focused on the atmospheric electric field under fair-weather conditions. Even in the absence of storms, a weak electric field naturally exists between Earth's surface and the atmosphere. One of the main ways scientists measure this field is through the Potential Gradient (PG), which is the inverse of the vertical component of the electric field. PG is a key part of the global electric circuit, a planet-wide system of electrical currents maintained by thunderstorms and electrified clouds around the world. Scientists have long known that the atmospheric electric field can be influenced by factors ranging from large-scale atmospheric processes to local weather conditions such as dust, fog and clouds. Human-made pollution is also known to play a role, but understanding exactly how urban emissions affect the electric field close to the ground has remained an area of ongoing research. To investigate this relationship, the team analyzed measurements from a newly installed electric field mill, an instrument used to continuously monitor the strength of the atmospheric electric field. The instrument was installed at the Center for Technological Education (Roter House) in Holon and became operational in August 2024. It was funded by Israel's Ministry of Education and the Holon municipality. The electric field mill forms part of a broader monitoring network that includes nearby meteorological stations and air-quality monitoring sites. This allowed researchers to compare electric field measurements with detailed weather data and pollution records to better understand what was driving changes in the Potential Gradient. The study focused on two major urban pollutants: fine particulate matter (PM2.5) and nitrogen oxides (NOx), both commonly produced by vehicle traffic and industrial activity. PM2.5 refers to microscopic airborne particles small enough to remain suspended in the atmosphere for extended periods, while NOx is a group of gases released during fuel combustion. Researchers examined daily, weekly and seasonal patterns in the atmospheric electric field and compared them with changes in pollutant concentrations. Their analysis revealed a clear relationship between NOx levels and changes in the Potential Gradient, particularly during morning and evening rush hours when traffic emissions were at their highest. “What we observe is a direct physical link between emission peaks and electrical variability,” explained Dr. Roy Yaniv. “NOx reduces atmospheric conductivity very quickly, so the electric field responds almost instantaneously during traffic rush hours.” Atmospheric conductivity describes how easily electrical charges move through the air. According to the researchers, nitrogen oxides rapidly alter this conductivity, causing a near-immediate response in the electric field. PM2.5, however, was associated with a delayed response. The researchers attributed this difference to the particles' longer atmospheric residence time, meaning they remain in the atmosphere for longer periods, as well as their different microphysical interactions with surrounding air and atmospheric components. The study also identified a pronounced "weekend effect." In Israel, traffic volumes and some industrial activity decline significantly on Fridays and Saturdays. During these periods, concentrations of both NOx and PM2.5 dropped, and corresponding changes were observed in the atmospheric electric field. “The weekend signal demonstrates just how sensitive the electric field is to changes in human activity,” the researchers noted. “When emissions decline, the electrical environment adjusts at once, providing a high-resolution indicator of urban atmospheric conditions.” The findings showed that pollution levels can influence not only the chemical composition of the atmosphere but also its electrical properties. Researchers said the results strengthened the case for using atmospheric electricity as an additional tool for environmental monitoring, particularly in densely populated urban areas where anthropogenic, or human-caused, influences are most pronounced. The study also pointed to potential public health applications. By combining air-quality measurements with observations of atmospheric electricity, researchers said they could gain a more complete picture of how urban atmospheric conditions change over time. “Integrating air-quality data with electric-field measurements gives us a clearer picture of how the lower atmosphere evolves moment by moment,” the researchers added. “It’s a framework that can support both scientific insight and practical environmental decision-making.” Beyond the scientific findings, the project highlighted a collaboration between universities, public institutions and secondary education. Researchers said the work demonstrated how students could take part in real-world environmental research while contributing to studies of air quality, atmospheric processes and their potential effects on society. Source: Hebrew University, ScienceDirect This article was generated with some help from AI and reviewed by an editor. Under Section 107 of the Copyright Act 1976, this material is used for the purpose of news reporting. Fair use is a use permitted by copyright statute that might otherwise be infringing
    • We aren't even at the all-star game and Microsoft is talking about an update that will most likely be released during the World Series if not after. A lot can happen in the world between now and the 2026 World Series, including the 2026 FIFA Cup. Tell me about it again after the FIFA Cup is concluded. That should allow plenty of time to prepare for it.
    • Great, tell me when I have a "Bad Pool Caller" elsewhere not in Windoze.
  • Recent Achievements

    • Week One Done
      AMV earned a badge
      Week One Done
    • One Month Later
      AMV earned a badge
      One Month Later
    • Collaborator
      ryansurfer98 went up a rank
      Collaborator
    • One Month Later
      Eurosoft10 earned a badge
      One Month Later
    • Week One Done
      Eurosoft10 earned a badge
      Week One Done
  • Popular Contributors

    1. 1
      +primortal
      542
    2. 2
      +Edouard
      186
    3. 3
      Michael Scrip
      77
    4. 4
      PsYcHoKiLLa
      77
    5. 5
      Steven P.
      71
  • Tell a friend

    Love Neowin? Tell a friend!