Delay in Remote Desktop Connection. What are possible solutions?


Recommended Posts

I am experiencing delays and reconnecting issues when connecting to RDP. Both wired and wireless.

I have purchased a new router - Linksys EA3500 - and still these issues occur.

Ping tests stated around 18ms for my connection.

My internet speeds/subscription are 120 MB down, 10 MB up. I have tested with different "Experience / Performance" settings within RDP, from low-speed broadband to high-speed broadband; all without success.

I have KIS2013 installed with default settings on both computers (wired and wireless).

What can be the issues for these delays/secs of 'hickups' during the RDP-connection?

RDP connections to where? Some box on the internet, or between boxes on your own network - wired to wireless, wireless to wireless, wired to wired?

Also what do you consider delay, 2 seconds, 5 seconds, 10, 20, 3 minutes?

RDP to some box (server) on the internet - our server 80 km away.

The server is wired to its backbone/Internet, I make a RDP-connection via my computer (wired) or notebook (wireless) from home (or elsewhere) - I use its name/alias and not the IP.

The delay is a couple of seconds (mostly 2-5 sec); screen 'freezes', reconnecting popups appears, connection is back again and I can start working again...

And this once every 2-5 minutes.

EDIT:

adjusted delay time to real circumstances

well there could always be a slight delay in resolving to its FQDN, I think that is what you meant by name/alias because those are not resolvable on the internet but a fully qualified domain name is ;) something.something.tld

so you its not really a delay in connection, but a loss of connection and reconnect

"this once every 2-5 minutes."

Are you connecting via a VPN to this server, or just the normal RDP 3389 just over the internet? Is there any firewall on the other end limiting connections to this port to only where your coming from?

You put 3389 open on the public internet and its going to get hit quite often with people attempting to log in.

If your saying it happens every few minutes I would look at logs on server side for any hints, and also would sniff the traffic from your connection. This will show you if your getting a lot of retransmission on lost packets, etc.

lagging could be upstream not fast enough to handle request, could be dns not fast enough to handle name resolution...you mention your upstream, is your upstream the upstream at home or your upstream at the office. The upstream at the office needs to be ~1Mb/s for optimal response...your down stream at home needs to be at least that. Also the dns plays quite a bit into speed, try connecting to the ip to negate dns being an issue. if it is fast connecting to the outside ip, then the issue is dns related.

it's kinda strange... when I use my cell phone with tethering (wayyy slower connection, everything is ok) on the same notebook, I have a good connection and no delay/lag.

It seems that either my modem or router is the "bad kid in town".

I just got a new router today - default settings - so that should not be the issue.

I might just check a direct cable connection from my modem to my computer (thus cancelling out the router) and see what happens...

I'll come back to this latter thing.

@ +Chris13NT, how can I prevent this? Or is this ISP-related?

Just tested it "quick and dirty" and the delay/lag is not present when connecting directly to the modem.

When I put my router in between the lag is there yet again.

There is a power/surge adapter to prevent over-voltage, but this hasn't been an issue ever since.

Might it be cable related? And that one of the UTP-cables has been damaged/is broken?

Replacing might help, but that I need to get myself some new cables....

By the way, the current cable-setup is:

ISP-entrance in my home - cable to modem, provided bij ISP - modem - cable to surge-adapter - cable to router, from there the standard 4 GBit ports of this EA3500 to computer and other periphicals + router wireless to notebook and other periphicals.

What is your dns configuration when connection directly to the modem?

start, run, cmd

ipconfig/all

What is your dns configuration when connected to the router?

start, run, cmp

ipconfig/all

change the dns on your adapter to the dns that you are getting when you are on the modem. does the same problem exist?

dns could be the problem on initial delay, or just failure to resolve - but once the connection is established and having freezes every few minutes does not seem like a dns related problem to me.

What kind of router is it? Some routers have trouble with connections over 50mbit, I had a Linksys E3000 and it couldn't cope with my 85mbit FiOS line, it would crap out every time I pegged the download.

It could be cable related but I doubt it.

I have a brand new Linksys EA3500. It should get "Transfer rates up to 300 + 450 Mbps".

The DNS I get when connect to the router is 1 IP: 192.168.1.1

When directly connected to the modem DNS server is 2 IP's: 213.48. .... and 62.179. ...

yeah those are from your ISP when connected to modem, and when connected to router your using it as your dns forwarder. This is a common setup, your router would then forward dns to those handed to your router via your ISP 213.48 and 62.179

But again if your having the issues once your connected, it seems highly unlikely that it would be dns related.

  On 26/09/2012 at 16:23, BudMan said:

yeah those are from your ISP when connected to modem, and when connected to router your using it as your dns forwarder. This is a common setup, your router would then forward dns to those handed to your router via your ISP 213.48 and 62.179

But again if your having the issues once your connected, it seems highly unlikely that it would be dns related.

Thx. So what can it be?

unlikely sure, test it, verify it, make sure. be sure, not be somewhat sure....perhaps the router is being retarded when forwarding, it is a link in the chain....remove the link.

I thought it was initial connection....if it is not initial connection, then it is not dns related. something is happening with the traffic when it goes from router to modem.

Can you to a trace route to the IP of the RDC server? This might give a clue if you have a hop with unusually high ping.

do tracert <ip (or dns name)> in cmd

The fact that the lag only happens when the router is in the link is making me almost positive it's the router botching things.

  On 26/09/2012 at 16:29, Chris123NT said:

Can you to a trace route to the IP of the RDC server? This might give a clue if you have a hop with unusually high ping.

do tracert <ip (or dns name)> in cmd

In which setup and from where?

From my computer, connected via router, to the RDC server?

Or from the RDC server to my computer? (and also here via router or directly connected to modem?)

  On 26/09/2012 at 17:01, hjf288 said:

Off topic but in reply to Chris, my e2000 handles my 120mbit line with ease and it has a slower CPU than your e3000..

So something is up there..

It could have just been going bad, or it could have been DD-WRT's fault.

  On 26/09/2012 at 16:29, Chris123NT said:

Can you to a trace route to the IP of the RDC server? This might give a clue if you have a hop with unusually high ping.

do tracert <ip (or dns name)> in cmd

The fact that the lag only happens when the router is in the link is making me almost positive it's the router botching things.

What kind of info do you need from this trace?

From which hop# there is a time out? or else?

There has been some less delays (but still annoying) with the new FW... although I had to wrestle myself through the Cisco Cloud Connect.

Still some delays.

Question remains....

EDIT:

I guess I was over-enthusiastic... delays still remain as strong as before :(

This topic is now closed to further replies.
  • Posts

    • I was going to say that search engines and such, have been scraping everyone's copyright, IP and data, since the beginning of the internet.
    • Microsoft is officially making the Xbox app on PC a universal launcher by Pulasthi Ariyasinghe It was earlier this year that an image mockup from Microsoft showed the Xbox app on PC with an interesting change: including support for other PC stores on the app, teasing that it may be becoming a universal launcher like GOG Galaxy or Playnite. Considering the company's new handheld initiative that will house a brand-new gaming-focused version of Windows, it was clear that this feature was on the way. And now, Xbox Insiders have access. Announced today as the 'aggregated gaming library' feature, it's poised to land this holiday on the ROG Xbox Ally and ROG Xbox Ally X to easily manage all their installed games from a single place. But before that, Xbox Insiders on PC can have a crack at it to see how it functions and provide feedback to Microsoft. In its current state, Microsoft says that the feature now supports Xbox, Game Pass, Battle.net, and "other leading PC storefronts," all handled via the Xbox PC app. The company did not detail what these other storefronts are, but Steam, Epic Games Store, Ubisoft Connect, and EA Play apps seem likely candidates. "Whether you’re on a Windows PC or a handheld device, your Xbox library, hundreds of Game Pass titles, and all your installed games from leading PC storefronts will now be at your fingertips," said the company. When a game from a supported store is installed on a PC, Insiders should now see it appear on the Xbox app in the My Library and Most Recent sections for easy access. "And this is just the beginning," adds Microsoft. "We’ll continue rolling out support for additional PC storefronts over time." Insiders can also disable this functionality and hide games from specific stores if needed from the Settings > Library & Extensions menu. Anyone interested in testing out the new 'aggregated gaming library' update can use the Xbox Insider app on PC to enroll in the ongoing Insider Previews.
    • Get this powerful mini PC with Core Ultra 9, 32GB RAM, and 1TB SSD for just $799 by Taras Buria The ASUS NUC 14 Pro+ is a powerful mini PC with capable hardware, and right now, you can get it on Amazon with a big discount. At just $799, this computer offers a Core Ultra 9 processor, 32GB of memory, and a 1TB SSD. The NUC 14 Pro+ features a low-profile aluminum chassis, which can be opened without removing rubber feet or undoing any screws. Its toolless design lets you access the storage without a screwdriver. The computer also has a rich set of ports. On the front side, you will find two USB 3.2 Gen 2 Type-C, one USB 3.2 Gen 2x2 Type-C, and a power button. Unlike the Mac mini, which has a frustrating power button placement, the power button in the NUC 14 Pro+ is located where it should be. The back of the NUC 14 Pro+ has a DC-in port, two Thunderbolt 4 ports, one 2.5G Ethernet port, one USB 3.2 Gen2 Type-A, one USB 2.0 Type-A, two HDMI 2.1, and a Kensington lock. Finally, there is a VESA mount, which lets you place the device on the back of your monitor for a cleaner desk. The computer is powered by Intel's 14th-gen Core Ultra 9 185H processor, 32GB of DDR5 memory, and a 1TB PCIe Gen4 NVMe SSD. Windows 11 Home is preinstalled, so you do not need to bring your own drive, memory, or Windows 11 license. ASUS NUC 14 Pro+ Core Ultra 9 185H, 32GB RAM, 1TB SSD - $799.99 | 27% off on Amazon US This Amazon deal is US-specific and not available in other regions unless specified. If you don't like it or want to look at more options, check out the Amazon US deals page here. Get Prime (SNAP), Prime Video, Audible Plus or Kindle / Music Unlimited. Free for 30 days. As an Amazon Associate, we earn from qualifying purchases.
    • This guy is just salty that Waymo is about to get buried by a company with cars that cost significantly less, charge significantly lower fares, and will soon dramatically outnumber their fleet. Waymo made the mistake of not reducing their vehicle cost quick enough and not overcoming their route limitations. Unless they start allowing their cars to use the freeways and have significantly wider geofencing, they're going to soon join the list of discontinued Google products. If Tesla wasn't the one to make them irrelevant, somebody else soon was. There's a long list of companies designing robotaxis right now.
    • LOL. Hard to believe people still fall for this. If you are having some sort of issue, I would work on fixing that instead turning off these settings.
  • Recent Achievements

    • Week One Done
      fredss earned a badge
      Week One Done
    • Dedicated
      fabioc earned a badge
      Dedicated
    • One Month Later
      GoForma earned a badge
      One Month Later
    • Week One Done
      GoForma earned a badge
      Week One Done
    • Week One Done
      ravenmanNE earned a badge
      Week One Done
  • Popular Contributors

    1. 1
      +primortal
      649
    2. 2
      Michael Scrip
      226
    3. 3
      ATLien_0
      219
    4. 4
      +FloatingFatMan
      146
    5. 5
      Xenon
      137
  • Tell a friend

    Love Neowin? Tell a friend!