New build won't power on - Is it the PSU?

By teknix360
in Hardware Hangout

 Share

Recommended Posts

Enthusiast

teknix360

Posted
Posted

I am building a new system today and got my core components connected. I went to do the test boot, but it won't power on. The PSU fan doesn't even spin, there is no noise, so I don't think it is drawing power. Is there a way to check?

My parts:

  • CPU: Intel Core i3-3225
  • Motherboard: ASRock H77M Micro ATX LGA1155
  • Memory: Corsair Vengeance 8GB (2 x 4GB) DDR3-1600
  • Power Supply: Corsair Builder 500W 80 PLUS Bronze Certified ATX12V

I'm just an enthusiast, not an expert so forgive my non-technical terms here. This is what I have done:

  • Installed CPU
  • Installed CPU Fan, pushed pins down and connected CPU Fan plug to mobo
  • Plugged in the big long ATX plug and the CPU plug (it's got 6 pins) from PSU to mobo
  • Installed the 2 sticks of RAM

Then I connected the PSU power plug from the PSU to the wall and flipped the switch. Nothing. I re-check to make sure everything was seated properly, and it is as far as I can tell. I tried a different power plug and a different outlet, but still nothing.

I don't have another PSU to test with. :/

I read something about CMOS jumpers, but I don't know exactly what that does and if it would help.

This is only my second build. On my last build, everything worked fine, so I'm not sure what DOA parts are like. I'm thinking my PSU is a dud, but not sure. :cry:

What else can I try?

Mentor

Mannlich

Posted
Posted

Shouldn't the CPU connector be either 4 pin or 8 pin - not heard of a 6 pin before? You didn't plug in a PCIe power connector to it did you?

This. I've never seen a 6-pin CPU connector. PCIe connectors have 6 pins.

Mentor

Guth

Posted
Posted

Did you connect the front panel pins to the motherboard?

If not, then the power switch on the case is connected to nothing

this, you dont mention connecting the case switches to the mobo

also I just wanted to throw this out there, I had a system I built that wouldn't power on and I couldnt figure it out. IT turned out that when I installed the mobo, i couldnt get a few screws in so I left them out and the mobo wasn't properly earthed and therefore wouldn't power on! (dont know how because I did have most screws in but after putting in the other 2 I missed, it booted first time)

Contributor

ajcdotme

Posted
Posted

Shouldn't the CPU connector be either 4 pin or 8 pin - not heard of a 6 pin before? You didn't plug in a PCIe power connector to it did you?

They should be keyed to prevent this, but a bit of force easily bypasses this.

Even if shorted on the wrong cpu connector, it should still power up and spin the fans. A mobo should turn over with no valid cpu, but depending on the chipset, it may or may not attempt to post.

I'd short the pins on the psu (with EVERYTHING ELSE disconnected) and see if the fan engages. If it does, I'd attempt to power the board with no cpu or ram (hold the power button down for a period of time here to flush ramdac/caches. possibly manually short the power jumpers on the mobo for a second to power the board to ensure your issue is not a bad power switch)

If all this works, I'd power it off, pull the power, then depress the power button or short the power jumpers with no wall power to flush voltages stored in capacitors. Mount cpu/ram and attempt a POST.

Reply and let us know the progress on these tests?

Enthusiast

teknix360

Posted
  • Author
Posted
Shouldn't the CPU connector be either 4 pin or 8 pin - not heard of a 6 pin before?

Whoopsie! You're correct. It's an 8-pin! I was typing the post from memory.

this, you dont mention connecting the case switches to the mobo

That was it! I was trying to just boot from outside the box (with just mobo, CPU, RAM, and PSU). I was just flipping the power switch on the PSU and nothing was happening. I connected the front panel power switch plug and it booted right up! :woot:

The build I did last year had a power button right on the mobo. It's been so long though, I didn't realize I was missing such an obvious step. :blush: :rofl:

Thanks so much for the help, everyone! I knew you all would figure it out. :wub:

This topic is now closed to further replies.
 Share
Go to topic listing

  • Posts

    • Linux 7.2's first release candidate gets off to a good start

      By zikalify · Posted

      Linux 7.2's first release candidate gets off to a good start by Paul Hill Credit: Larry Ewing It has been a few weeks since the release of Linux 7.1, and in that time, the Linux 7.2 merge window has been open, where developers can submit their features and patches ready for the upcoming release. That window is now shut, and the release candidate phase has begun so that new features can be tested and further fixes applied. According to the founder of Linux, Linus Torvalds, this week’s release candidate looks “reasonably normal”. Although we are super early in the release candidates, this is a good sign as it makes it more likely that an eighth release candidate will not be needed. Torvalds even mentioned that the update’s stats are only larger than they really are because there was another AMD header drop with a third of the patch just being AMD GPU register definitions, which aren’t big changes but make the code contributed look larger overall. In addition to this, he noted that just over half the patch is drivers, even when excluding the AMD register dump. The rest of the changes are spread out over architecture updates, tooling, documentation, and core kernel updates. In the next week, Torvalds says that he will be chilling out, taking the week “mostly off”. Despite this, he will be reading emails and keeping up with things, so if he is slow responding, now you know why. He said he is hoping for a calm week, but we will just have to see if the second release candidate is actually like that. We should expect seven or eight release candidates before Linux 7.2 is released, so expect it around the end of August. If you missed it a few weeks ago, be sure to check out our coverage of Linux 7.1's release.
    • Why it's almost impossible to produce a smartphone in the United States

      By Asgardi · Posted

      Ridiculous claim that the labor cost difference of $6000 annually would increase cost per phone by $200. The employees produce 3 phones per month or what?
    • Sparkle 2.20.1

      By Copernic · Posted

      Sparkle 2.20.1 by Razvan Serea Sparkle is a free, open-source Windows optimization tool designed to make your PC faster, cleaner, and more private. With Sparkle, you can easily debloat Windows by removing unnecessary apps and services, disable Microsoft tracking to enhance privacy, and apply performance tweaks to boost speed. Its cleaner removes junk and temporary files, while every change is safe and fully reversible. Sparkle also features a modern, user-friendly interface with automatic updates, making system maintenance simple. Explore over 39 tweaks, from disabling telemetry and hibernation to optimizing network and game settings, all aimed at customizing and enhancing your Windows experience. Sparkle supports Windows 10 and 11. Sparkle 2.20.1 changelog: You can now change the Animation Direction from Up, Left, or Off. Added configurable animation direction (Up, Left, Off) for improved accessibility Added TTL caching to the system info backend Refactored tweak application flow to await NvidiaProfileInspector Improved IPC listener cleanup to correctly remove specific listeners Fixed online status not updating after successful network requests Updated system info tests to support backend caching Removed electron-toolkit utils dependency in favor of internal is.dev helper Fixed unwanted files and folders being included in application bundles Download: Sparkle 2.20.1 | Portable | ~100.0 MB (Open Source) Links: Sparkle Website | Github | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • The best controller for XBOX and PC is down to the lowest price

      By Figure 8 Dash · Posted

      Never used the G7 Pro, but I've never had a good experience with that style of d-pad and fighting games.
    • Sihoo Doro C300 Pro V2 Ergonomic Office Chair review: The Ikea of chairs

      By Figure 8 Dash · Posted

      And I just bought a seat cushion for my mesh chair. The chair feels nice but the first time I sat in it with boxers, I realized I don't like the feel of mesh on my legs. 😂

  • Recent Achievements

    • One Month Later
      JKR earned a badge
      One Month Later
    • Dedicated
      Asgardi earned a badge
      Dedicated
    • Conversation Starter
      jessse3334 earned a badge
      Conversation Starter
    • Reacting Well
      JuvenileDelinquent earned a badge
      Reacting Well
    • One Month Later
      Excellence2025 earned a badge
      One Month Later

  • Popular Contributors

    1. 1
      +primortal
      496
    2. 2
      +Edouard
      247
    3. 3
      PsYcHoKiLLa
      154
    4. 4
      Steven P.
      86
    5. 5
      macoman
      65
    Show More

  • Tell a friend

    Love Neowin? Tell a friend!