Laptop turned off, now won't even power on


Recommended Posts

The laptop I have (that my family use) is a Dell Studio 1664 that we've had for about 2-3 years now. The battery has been dead for quite a long time, but never has this happened before. My brother was on the laptop, when suddenly it just turned itself off, without warning, and without Windows actually saying that it was going to shut down. Now, it won't turn back on at all. The hard drive is working fine as I have it plugged into my PC as is the power supply. There is absolutely no response at all from the PC when pressing the power button, or when the power supply is plugged into it. I have another Dell laptop (which is also broken) that I have a power supply for and that too does not power it.

I've tried taking the battery out and just using a power supply, nothing. Tried holding down the power button for 30 seconds and only using the power supply, nothing. I really don't know what could have caused this - anyone any ideas at all?

Thanks in advance. :)

The laptop I have (that my family use) is a Dell Studio 1664 that we've had for about 2-3 years now. The battery has been dead for quite a long time, but never has this happened before. My brother was on the laptop, when suddenly it just turned itself off, without warning, and without Windows actually saying that it was going to shut down. Now, it won't turn back on at all. The hard drive is working fine as I have it plugged into my PC as is the power supply. There is absolutely no response at all from the PC when pressing the power button, or when the power supply is plugged into it. I have another Dell laptop (which is also broken) that I have a power supply for and that too does not power it.

I've tried taking the battery out and just using a power supply, nothing. Tried holding down the power button for 30 seconds and only using the power supply, nothing. I really don't know what could have caused this - anyone any ideas at all?

Thanks in advance. :)

Motherboard could of gone bad. I have also seen bad memory cause this issue. Another possibility is the power connector on the motherboard came un soldered.

Try reseating the memory and see if that helps. Otherwise, a repair is going to be expensive.

If your Dell power brick has an LED:

  1. Unplug it from the mains and the laptop
  2. Wait for the LED to go out
  3. Plug the brick back into the mains
  4. Keep an eye on the LED -> plug it into the laptop

If the LED goes out straight away, you have a short of some kind or a loose PSU connector and will need to get it repaired.

If the LED stays on, but refuses to power on when you press the power button, it might be in "fail safe" mode believing there to be a power issue and has switched itself off to protect itself. Leave it unplugged without the battery and press power to use up any residual charge. Give this a few mins then try with just the PSU plugged in.

Either way, either leave a faulty battery disconnected or replace it as it's dangerous and could cause some serious damage.

Another possibility is the power connector on the motherboard came un soldered.

This is what my initial thought was. Try jiggling or pushing down the power connector when connected to the laptop and see if it will power up.

I've seen it happen a couple times and was able to solder it back on, but it's not the easiest task in the world.

This is what my initial thought was. Try jiggling or pushing down the power connector when connected to the laptop and see if it will power up.

I've seen it happen a couple times and was able to solder it back on, but it's not the easiest task in the world.

Not easy, or cheap...unless you know how to do it yourself.

I have a dell laptop at home...its about 3yrs old. It is dead 100 percent. No power, no lights...nothing. Memory was still good as well as the HD. So my problem may be mobo or processor related and sounds like what the user is experiencing as well.

And off topic, I see you live in Milwaukee. I am currently working in Beloit, tho I live in Northern IL.

Not easy, or cheap...unless you know how to do it yourself.

I have a dell laptop at home...its about 3yrs old. It is dead 100 percent. No power, no lights...nothing. Memory was still good as well as the HD. So my problem may be mobo or processor related and sounds like what the user is experiencing as well.

And off topic, I see you live in Milwaukee. I am currently working in Beloit, tho I live in Northern IL.

Yep. Between the time and aggravation that will be spent ripping the thing apart, it's a much better idea to just buy a new one.

Another good idea is to not buy a Dell. :p

Yep. Between the time and aggravation that will be spent ripping the thing apart, it's a much better idea to just buy a new one.

Another good idea is to not buy a Dell. :p

Never really had a problem with Dell myself. Last job we ordered the Latitude lines for 10 years. Only had 2 that needed repair because of a faulty mobo.

I have a Samsung laptop now. Wanted an ASUS but Samsung had a good deal with similar specs and about a few hundred bucks cheaper. So far, works great and no issues. I believe ASUS and even Toshiba are rated the highest.

Motherboard could of gone bad. I have also seen bad memory cause this issue. Another possibility is the power connector on the motherboard came un soldered.

Try reseating the memory and see if that helps. Otherwise, a repair is going to be expensive.

Tried reseating the memory, hasn't worked. Still dead. The power button I have replaced before which goes to connect to the mobo via a ribbon cable, but this time I know it isn't that. Not sure if the power connector is different from this, though.

Just make sure you unplug the power adapter with the battery out and then hit the power button a few times. Then reconnect the power adapter and try it.

Yup, that's the first thing I did but it wasn't having any of it.

If your Dell power brick has an LED:

  1. Unplug it from the mains and the laptop
  2. Wait for the LED to go out
  3. Plug the brick back into the mains
  4. Keep an eye on the LED -> plug it into the laptop

If the LED goes out straight away, you have a short of some kind or a loose PSU connector and will need to get it repaired.

If the LED stays on, but refuses to power on when you press the power button, it might be in "fail safe" mode believing there to be a power issue and has switched itself off to protect itself. Leave it unplugged without the battery and press power to use up any residual charge. Give this a few mins then try with just the PSU plugged in.

Either way, either leave a faulty battery disconnected or replace it as it's dangerous and could cause some serious damage.

The brick that came with the laptop didn't have a brick but I do have another one lying around from another laptop with an LED, but this stayed on when I plugged it in. I've done what you have suggested but still won't respond to anything :(

This is what my initial thought was. Try jiggling or pushing down the power connector when connected to the laptop and see if it will power up.

I've seen it happen a couple times and was able to solder it back on, but it's not the easiest task in the world.

Yeah, it doesn't want to turn on.

I would open it up and make sure the power connector is still connected to the board, it could be that you have a small separate power board not part of the main motherboard you could replace from ebay or something

Otherwise, as above, build a coffin

If its a 3 year hardware, is like 66 years for a notebook :) Not sure where I read that - but like dogs computers years are lots more then just human years..

Battery didn't work anyway - kind of useless as a laptop like that.

I would prob save your time and effort and just get something new. For what its prob used for something very cheap would prob do just fine.. My wife uses her laptop for email, doing jigsaw puzzles and other games while watching tv, email, light browsing, paying the bills, etc. Something in the $300 dollar range here in the US would be more than is needed for such use.

She doesn't need 16gig of ram, she doesn't need latest and greatest 6 core, she needs like no hdd space, etc. If this is what yours is used for - than I would just take any money and time that you would put into fixing this one even if you knew what it was and just put that towards something current.

If my wifes laptop died right now, I would think it could be replaced with a $200 chromebook to be honest. You might want to look into one of those.

I just talked to my brother and he's just told me that the charging light on the laptop was flashing orange after the screen went off - which happens when the battery has run out and Windows puts itself in sleep mode. At the time, the power supply was plugged in and turned on. Because I've tried another PSU on this laptop which also hasn't worked, does that mean that there's something wrong with the power supply connector inside the laptop?

EDIT: Though my other Dell laptop isn't getting powered from my PSU lead...ugh.

Hello,

In addition to the primary battery, notebook computers also have an internal backup battery that provides a trickle of current to the CMOS RAM, which is where the settings for the computer's BIOS firmware are stored, as well as the powering the computer's real-time clock. Most computers these days use a +3.0 Volt DC CR-2032 type battery for this that goes into a slot right on the motherboard, although some laptops may have a tiny wiring harness on theirs in order to move the battery to a more easily accessible location. These batteries used to last for quite some time (five, six, even seven years) due to trace amounts of mercury being added to stabilize the voltage, however, with the introduction of mercury-free batteries several years ago, they are more susceptible to voltage drops earlier on in their life (three years or so), and I have seen systems that would not work with a battery showing +2.975 VDC on a voltmeter.

In any case, I would suggest checking the hardware manual for your Dell Studio 1664 notebook computer to locate where this battery is, check it to see how much voltage it is putting out, and replace it if below +3.0 VDC. They typically cost no more the $3-4 USD and can be purchased wherever batteries are sold (grocer, drugstore, camera store, electronics, big box retailer and so forth) and can be replaced in under ten minutes, with just a small (00 size) Phillips screw driver being used to open the notebook. If the hardware manual says a battery with a wiring harness is needed, go ahead and order that off the Internet.

One a new CMOS/RTC battery is installed, you can try powering up the system on AC power without the primary battery being attached, and see if you can then get into the system. If it boots up, the next step is to replace the primary battery with a genuine one from Dell.

Regards,

Aryeh Goretsky

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Removed the blue and underline as you did not post a link. This would also  be considered spamming.
    • Why it's almost impossible to produce a smartphone in the United States by Hamid Ganji If you look at the back of some Apple products, you can see the famous phrase “Designed by Apple in California, Assembled in China.” This phrase appears on products from one of the largest smartphone brands in the United States. These products are designed in the U.S., but their manufacturing takes place in China, India, Vietnam, or even Brazil. But why can’t Apple, as one of the largest American tech companies, produce its iPhones on U.S. soil? The idea for this topic came to me after the Trump Foundation launched a smartphone called the T1 and claimed that it was designed and built with American values in mind. However, this claim did not last long, as it was revealed that Trump’s phone was actually a rebranded HTC U24 Pro, with only a gold case and minor internal component changes. You see? Even a phone that is supposed to represent American values is manufactured in China. With a gross domestic product (GDP) exceeding $32 trillion, the United States is currently the world’s largest economy, while China ranks second with around $20 trillion. On the other hand, the United States is by a wide margin the global leader in various technological fields, and American companies spend hundreds of billions of dollars annually on research and development. From Apple and Google to Microsoft, Lockheed Martin, Boeing, and others, American tech and industrial giants lead their foreign competitors in many sectors. The United States also has no shortage of smartphone brands. Apple, Google, and Motorola are among the major brands in the smartphone market, collectively holding a significant share. However, the vast majority of their products are manufactured outside the United States. So why is it that the world’s largest economy, home to the most advanced technology companies and industrial powers, cannot produce a smartphone on its own soil? Let’s explore this question together. Even threats to impose tariffs won’t work After Trump entered the White House as the 47th President of the United States, his administration adopted strict tariff policies. One of these policies was the imposition of a 25% tariff on smartphones manufactured outside the United States. Trump said he “had a little problem” with Apple CEO Tim Cook over producing smartphones outside the U.S. So he thought that threatening a 25% tax on imported phones might force Apple to bring manufacturing back to the United States. “I have long ago informed Tim Cook of Apple that I expect their iPhones that will be sold in the United States of America will be manufactured and built in the United States, not India, or anyplace else,” Trump wrote on Truth Social. Image via The White House Although Apple currently manufactures some of the iPhone’s chips in the United States with TSMC's help, it still shows no willingness to shift full iPhone production to the country. At the time, renowned Apple supply chain analyst Ming-Chi Kuo wrote on X, “In terms of profitability, it’s way better for Apple to take the hit of a 25% tariff on iPhones sold in the US market than to move iPhone assembly lines back to the US.” However, manufacturing a smartphone in the United States is not as easy as it might seem, and many technical and economic barriers are involved. The lack of necessary manufacturing hubs There is a clear reason why many companies prefer to manufacture their products in China. China has established itself as the main global manufacturing hub for international companies, and over the past few decades, large contract manufacturers have emerged there, allowing companies like Apple to outsource production. One such example is Foxconn, which also manufactures some Apple products in India. Building the infrastructure required to produce smartphones in the United States would require tens of billions of dollars in new investment. Factories would need to be built, essential manufacturing equipment would have to be installed, and, most importantly, a skilled workforce capable of operating these systems would need to be recruited and trained. The United States currently lacks the core infrastructure needed to manufacture smartphones, and for this reason, many companies prefer to outsource production to Chinese contractors rather than spend tens of billions of dollars to build that infrastructure, which is significantly more economically efficient. Additionally, building such infrastructure in the United States could take up to a decade, ultimately leading to a significant increase in the product's final price for consumers. Shortage of trained labor in the U.S. compared to China Decades of serving as a global manufacturing hub have allowed China to build a massive talent pool in the production sector that is almost unmatched worldwide. Today, if a company chooses to manufacture its products in China, it can be confident that the workers involved in production have years of experience in their respective roles and are capable of producing high-quality goods with minimal errors. Even if we assume that tens of billions of dollars were invested in building smartphone manufacturing infrastructure in the United States, finding skilled workers would remain highly challenging. Apple CEO Tim Cook visiting the iPhone 6 assembly line in China in 2014. Image: Tim Cook on X In a 2015 interview on CBS’s 60 Minutes, Tim Cook said the main reason Apple isn’t producing in the US is a lack of skills. "China put an enormous focus on manufacturing, in what you and I would call vocational kind of skills. The US over time began to stop having as many vocational kinds of skills. I mean you could take every tool and die maker in the United States and probably put them in the room that we're currently sitting in. In China you would have to have multiple football fields,” Cook said. Also, in 2017, at the Fortune Global Forum in Guangzhou, Cook once again emphasized the importance of highly skilled Chinese workers. “China has moved into very advanced manufacturing, so you find in China the intersection of craftsman kind of skill, and sophisticated robotics and the computer science world. That intersection, which is very rare to find anywhere, that kind of skill, is very important to our business because of the precision and quality level that we like. The thing that most people focus on if they’re a foreigner coming to China is the size of the market, and obviously, it’s the biggest market in the world in so many areas. But for us, the number one attraction is the quality of the people,” Apple CEO said. Higher labor costs in the United States Producing almost any product in the United States is more expensive than in many other countries, and one of the main reasons is the higher cost of labor in the U.S. According to the Bureau of Labor Statistics, median weekly earnings of full-time workers in the United States were $1,235 in the first quarter of 2026. Meanwhile, the average annual salary in China's private sector in 2025 was RMB 71,590 (US$9,961). In many parts of the world, the weekly wage of an American worker is equivalent to several months of income. Another important factor to consider is that in the United States, the workforce capable of working on a smartphone assembly line is highly specialized and therefore commands higher-than-average wages. According to an estimate by Bank of America, producing an iPhone in the U.S. is technically possible, but “iPhone cost can increase 25% purely on higher labor cost in the U.S.” However, this 25% increase applies only if final assembly is performed in the United States while components are still sourced from China or elsewhere. In this case, the price of a base iPhone would rise from $799 to around $1,000. But in another scenario, if Apple were to produce the required components for the iPhone within the United States, production costs could increase by more than 90%. Trump’s dream for a “Made in the USA” iPhone might never come true In a free-market capitalist economy, one of the primary responsibilities of any CEO is to maximize profit. Using Apple as an example, Tim Cook’s role is to maximize the company’s profits so that it can fund research and development for new products and invest in areas such as artificial intelligence, while also keeping shareholders satisfied. Therefore, it is entirely understandable that Apple would choose not to bring its manufacturing back to the United States and instead keep production in countries where labor is cheaper, and products can be manufactured at a lower cost, thereby maximizing its profit margins. What is your opinion about manufacturing smartphones in the United States? If you are an American citizen, would you be willing to pay hundreds of dollars more for a smartphone made domestically in the USA? Let us know in the comments.
    • Cheers everyone for the replies. It's been very useful. 👍
  • Recent Achievements

    • Conversation Starter
      jessse3334 earned a badge
      Conversation Starter
    • Reacting Well
      JuvenileDelinquent earned a badge
      Reacting Well
    • One Month Later
      Excellence2025 earned a badge
      One Month Later
    • Week One Done
      Excellence2025 earned a badge
      Week One Done
    • Week One Done
      flexorcist earned a badge
      Week One Done
  • Popular Contributors

    1. 1
      +primortal
      505
    2. 2
      +Edouard
      195
    3. 3
      PsYcHoKiLLa
      153
    4. 4
      Steven P.
      71
    5. 5
      FloatingFatMan
      66
  • Tell a friend

    Love Neowin? Tell a friend!