Laptop turned off, now won't even power on


Recommended Posts

The laptop I have (that my family use) is a Dell Studio 1664 that we've had for about 2-3 years now. The battery has been dead for quite a long time, but never has this happened before. My brother was on the laptop, when suddenly it just turned itself off, without warning, and without Windows actually saying that it was going to shut down. Now, it won't turn back on at all. The hard drive is working fine as I have it plugged into my PC as is the power supply. There is absolutely no response at all from the PC when pressing the power button, or when the power supply is plugged into it. I have another Dell laptop (which is also broken) that I have a power supply for and that too does not power it.

I've tried taking the battery out and just using a power supply, nothing. Tried holding down the power button for 30 seconds and only using the power supply, nothing. I really don't know what could have caused this - anyone any ideas at all?

Thanks in advance. :)

The laptop I have (that my family use) is a Dell Studio 1664 that we've had for about 2-3 years now. The battery has been dead for quite a long time, but never has this happened before. My brother was on the laptop, when suddenly it just turned itself off, without warning, and without Windows actually saying that it was going to shut down. Now, it won't turn back on at all. The hard drive is working fine as I have it plugged into my PC as is the power supply. There is absolutely no response at all from the PC when pressing the power button, or when the power supply is plugged into it. I have another Dell laptop (which is also broken) that I have a power supply for and that too does not power it.

I've tried taking the battery out and just using a power supply, nothing. Tried holding down the power button for 30 seconds and only using the power supply, nothing. I really don't know what could have caused this - anyone any ideas at all?

Thanks in advance. :)

Motherboard could of gone bad. I have also seen bad memory cause this issue. Another possibility is the power connector on the motherboard came un soldered.

Try reseating the memory and see if that helps. Otherwise, a repair is going to be expensive.

If your Dell power brick has an LED:

  1. Unplug it from the mains and the laptop
  2. Wait for the LED to go out
  3. Plug the brick back into the mains
  4. Keep an eye on the LED -> plug it into the laptop

If the LED goes out straight away, you have a short of some kind or a loose PSU connector and will need to get it repaired.

If the LED stays on, but refuses to power on when you press the power button, it might be in "fail safe" mode believing there to be a power issue and has switched itself off to protect itself. Leave it unplugged without the battery and press power to use up any residual charge. Give this a few mins then try with just the PSU plugged in.

Either way, either leave a faulty battery disconnected or replace it as it's dangerous and could cause some serious damage.

Another possibility is the power connector on the motherboard came un soldered.

This is what my initial thought was. Try jiggling or pushing down the power connector when connected to the laptop and see if it will power up.

I've seen it happen a couple times and was able to solder it back on, but it's not the easiest task in the world.

This is what my initial thought was. Try jiggling or pushing down the power connector when connected to the laptop and see if it will power up.

I've seen it happen a couple times and was able to solder it back on, but it's not the easiest task in the world.

Not easy, or cheap...unless you know how to do it yourself.

I have a dell laptop at home...its about 3yrs old. It is dead 100 percent. No power, no lights...nothing. Memory was still good as well as the HD. So my problem may be mobo or processor related and sounds like what the user is experiencing as well.

And off topic, I see you live in Milwaukee. I am currently working in Beloit, tho I live in Northern IL.

Not easy, or cheap...unless you know how to do it yourself.

I have a dell laptop at home...its about 3yrs old. It is dead 100 percent. No power, no lights...nothing. Memory was still good as well as the HD. So my problem may be mobo or processor related and sounds like what the user is experiencing as well.

And off topic, I see you live in Milwaukee. I am currently working in Beloit, tho I live in Northern IL.

Yep. Between the time and aggravation that will be spent ripping the thing apart, it's a much better idea to just buy a new one.

Another good idea is to not buy a Dell. :p

Yep. Between the time and aggravation that will be spent ripping the thing apart, it's a much better idea to just buy a new one.

Another good idea is to not buy a Dell. :p

Never really had a problem with Dell myself. Last job we ordered the Latitude lines for 10 years. Only had 2 that needed repair because of a faulty mobo.

I have a Samsung laptop now. Wanted an ASUS but Samsung had a good deal with similar specs and about a few hundred bucks cheaper. So far, works great and no issues. I believe ASUS and even Toshiba are rated the highest.

Motherboard could of gone bad. I have also seen bad memory cause this issue. Another possibility is the power connector on the motherboard came un soldered.

Try reseating the memory and see if that helps. Otherwise, a repair is going to be expensive.

Tried reseating the memory, hasn't worked. Still dead. The power button I have replaced before which goes to connect to the mobo via a ribbon cable, but this time I know it isn't that. Not sure if the power connector is different from this, though.

Just make sure you unplug the power adapter with the battery out and then hit the power button a few times. Then reconnect the power adapter and try it.

Yup, that's the first thing I did but it wasn't having any of it.

If your Dell power brick has an LED:

  1. Unplug it from the mains and the laptop
  2. Wait for the LED to go out
  3. Plug the brick back into the mains
  4. Keep an eye on the LED -> plug it into the laptop

If the LED goes out straight away, you have a short of some kind or a loose PSU connector and will need to get it repaired.

If the LED stays on, but refuses to power on when you press the power button, it might be in "fail safe" mode believing there to be a power issue and has switched itself off to protect itself. Leave it unplugged without the battery and press power to use up any residual charge. Give this a few mins then try with just the PSU plugged in.

Either way, either leave a faulty battery disconnected or replace it as it's dangerous and could cause some serious damage.

The brick that came with the laptop didn't have a brick but I do have another one lying around from another laptop with an LED, but this stayed on when I plugged it in. I've done what you have suggested but still won't respond to anything :(

This is what my initial thought was. Try jiggling or pushing down the power connector when connected to the laptop and see if it will power up.

I've seen it happen a couple times and was able to solder it back on, but it's not the easiest task in the world.

Yeah, it doesn't want to turn on.

I would open it up and make sure the power connector is still connected to the board, it could be that you have a small separate power board not part of the main motherboard you could replace from ebay or something

Otherwise, as above, build a coffin

If its a 3 year hardware, is like 66 years for a notebook :) Not sure where I read that - but like dogs computers years are lots more then just human years..

Battery didn't work anyway - kind of useless as a laptop like that.

I would prob save your time and effort and just get something new. For what its prob used for something very cheap would prob do just fine.. My wife uses her laptop for email, doing jigsaw puzzles and other games while watching tv, email, light browsing, paying the bills, etc. Something in the $300 dollar range here in the US would be more than is needed for such use.

She doesn't need 16gig of ram, she doesn't need latest and greatest 6 core, she needs like no hdd space, etc. If this is what yours is used for - than I would just take any money and time that you would put into fixing this one even if you knew what it was and just put that towards something current.

If my wifes laptop died right now, I would think it could be replaced with a $200 chromebook to be honest. You might want to look into one of those.

I just talked to my brother and he's just told me that the charging light on the laptop was flashing orange after the screen went off - which happens when the battery has run out and Windows puts itself in sleep mode. At the time, the power supply was plugged in and turned on. Because I've tried another PSU on this laptop which also hasn't worked, does that mean that there's something wrong with the power supply connector inside the laptop?

EDIT: Though my other Dell laptop isn't getting powered from my PSU lead...ugh.

Hello,

In addition to the primary battery, notebook computers also have an internal backup battery that provides a trickle of current to the CMOS RAM, which is where the settings for the computer's BIOS firmware are stored, as well as the powering the computer's real-time clock. Most computers these days use a +3.0 Volt DC CR-2032 type battery for this that goes into a slot right on the motherboard, although some laptops may have a tiny wiring harness on theirs in order to move the battery to a more easily accessible location. These batteries used to last for quite some time (five, six, even seven years) due to trace amounts of mercury being added to stabilize the voltage, however, with the introduction of mercury-free batteries several years ago, they are more susceptible to voltage drops earlier on in their life (three years or so), and I have seen systems that would not work with a battery showing +2.975 VDC on a voltmeter.

In any case, I would suggest checking the hardware manual for your Dell Studio 1664 notebook computer to locate where this battery is, check it to see how much voltage it is putting out, and replace it if below +3.0 VDC. They typically cost no more the $3-4 USD and can be purchased wherever batteries are sold (grocer, drugstore, camera store, electronics, big box retailer and so forth) and can be replaced in under ten minutes, with just a small (00 size) Phillips screw driver being used to open the notebook. If the hardware manual says a battery with a wiring harness is needed, go ahead and order that off the Internet.

One a new CMOS/RTC battery is installed, you can try powering up the system on AC power without the primary battery being attached, and see if you can then get into the system. If it boots up, the next step is to replace the primary battery with a genuine one from Dell.

Regards,

Aryeh Goretsky

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Depends on what you need. Might be a bit clearer on what you plan to do with it. Sort of a waste if you get the newest and greatest, but don't know how to use it.
    • NTLite 2026.06.11200 by Razvan Serea NTLite is a Windows configuration tool that allows you to modify your existing Windows install or an image yet to be deployed, remove Windows components, configure and integrate, speed up the Windows deployment process. Reduce Windows footprint on your RAM and storage drive memory. Remove components of your choice, guarded by compatibility safety mechanisms, which speed up finding that sweet spot. Windows Unattended feature support, providing many commonly used options on a single page for easy setup. Easily integrate a single or multiple drivers, update or language packages. Package integration features smart sorting, enabling you to seamlessly add packages for integration and the tool will apply them in the appropriate order, keeping hotfix compatibility in check. One of the important new features of NTLite (compared to its predecessors) is the ability to modify an already installed the operating system, by removing unnecessary components. Supports Windows 11, 10, 8.1 and 7, x86 and x64, live and image. Server editions of the same versions, excluding support for component removals and feature configuration. ARM64 image support in the alpha stage. Does not support Checked/Debug, Embedded, IoT editions, nor Vista or XP. NTLite 2026.06.11200 changelog: New Secure Boot Migration support: Verification, certificate staging, and boot-manager/sector update across the Image, Updates, Apply, and Create-ISO pages (2023 CA migration, optional 2011 revocation, Anti-rollback, Boot sector choice etc) Secure Boot Host Readiness: Live host Secure Boot migration monitor and Servicing-task control Option under Image page - C:\Windows row, or load the host as the target - Updates - Secure Boot Image: 'Sort mounted images first' option for the image list in Menu-Settings UI: Hover description card for Components and Unattended pages, selectable text and quick access to Compatibility options Command line: Relay commands into the already-running instance Enables controlling already running NTLite via ntlite.exe Use /NewInstance to launch an additional instance using CLI operations (premium) UI: 'New instance' option via main menu instead of a secondary ntlite.exe prompt Apply: Hide individual Apply-page notes with a per-note dismiss (X), critical excluded Settings: 'Unsigned RDP file launch warnings' tweak (RDP client), bypassing the April 2026 security-update prompt on RDP connections Upgrade Image: Live OS and deployed image editing now unlocked on free/test licenses, same licensing as images Image: 'Recompress' option in manual dialog Remove Editions to shrink the WIM in one session Image: SWM part size set inline on the Apply page and image dialogs, split-size popup retired Image: Relative 'Last change' dates; editions grouped by build time to reduce noise Image: 'Forget - Missing' on the Edit-cache menu to mass drop entries whose folder is gone Components: Root groups reorganized - user-facing groups first, system/critical last Components: Show filter options to view components by Template or App-type, since Apps are now merged into groups Presets: Delete confirmation now lists the multi-selected preset names UI: Design update propagated to the rest of the tool UI: Filter and search match words in any order and partially, better results filtering Components Unattended: Input-locale language derives from the user locale, with an independent keyboard picker, enables combinations previously unavailable Unattended: Input-locale now allows for a user value override Unattended: Localization OOBE WinPE now can be copied with the new WinPE Copy OOBE localization toggle, enter locale settings once for both stages Updates: Downloader greys and locks updates the image already carries (hotfix and MSIX) Updates: Resume interrupted update downloads Command line: Many upgrades, see /?, now prints help to the console or redirected output UI-Translation: Finnish language added, also thanks for Chinese Traditional (Matt), French (tistou77), Italian (clarensio), Russian (RDS), Swedish (1FF), Vietnamese (Vu Anh Vu) Fix Components: Containers removal breaking Apps deployment Components: Microsoft Account had leftovers when Easy Migrate is kept Image: Export to an existing WIM improvements, Append renamed to Merge Image: Improved 26H1 live removal support Image: No more 'X:\ not accessible' popup for certain drives during image scan Presets: Manual image refresh picks up presets added/removed outside the app Tweaks: Disabled visual-effect animations no longer return after first logon on a new profile Tweaks: Live Visual Effects toggles (animations, drag full windows, font smoothing) now apply correctly Download: NTLite 2026.06.11200 | 20.5 MB (Free, paid upgrade available) Link: NTLite Home Page | NTLite Features | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • Ah. La Fontana De Incontinentia ! Bella ! Bella !
    • Hi everyone, I'm planning a small network upgrade and was wondering how others prepare their networks for future needs. Do you usually invest in higher-speed switches and better cabling from the start, or do you upgrade only when necessary? I'd be interested in hearing what has worked well for you and any lessons you've learned over time. Thanks!
    • Greetings and welcome!!
  • Recent Achievements

    • One Year In
      BA the Curmudgeon earned a badge
      One Year In
    • Conversation Starter
      rosiecharles earned a badge
      Conversation Starter
    • First Post
      KMilenkoski1202 earned a badge
      First Post
    • First Post
      carols23 earned a badge
      First Post
    • One Month Later
      Tom Willson earned a badge
      One Month Later
  • Popular Contributors

    1. 1
      +primortal
      500
    2. 2
      +Edouard
      257
    3. 3
      PsYcHoKiLLa
      151
    4. 4
      Steven P.
      93
    5. 5
      macoman
      67
  • Tell a friend

    Love Neowin? Tell a friend!