ADSL 2+ internet connection only running slightly faster than ADSL 1 speed


Recommended Posts

I recently upgraded from ADSL 1 to ADSL 2+, however download speed has only increased about 30KB (much lower than expected).

I have tried two different modems - no difference. The internet company can't see any issues at their end.The ADSL 2+ profile is selected on the ISP side.

I have also tried different PCs (including Linux) - all machines download at the same speed.

I checked the wiring in my roof. It's probably 30 to 40 years old. It's all laid out in a straight line, and looks okay. I'm not sure if modern phone cable is any different. Removing the ADSL/phone line filter only increases the speed a few kilobytes. The line coming into the roof (from the termination block outside) is figure-8 cable (just a short length I think).

PCs connect to the modem via Ethernet (I tried different cables too - no difference).

Below are stats from my modem. From this, is there any obvious problems? Do I need to rewire my phone line? Is there any obvious differences between your modem stats and mine?

Statistics--------------Downstream-------Upstream

Line Rate---------------3040 Kbps--------992 Kbps

Attainable Line Rate----3360 Kbps--------1196 Kbps

Noise Margin------------8.8 dB-----------10.0 dB

Line Attenuation--------41.0 dB----------24.5 dB

Output Power------------17.8 dBm---------12.3 dBm

Your stats seem a bit on a bad side. How far away from the exchange are you supposed to be? Anything else on the line that could be affecting it? Fax/other phones not being filtered etc?

How far are you away from the exchange, and what's the general quality of your phone line? The wiring in my house is pretty horrible, but I still get between 6-7Mbps.

Under 10 kilometers away (probably 5). The audio quality on the line is great - no distortion at all.

Your stats seem a bit on a bad side. How far away from the exchange are you supposed to be? Anything else on the line that could be affecting it? Fax/other phones not being filtered etc?

I will find out the exact distance. The only other device is a phone/fax machine, however the problem is still there when it's unplugged.

Perhaps I need to be put onto a new telephone line.

The internet company can't see any issues at their end.
It would be surprising to see one of these companies came forward with their problems. Upgrading means nothing if you are capped by ****/long cabling.

They should sell their stuff with the minimum rates available in the area and and not the maximum rates of the technology used.

3.3 kilometers is the exact distance to the exchange.

I was told a bit more by my ISP this time: ADSL 1 and ADSL 2 work on different frequency spectrums. To get ADSL 2+ speeds, the distance to the exchange needs to be under 2 to 2.5 kilometers.

So, I think I've got to the bottom of the problem. Probably the only solution is to move onto a different ISP.

I will check what my neighbours speeds are.

Thanks all for your help! :)

-----DSL Information-----

DSL Driver Version:A2pD035a.d23f

DSL VPI/VCI:8/35

DSL Status:Up

DSL Mode:ADSL_2plus

DSL UpStream Rate (Kbps):1020

DSL DownStream Rate (Kbps):10937

Down Up

DSL Noise Margin (0.1 dB): 92 112

DSL Attenuation (0.1 dB): 420 258

DSL Transmit Power (0.1 dB): 0 128

thats the best i can sync and im atleast a bit more than 3kms away from mine :/

Well, let me give you some of the info that I found out even thought your in AU. When a telco contractor buries cable, they probably pay per foot the contractor that does it. So even though you are 10km away, they could have buried 20km worth of cable just to make the extra $$. I would also call the telco and have them send someone out to check all the connections around your house, and see if anything is corroded or loose. Then if that doesn't work, run a dedicated wire from the NID to the modem and see what happens. 90% of the time they tell you everything is fine, when in actuality they have a problem but are to lazy or cheap to fix it on their side. I have 6MB/WiMax, and my ISP still tells me nothing is wrong with speed when I can only attain .12MB/down and .26 up.

This topic is now closed to further replies.
  • Posts

    • I imagine that was a review or something? My reviews mostly contain a lot of images and galleries, but these are all webp too, but yeah it all adds up on the page load. Would help if you were more helpful with your critique instead of bitching and moaning like a Karen 😂 Because then we might be able to fix it for you.
    • If Valve refused to let them make the case, I wonder if they've already partnered with someone else to do it? The fact that they didn't seek permission/licence before diving straight in is incredible though
    • OpenClaw now has native mobile apps on iOS and Android by Karthik Mudaliar OpenClaw, the viral open-source personal AI agent, now has its own mobile app, available on both Android and iOS. Users can pair the app with an existing OpenClaw gateway and can start using new mobile-native features that are now available on the app. The app supports all the existing features you'd already have seen on OpenClaw's TUI, as well as some more, such as real-time and background Talk mode, action approvals, sharing from iOS, and optional access to device capabilities such as camera, screen, location, photos, contacts, calendar, and reminders. These features are available on both the Android and iOS versions of the app. What's important with these apps is that they don't run OpenClaw on your phone, but are actually just companion apps that require a running OpenClaw Gateway on an existing device, on macOS, Linux, or Windows via WSL2. To pair the app with your existing OpenClaw gateway, users need to run the command "/pair qr" on the TUI or existing chat interface, which brings up a QR code. Users can then scan this QR code to pair it up with the mobile app. There's also an option to manually pair the app by entering the host and a port. Previously, OpenClaw had been available on phones via WhatsApp, Telegram, Slack, Discord, Microsoft Teams, Matrix, and others. Now, with a native mobile app, the interface is much cleaner and more focused on just the OpenClaw, of course, with the added support for camera, screen, location, and more. It's important to note that OpenClaw comes with its own security warnings. There's always a chance of prompt injection with these tools, so users are recommended to double-check authentication, tool policy, sandboxing, and execution approvals rather than prompts alone. For users well-versed with the AI harness, a native mobile app makes it easier to approve an automation, share a link, use voice, or let an agent react to phone-side context.
    • Google pitches Spanner as one database for all AI agents with these new featues by Karthik Mudaliar Google Cloud is introducing new features within Spanner, its distributed database, as a place where enterprises should keep their data, using which AI agents could make smarter and better decisions. In a detailed blog post, Google highlighted quite a few features coming to Spanner, including relational data, graph relationships, vector search, key-value access, full-text search, and operational analytics together in one database architecture. Google says that today's systems aren't well-made for AI agents. There could be data that is present in one system, search indexes in another, embeddings in a vector database, and relationship data in a graph database. This fragmentation isn't great for AI agents to do their jobs because they don't have access to all of this data in one place. This is where Google is positioning Spanner as a solution. Spanner is already a globally distributed relational database with strong consistency, and Google wants its customers to see it as a broader data layer for AI applications. The company introduced something called Spanner Graph, along with integrated vector search, full-text search, a Cassandra-compatible key-value endpoint, and a columnar engine for analytical queries on operational data. Google also added that its ScaNN-powered vector search can support indexes with more than 10 billion vectors, while the columnar engine can make some analytical scans up to 200 times faster. All of this isn't just exclusive to the Google Cloud Platform, and there's support for multi-cloud as well. This comes via Spanner Omni, which Google says is a downloadable, containerized version of Spanner that can run on Kubernetes and in environments outside Google Cloud, including Microsoft Azure and AWS, and even on-premises infrastructure as well as edge deployments. Google says that customers who are interested in the full-featured edition should contact the company, and there's no word on commercial availability or separate pricing. Those interested can read the full blog by Google Cloud, which details these features individually.
  • Recent Achievements

    • First Post
      rosiecharles earned a badge
      First Post
    • Reacting Well
      Juan Dela earned a badge
      Reacting Well
    • Week One Done
      Collagen Project earned a badge
      Week One Done
    • Reacting Well
      Wakeen1966 earned a badge
      Reacting Well
    • Rookie
      Almohandis went up a rank
      Rookie
  • Popular Contributors

    1. 1
      +primortal
      515
    2. 2
      +Edouard
      273
    3. 3
      PsYcHoKiLLa
      143
    4. 4
      Steven P.
      99
    5. 5
      macoman
      54
  • Tell a friend

    Love Neowin? Tell a friend!