Recommended Posts

Playstation 4 and Xbox 1 may have the headlines right now, however there are other products that were released on this month that are also worth of mentioning. One of them is the new DAP from Sony: the NWZ-F886 which it was released at the beginning of this month (November 2013). This unit was pre-ordered near the close of September from the sony.co.uk site.

 

The Hardware.

 

yc0l.jpg

 

-From left to right: Sony Walkman NWZ-F886, Sony XBA-30 Balanced Armature Headphones, CKH-NWF880 Plastic Cover and Screen Protector.

 

qlbn.jpg

 

-The packaging is quite easy to open and there is no need to rip it apart.

 

4zy5.jpg

 

-With both the plastic cover and the screen protector set. The pouch on the left is given with the XBA-30 headphones so it is possible to store and protect them.

 

flqv.jpg

 

-It turns on no problem, not blinking blue lights or any other similar behaviour.

 

First Impressions.

 

The first thing can be noticed when the device is just turned on and it reaches the android desktop is the screen... it is stunning. Admittedly, compared to a PSVita the OLED screen looks better, but the screen on the NWZ-F886 is very close to it, perhaps the most noticeable difference are the blacks, which are a little less on the Walkman and well defined on the vita. Yet the impression stills there.

 

Second thing are... real buttons! Yes, This little handy device possess the extremely useful set of: Previous button, Play Pause button, Next button and volume controls but more on that later.

 

Third thing is size and weight. The size of it is comparable to my Motorola RAZRi XT890, it is however, very light even with plastic cover attached.

 

Fourth thing is that it has a metallic or a very convincing metallic body on the back, except for the NFC part, giving it a very premium fell.

 

5itz.png

 

-Not formal screen comparison between the PS Vita, the Walkman NWZ-F886 and the RAZRi (Pentile Screen) (Also size). All the devices are set to 50% brightness.

 

Usability.

 

The player has been tested for around a week, mostly playing music files. Said files are AAC 192 Kbps.

 

First, I had to load the whole library of my previous Walkman, the formidable NWZ-S545:

 

pnu4.jpg

 

-The veteran NWZ-S545 Walkman. This version had 16 GB of internal memory and was replaced by the NWZ-F886 since the memory was almost full.

 

The library consisted of around 2700+ sounds, which the database of the NWZ-F886 took 1 minute to process. It is quite fast and the device shows you that it is doing that on the notification bar, simply by showing "Updating Database..." and after that it's ready to go.

 

The Walkman Application.

 

Pre-installed in the device comes the Walkman Application for playing the music files, it can be accessed by either the widget on the android desktop or the lower left shortcut, left to the all apps android button.

 

rnlk.png

 

-Main screen and short-cuts.

 

Once opened, the following screen can be seen:

 

x65n.png

 

-Walkman main screen.

 

At first a pop-up screen will appear explaining the controls shown on screen, just pressing ok dismisses it. As it is if the play button is pressed, it simply starts playing all the music on the device. the shuffle icon above the "next song" button can be conveniently toggled on and off, same with the icon on the right. Swiping right shows the information of the song that it's currently being played:

 

e1z0.png

 

-Current song properties.

 

Whilst swiping left shows the current play list, note that this will change if the shuffle option is activated.

 

u3og.png

 

-Play list screen.

 

Pressing the upper left screen button of the Walkman application allows to select other songs, according to album, artist... etc. A particular welcomed option is the one that allows playback by folders:

 

h3p2.png

 

-Playback mode selection screen. Note that this has been changed to only shows those three options but this can be modified.

 

Selecting the three squares column on the upper left brings even more options:

 

tb2x.png

 

-Options of the Main Screen.

 

Which leads us to the Sound Adjustment part and from there a very familiar screen:

 

ivl5.png

 

-Equalizer Screen.

 

aj0h.png

 

-Other options within the Sound Enhancements tab.

 

Note that the physical playback buttons on the device are very usable with the device either locked or either unlocked. When locked, the player is still responsive to the buttons, so it's possible to let the screen to turn off itself and the playback doesn't stop. The only way to turn on the screen is using the physical power button on the top of it.

 

Audio Quality.

 

The NWZ-F886 belongs to the audiophile range. It sports a new S-Master HX amplifier, created for this device and the NWZ-HX1. The XBA-30 earphones are known to have a plain curvature response (no v-shaped, i.e. no bass or treble emphasis), which coupled with this device and all of the audio enhancements disabled offered the following particular experience:

 

Bass is dry and clear, treble is crisp, mediums and vocals sound phenomenal. It is a great upgrade from the NWZ-S545, which unfortunately could not drive the XBA-30 for direct comparison (bass was completely missing) Overall is a very neutral player with an excellent soundstage.

 

Note that the Balanced Armatures in the XBA-30 refer to another type of "speakers" within the earphone, instead of using cones, it uses very thin plates to generate sound. The XBA-30 processes 3 Balanced Armatures, one for bass, another for medium frequencies and a last one for treble. The effect on this is a very wide soundstage on the device, meaning that a lot of instruments can be differentiated from each other and there is not muffling on them, e.g. when bass is very strong the other instruments don't fade.

 

Peripherals.

 

With a device like this it may be expected to have a camera, however, this is not present in it. Being a dedicated DAP however this is to be expected, nonetheless due its wireless capabilities and NFC, paring an external camera is fast and reliable:

 

w9j1.jpg

 

-The DSC-QX100 camera attached to the NWZ-F886.

 

This is possible using either a QX10 or QX100 camera and the PlayMemories mobile application from the Android Store:

 

sl4u.jpg

 

-PlayMemories Mobile acts as the screen of the QX-100 Camera.

 

A particular improvement of this camera in the NWZ-F886, compared to using it with the XT890 Motorola RAZRi phone, is that whilst the former offers a seamless experience (no hiccups) the latter suffers from pauses of up to two seconds at random intervals, thus the experience using the QX100 with the NWZ-F886 is far better. The quality on the photos is also impressive, as it can be seen in this very own article where the Logitech C920 Webcam photos can be easily discerned from the ones of the QX100.

 

Android and Battery Usage.

 

The NWZ-F886 comes with Android 4.1.1:

 

esil.png

 

-Android "About Device" Screen

 

This android version has been little modified, almost the vanilla experience. There are no other pre-installed programs other than the Walkman application, a photo viewer, a video player and a radio application. Hence the device feels very responsive. It is of interest the Application RAM consumption shown in Android:

 

lj1u.png

 

-Android Application RAM consumption.

 

This is because whilst the device is known to have 1 GB of memory, the total RAM displayed doesn't add up, an hypotheses of this might be that the Walkman Application is running on memory, but this cannot be seen by the end user, perhaps that may explain why it is possible to use the hardware buttons without waking up the device. As for the battery consumption it can be said that it is excellent so far:

 

phru.png

 

-Battery consumption screen.

 

The device was charged up to 100% around Saturday 8 am and then unplugged from the mains. On Monday, 11 hours later (97% battery) the device was taken to a field trip, which was 30 minutes to go and 45 to return, all of which the player remained playing shuffled music whilst constantly pressing the next button to hear the next song faster (sometimes songs were skipped altogether) and was left locked the rest of the day (87%), the next day two trips taxed another 2:30 hours on continuous play and finally on Wednesday (today) at around 12 pm after an email check and a fast web-page checking the battery remained at 56%.

 

Android, Other Programs.

 

The next screen displays some of the current programs installed on the NWZ-F886:

 

pu58.png

 

All of them which work fine, there is also the "Power Toggles" application, hidden in the notification bar. This program is very useful to lock the device without pressing the power button, as well for controlling brightness and other handy short-cuts. It also works no problem.

 

PowerAmp also works, however, hardware buttons then to obey the Walkman application rather than PowerAmp.

 

Closing Thoughts.

 

The Walkman NWZ-F886 is an excellent device for its purpose: listening to music with high-fidelity. It is not a flagship Android device, but it avoids a lot of problems, such as the ones shown in http://www.youtube.com/watch?v=_EKAp1yZDhM#t=853, thanks to a very mature OS and the Walkman Application. Of course it also offers the versatility of many applications on the Android store, however, it is still mainly an audiophile DAP.

 

It does not have expandable memory, however being the case that this Walkman can support external DACs using the cable http://www.sony.jp/walkman/products/WMC-NWH10/store-w/ , it's highly feasible that in future some sdcards adaptors may appear.

 

This device has a WM port in it rather than a standard USB, this has been always the case with the Sony DAPs with a few exceptions, however the cable is included and no further difficulty is found using it.

 

Overall an excellent choice for the Audiophile crowd at an affordable price. Highly recommended, specially with its price tag of 224 Pounds (using academic discount) at the Sony store.

 

Edit: Please feel free to ask any questions about the device.

Link to comment
https://www.neowin.net/forum/topic/1188991-the-sony-walkman-nwz-f886-review/
Share on other sites

my last walkman was the original k7 one..  :D

 

anyways, this is a very good looking one.

 

I never had a walkman... until I got the Hi-MD MZ-NH700, boy that thing was great.... sadly I never had a Hi-MD disc, I only had the original discs that were of less capacity, nonetheless it worked fine and sounded great, from that went to a PSP and from there to the NWZ-S545, all of them were great sounding devices.

Impressive review, the only problem I can see with it is the android OS. I tested one at my local CEX, (sorry I don't remember the exact model) and it was no louder than my s3.(a hell of a lot quieter than my old aiwa cassette walkman)

Which is a pity as I loved it

Nice review! Kind of sad that DAP's went away from the mainstream market and has entered the niche audiophile market once again. I guess it got lost in the world of convergence devices :(

It has sense... not many people cares about the difference between mp3, aac and flac (sadly). Those who do on the other side had only very limited options, sony in this case seems to have hit very well, covering a bit of the mainstream market (Android) while remaining audiophile (The new SMaster HX amp). They really know "how to audio" in this case.

Great work on the review.

 

I think Sony should retire the Walkman brand. It is a great brand, but it seems entirely dated. When I hear walkman I think 80s-90s & that sloooow down sound they made when the batteries were dying.

Great work on the review.

 

I think Sony should retire the Walkman brand. It is a great brand, but it seems entirely dated. When I hear walkman I think 80s-90s & that sloooow down sound they made when the batteries were dying.

Never, if precisely the Walkmans are known for something, is that, regardless limitations, sound quality has been always above the average.

This topic is now closed to further replies.
  • Posts

    • When I think about a network, there are really two aspects, the hardware and the wiring. So here is what I would do for both. Wiring: Use Cat6A for the patch panel and all structured cables (cables installed in walls). Run plenty of Wireless Access Point (WAP) cables, as a general rule, assume a signal can only pass through 2-3 walls and can't pass through a floor (that is conservative, but trust me on this if you want strong WiFi)  Cat6 patch cables are fine for now if you don't plan to run 10gig, those are easy to replace later if needed. Run OS2 single-mode fiber to anywhere you think you may have a server or sub-switch. (yes, single-mode for everything on a small network, don't mess with multimode unless you have entire racks of servers and that minor module cost and power savings will matter). If you really want to future proof, also run fiber to any high density WAP locations, it is likely that WiFi 8 WAPs will push the limits of 10g. Run 6-12 pairs of single-mode fiber between your MDF and the building's MDF, even if you only need 1 or 2 pairs now, those extra pairs will pay off down the road. Hardware: (its easy to say "get all the features incase you need them", so instead of futureproofing, I am going to take approach of suggesting areas worth investing in, and areas you can save money). Don't overspend thinking you need every feature on every port. You don't need 10g on every port, you don't need PoE on every port. Don't overspend on redundancy either, unless you are ready to buy two of everything, don't waste money buying two of some things and not others. Dual power supplies are worthwhile, but probably not HA or multi-path redundancy.  Get 1 "distribution layer" switch that your router/firewall will connect to, your access layer switches. This should be a 10g switch with a combination of copper and SPF ports and should be a fully managed switch. Given that you said it is a small network, I suggest also using that distribution layer switch for servers and WAPs, meaning it will need PoE. Speaking of wireless, get good professional tri-band WAPs, and either turn on the band stirring options, or limit 2.4 to an IoT only SSID. This will provide a solid WiFi capable nearly everything but the highest of bandwidth clients...you could even consider skipping wiring workstations depending on usage. Access layer switch for workstations and printers can be cheaper switches, 2.5g is a good sweet spot between price and future proofing, but even 1g is fine for most individual clients (the kind that could probably be fine on WiFi). You can consider saving a little on access layer switches by only getting 1 PoE switch for whatever needs it (remember your WAPs are connecting to the distribution switch, not here), and non-PoE for your workstations, because desk phones are falling out of favor. You can also save money here by not buying managed switches if you don't need them--but really do some soul searching there, if you go this route, then anything that isn't on your workstation VLAN would either need to be connected to the distribution switch, or its own switch. Also, don't feel like you need a fancy fabric stacking switches for your access layer, that is the point of the higher-end distribution layer, to remove the need for things like that at this level. Home Hardware: I'm realizing the above assumed an office setting, if this if for your house and home lab then the above still applies, but you'll probably want everything managed and PoE, just because, but you probably also don't need multiple access layer switches. if your total port count is below 24, just skip separating distribution layer and access layer and just get one nice switch with the features you want. For home use, don't worry about home running every device to the main switch, there is nothing wrong with running sub-switches for your media areas and office, those essentially become your access layer, just look for sub-switches with a 10g uplink so sharing bandwidth isn't an issue.
    • Google Meet brings Gemini note-taking to AI Pro and Ultra subscribers by Karthik Mudaliar Google's Gemini-powered "Take notes for me" feature inside Google Meet is now available to Google AI Pro and Ultra subscribers. The features work on Google Meet for web as well as on mobile, and Google says that subscribers can use it for meetings they host in many supported languages. As the name suggests, "Take notes for me" allows Gemini to listen to a meeting, generate a summary, identify action items, and save the notes as a Google Doc in the user’s Drive. After the meeting, the organizer receives an email recap with the summary and action items, while the notes can also be attached to the related Calendar event depending on the meeting setup and sharing settings. The feature isn't automatically turned on for everyone, though. Google says that all meeting participants are notified when note-taking is turned on, and users can start it from the pencil icon in Meet or enable it for future calls through Meet’s meeting records settings. For work or school accounts, administrators can also control whether the feature is available and may require explicit participant consent for note-taking, recording, or transcription features. The feature first launched back in 2024, when it was available just for selected Workspace users. Over the years, Google added refinements and more options, including the ability to enable it when scheduling meetings via Google Calendar. Google's support docs say that the feature currently supports English, French, German, Italian, Japanese, Korean, Portuguese, and Spanish, but only one language at a time. Meetings with multiple spoken languages are not currently supported, and Google recommends using the tool for meetings between 15 minutes and eight hours. The new feature makes Google Meet closer to its rivals that have AI tools already built in. Microsoft Teams has recently started offering Copilot and intelligent recap features that summarize meetings, surface highlights, and help with follow-ups, while Zoom’s AI Companion can also generate meeting summaries from desktop and mobile meetings.
    • GnuCash 5.16 by Razvan Serea GnuCash is a personal and small business finance application, freely licensed under the GNU GPL and available for GNU/Linux, BSD, Solaris, Mac OS X and Microsoft Windows. It’s designed to be easy to use, yet powerful and flexible. GnuCash allows you to track your income and expenses, reconcile bank accounts, monitor stock portfolios and manage your small business finances. It is based on professional accounting principles to ensure balanced books and accurate reports. GnuCash can keep track of your personal finances in as much detail as you prefer. If you are just starting out, use GnuCash to keep track of your checkbook. You may then decide to track cash as well as credit card purchases to better determine where your money is being spent. When you start investing, you can use GnuCash to help monitor your portfolio. Buying a vehicle or a home? GnuCash will help you plan the investment and track loan payments. If your financial records span the globe, GnuCash provides all the multiple-currency support you need. Between 5.15 and 5.16, the following bugfixes were accomplished: Bug 421610 - RFE: Include logical dates for View->Filter by "date range"The Select Range section of the Date tab of the register's Filter By dialog box is changed to provide relative, specific date, or days ago options for the start and end of the filter range. The Show number of days item label is changed to Show from days ago to better reflect what it does. Bug 436105 - esc key not working as expected in register: Enable the escape key to cancel a field edit. Bug 797384 - Gnucash doesn't handle commodity prices with big numerator/denominator properly. Bug 798004 - Next gen UI for stock transactions Bug 799314 - Add "enter now" option in scheduled transaction editor. tab to allow users to select the scheduled transactions to be included in a “Since Last Run…” window. If there are no instances of a selected transaction triggered by today’s date, the next instance is triggered. Bug 799751 - autocomplete crash Bug 799759 - Users can't Enable entries via Checkboxes on Scheduled Transactions PageAllow the Enabled box in the list of scheduled transactions to be operated instead of having to open the transaction editor dialog and change the Enabled checkbox. Also added use of the Name column as the secondary column sort for all the other columns. Bug 799762 - Poor handling of cases where hidden/placeholder accounts are used in the account register Bug 799766 - Double line preference not respected in search register Bug 799767 - POST /accounts in bindings/python/example_scripts/rest-api is broken Bug 799777 - `xaccSplitSetParent`: reparenting a committed split silently drops its KVP slots (online_id, cap-gains links) Other changes & improvements: Numeric values may now be selected to copy in the Accounts page. Add new Finance::Quote source Finnhub.io: Free API key (personal/non-professional use) available at https://finnhub.io. Set FINNHUB_API_KEY environment variable to API key to use this source. As of June 2026, free tier API limit is 60 API calls/minute. The Investment Lots report has new optional columns for Computed Annual Growth Rate. Python Bindings: Improved translation of primary object (Account, Transaction, Split, etc.) so that they can be treated as normal Python objects. This is accomplished with SWIG magic so no existing code is obsoleted. Python Bindings: Better conversion of GLists to Python lists. Python Bindings: Destroy the QofSession in the Python Session dtor to prevent leaving the database locked. [engine] Add first-class online_id accessors for Split and Account and make them available to Python bindings, removing the unused Transaction online_id property. Improve C++ implementation of QofBook. Correct the Doxygen doc for qof_instance_get/set_kvp. [gnc-log-replay.cpp] fix incorrect guid dump Add some Boost library requirements needed by libgnucash-guile to CMakeLists.txt so that missing feature will fail at configure time. Use Compile-time Regular Expressions instead of std::regex in gnc-filepath-utils.cpp and instead of boost::regex in the CSV importer, with the CTRE v3.11.1 header added to borrowed [gnc-filepath-utils.cpp] null check char* arguments Add ChartJS licenses. Removed AEX from list of commodities. euronext.com is now using JS based anti-webscraping. [report-core] always offer options summary in reports. This is useful to debug reports. The Add options summary option is removed because it's no longer optional. Remove remaining obsolete IMContext from sheet Fix blurry text in HiDPI offscreen-rendered widgets Add port field to database connection dialog: The convention of appending the port number after the host isn't obvious. When editing a split in the register treat the account as being changed only if it isn't the one selected before editing instead of if the user performed an edit Return immediately from qof_book_destroy if hash_of_collections is null. If qof_book_destroy is called on a QofBook* freshly created with qof_book_new (usually because it was used to create a session that now must be destroyed) it would try to empty the non-existent hash tables, crashing. Clean up Flathub metadata to solve warnings at flatpak build time. Be consistent in naming GncPluginPage and GncPluginPageRegister HTML: Remove unimplemented function declarations. [gnc-html.cpp] remove unused buggy string conversion functions Convert libgnc-html to C++ Apply -Wall -Werr -Wmissing-prototypes to C++ compilation on Windows and fix the resulting errors. New and Updated Translations: Arabic, Croatian, Danish, Dutch, German, Finnish, Hungarian, Korean, Norwegian-Bokmal, Spanish Download: GnuCash 5.16 | 176.0 MB (Open Source) Links: GnuCash Home page | Other Operating Systems | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • Microsoft finally launches WSL Containers in public preview by David Uzondu Microsoft has announced that WSL containers, a feature that allows developers to run Linux containers natively inside Windows without the need for Docker Desktop, is now available in public preview several weeks after Microsoft previewed it at Build 2026. To use the new container feature, you first have to install the latest pre-release version of the Windows Subsystem for Linux by running a quick update command in your terminal: wsl --update --pre-release After installing, you'd get access to the new Linux container CLI (wslc.exe) and the programmable API. Microsoft said that the CLI has a "familiar format" that matches the toolsets developers already use every day. If you know standard Docker commands, your muscle memory will translate directly to wslc.exe, which even features a built-in alias called container.exe. You can quickly run a full Ubuntu KDE desktop container by exposing ports, or pass your graphics card straight into a machine learning environment to run PyTorch workloads. Passing the --gpus all flag inside the run command instantly links your hardware. Image via Microsoft As for the API, developers can now embed Linux container operations directly inside native Windows applications without exposing the command line to users. The team integrated the API directly into MSBuild and CMake, so developers can define container steps directly in project files. Apart from bringing the CLI and API into public preview, Microsoft also said that it's working on a new default file system called virtiofs to speed up file transfer rates between Windows and Linux. Microsoft also introduced an experimental networking mode named consomme, which resolves compatibility issues with corporate VPNs by routing Linux network traffic straight through Windows. One thing to note about WSL containers is that they don't run in your standard WSL distributions; instead, every application and CLI session spawns its own lightweight Hyper-V utility VM in the background. This basically reduces the chances of one app snooping on the container of another app.
    • Google reportedly limited Meta's Gemini access over limited AI compute by Karthik Mudaliar Google is reportedly limiting Meta's use of its Gemini AI models after Meta tried buying more computing capacity than even Google could supply. According to the Financial Times, Google told Meta in March that it could not provide the full Gemini capacity that Meta had requested. This shortfall even disrupted and delayed some of Meta's internal projects. Due to this, Meta even told its employees internally to use AI tokens more efficiently. Meta wasn't the only one to get hit by this sudden refusal by Google; even other customers were affected. But Meta was hit harder because of its unusually high demand for Google's models. The move from Google makes it evident that companies all over are in limited supply of both infrastructure and compute. Alphabet said in April that Google Cloud revenue grew 63% year-over-year to $20 billion in the first quarter, helped by enterprise AI infrastructure and AI solutions. In pursuit of more compute, Meta had earlier signed a multi-billion-dollar AWS agreement as well as a large AMD GPU deal for AI data centers. But the crunch would be short-lived as both Meta and Google have also ramped up infrastructure investments heavily. Meta said in November that it was committing more than $600 billion in the U.S. by 2028 for AI technology, infrastructure, and workforce expansion. In the first quarter of this year, Meta also raised its expected capital expenditure for 2026 to a range of $125 billion to $145 billion, citing higher component pricing and additional data center costs for future capacity. However, this doesn't make the company immune to the current dependence on outside suppliers. Meta has also spent many years promoting Llama as an open-weight alternative to closed models from Google, OpenAI, and Anthropic. But if the reported reliance on Google's Gemini models is severe enough for internal work to get impacted, then it looks like even frontier labs and Big Tech aren't fully self-sufficient. Source: Financial Times
  • Recent Achievements

    • Reacting Well
      NovaEdgeX earned a badge
      Reacting Well
    • Week One Done
      NovaEdgeX earned a badge
      Week One Done
    • One Year In
      BA the Curmudgeon earned a badge
      One Year In
    • Conversation Starter
      rosiecharles earned a badge
      Conversation Starter
    • First Post
      KMilenkoski1202 earned a badge
      First Post
  • Popular Contributors

    1. 1
      +primortal
      533
    2. 2
      +Edouard
      269
    3. 3
      PsYcHoKiLLa
      150
    4. 4
      Steven P.
      98
    5. 5
      macoman
      66
  • Tell a friend

    Love Neowin? Tell a friend!