Recommended Posts

So i've started having issues with my controllers where they don't sync with the PS3 until i connect them using a USB cable. They're ok after i unplug the cable but whenever i next turn on my PS3 again i still get the same problem.

 

It doesn't seem like a bluetooth issue because if i get one controller working using the above method then the other two sync straight away without even having to connect them by USB.

 

I tried the pin reset buttons on the back of the controllers and even going into safe mode and restoring the file system (it did say it was corrupt and would be rebuilt) but now i'm out of ideas as to what to do. Can anyone help?

Link to comment
https://www.neowin.net/forum/topic/1198785-ps3-controller-sync-issue/
Share on other sites

  On 30/01/2014 at 20:57, red. said:

So i've started having issues with my controllers where they don't sync with the PS3 until i connect them using a USB cable. They're ok after i unplug the cable but whenever i next turn on my PS3 again i still get the same problem.

 

It doesn't seem like a bluetooth issue because if i get one controller working using the above method then the other two sync straight away without even having to connect them by USB.

 

I tried the pin reset buttons on the back of the controllers and even going into safe mode and restoring the file system (it did say it was corrupt and would be rebuilt) but now i'm out of ideas as to what to do. Can anyone help?

 

Are they defaulting to the same number when you try to sync them without the USB cable?

  On 30/01/2014 at 21:14, D. S. said:

Are they defaulting to the same number when you try to sync them without the USB cable?

 

Whenever i press the PS button while the PS3 is on standby, it will turn the console on like normal bit the controller lights will just keep flashing and not sync from then on.

  On 30/01/2014 at 21:31, red. said:

Whenever i press the PS button while the PS3 is on standby, it will turn the console on like normal bit the controller lights will just keep flashing and not sync from then on.

 

Are they all assigned different numbers in Accessory settings? What happens if you press the PS button again while the lights keep flashing? No effect?

  On 30/01/2014 at 20:57, red. said:

So i've started having issues with my controllers where they don't sync with the PS3 until i connect them using a USB cable. They're ok after i unplug the cable but whenever i next turn on my PS3 again i still get the same problem.

 

It doesn't seem like a bluetooth issue because if i get one controller working using the above method then the other two sync straight away without even having to connect them by USB.

 

I tried the pin reset buttons on the back of the controllers and even going into safe mode and restoring the file system (it did say it was corrupt and would be rebuilt) but now i'm out of ideas as to what to do. Can anyone help?

 

I bought 3x supposedly broken PS3 controllers off of eBay recently and 2/3 of them (older model DS3) had similar issues to this with my PS3 (CECHC04).

Here's what fixed it for me:

  • Turn on PS3 via power button
  • Plug in PS3 controllers via USB simultaneously (I had 4x DS3 on 4 separate USB cables for mine)
  • Turn them on, one by one
  • Let them charge for a moment each
  • Power down each controller in turn via holding the PS button, select turn off controller
  • Shut down PS3
  • Test each controller
  On 30/01/2014 at 21:34, D. S. said:

Are they all assigned different numbers in Accessory settings? What happens if you press the PS button again while the lights keep flashing? No effect?

I haven't checked the settings with all controllers plugged in. If I press the PS button while USB is plugged in then it successfully syncs but if not plugged in then it continues to flash all 4 lights.

  On 30/01/2014 at 21:49, Aergan said:

<p>

I bought 3x supposedly broken PS3 controllers off of eBay recently and 2/3 of them (older model DS3) had similar issues to this with my PS3 (CECHC04).

Here's what fixed it for me:

  • Turn on PS3 via power button
  • Plug in PS3 controllers via USB simultaneously (I had 4x DS3 on 4 separate USB cables for mine)
  • Turn them on, one by one
  • Let them charge for a moment each
  • Power down each controller in turn via holding the PS button, select turn off controller
  • Shut down PS3
  • Test each controller

Thanks. I'll try this tomorrow. I got fed up and gave up for tonight.

  On 30/01/2014 at 21:49, Aergan said:

 

I bought 3x supposedly broken PS3 controllers off of eBay recently and 2/3 of them (older model DS3) had similar issues to this with my PS3 (CECHC04).

Here's what fixed it for me:

  • Turn on PS3 via power button
  • Plug in PS3 controllers via USB simultaneously (I had 4x DS3 on 4 separate USB cables for mine)
  • Turn them on, one by one
  • Let them charge for a moment each
  • Power down each controller in turn via holding the PS button, select turn off controller
  • Shut down PS3
  • Test each controller

 

 

Just a quick question, how were you able to plug all the controllers in at the same time? As far as i can see the super slim only has 2 USB ports.

Try deregistering them, then one by one, plug them back into the ps3 via usb one at a time

 

assign a position for it (ie controller 1)

then use the ps button on the controller to turn off the ps3.......... after everything turns off, try turning on the ps3 via the ps button on the controller

 

once that's done, assign your subsequent controllers, and once all controllers are registered to the console, turn off again from the ps button from any controller this is important as mine used to do that too

the only fix I found that worked for me was to do this, it'll re assign controllers, nothing you can do about that, but it should then turn off and then back on from any of the controllers 


  On 31/01/2014 at 08:52, red. said:

Just a quick question, how were you able to plug all the controllers in at the same time? As far as i can see the super slim only has 2 USB ports.

on any ps3 that isn't gen 1 60 gig, you can't, (unless using a usb hub) the only way is to leave them on, and lets the console decide how it's going to handle them (I believe)

 

Hope this helps :)

Tried everything posted and nothing worked :( Strangely if i go into safe mode the controllers sync fine, when it boots normally it doesn't.

 

Also, when i go to repair the filesystem, it keeps saying it's corrupt and needs fixing. I've done it twice and it doesn't seem to be changing.

  On 31/01/2014 at 20:48, red. said:

Tried everything posted and nothing worked :( Strangely if i go into safe mode the controllers sync fine, when it boots normally it doesn't.

 

Also, when i go to repair the filesystem, it keeps saying it's corrupt and needs fixing. I've done it twice and it doesn't seem to be changing.

Sounds like the controllers might not be your issue, do you have a suitable flash drive to download the latest firmware from the sony website to reformat the console?

and back stuff up etc...?

  On 03/02/2014 at 11:03, red. said:

Strangely, without me doing anything, the controllers are syncing again. Not sure what's changed but just as suddenly as it stopped working it's now working again. :s

 

Gremlinelectricql8.jpg

  On 01/02/2014 at 09:56, red. said:

I do, I was hoping avoid backup and formatting as I have a lot of stuff on the hard drive and the Super slim doesn't seem to be able to pick up my USB powered external hard drive.

(I feel your pain bro, and when my slim does, it for no reason restarts the hard drive's spoolup process for no reason)

This topic is now closed to further replies.
  • Posts

    • I agree with your points, particularly around workflows. But I think this is a symptom of the way Microsoft plans, builds, and releases its OS's, not about its UI ideals itself. It has historically been large jumps in UI changes between releases, XP > Vista > 7 > 8 were ALL significant changes in how we performed tasks. Then Win10 was released and updated twice a year with minor changes. This was somewhat nice as the changes were often minimal, however as it looked like the same OS for the most part, when something did change (like the start menu), it was a bit confusing for people who didn't understand that they had actually been upgraded, and why just this one key part had changed. But I believe that was too slow, and didn't allow their future designs to be played out in that structure. So the "last Windows version ever" was superseded with a new UI and overhauled once more. It too has changed quite a bit in its 4 years, but I think there needs to be an understanding of that change, which I guess we have in the "24H2" version numbering, but not in the marketing that most users know. The most consistent and clear communication of changes I think is done with MacOS. While I'm not a fan of Apples software, their clear and consistent release schedule, and progressively planned changes to the OS is concise and clear, leading towards a well thought out goal to their users with branding the big updates, but more subtle of changes confined to those releases. Windows 10/11 version updates just get lost in the vast collection of update types in Windows Update, and as such most users wouldn't know if the were on 22H2, 23H2 or 24H2, or even know what those meant. I think we will see Microsoft drop the Win11/Win12 branding once Windows 10 has finally died. And hopefully, make it a bit more consistent with feature/UI updates sticking to an improved branded version/year release rather than "moments" or just randomly enabled elements in a random monthly update. Until then, even us tech users rarely know what features are in what release and if we will see it on our own computers. Get with it MS!
    • Hello, Horizon Data Systems, the developer, has been around for 27 years.  I do not recall hearing anything bad about them, but I also haven't used their software, either. Regards, Aryeh Goretsky  
    • Hello, I am wondering if this will go through an appeal process, or if the ruling is final? Regards, Aryeh Goretsky
    • Hello, I think it also depends upon what sorts of software you develop. My employer makes software that does rely on operating system version-specific functionality, and that is typical and normal behavior for our industry. While we do provide support for older versions of operating systems, it is only for a certain amount of time. If you still want to use our software after that, it becomes a custom support package, which isn't cheap. Regards, Aryeh Goretsky
    • Ok Mr lawyer, what violation or damage is done to requiere a regulation? I get your point but you need more valid points what and how regulations are done. Just google it. Hence me saying Mr Lawyer. I didn't learn new things just by saying big random words, I actually acknowledged and read on what they meant and work. Let's not forget there are national and there are international laws and also violations. For something to have a regulation effect, there must be some sort of damage. Sorry to tell you but annoyance isn't considered consumer damage. Apple changed to USB-C because of the EU and it caused a chain reaction to other countries but those other countries didn't change the laws. Apple saw a business change that would hit them in their production, so something that started 'national' [for simplicity sake let's say the EU is a nation] made a big splash. You might be thinking of something else and not a 'simple' regulation.
  • Recent Achievements

    • Reacting Well
      pelaird earned a badge
      Reacting Well
    • Mentor
      The Werewolf went up a rank
      Mentor
    • First Post
      Myriachan earned a badge
      First Post
    • Week One Done
      DrRonSr earned a badge
      Week One Done
    • Week One Done
      Sharon dixon earned a badge
      Week One Done
  • Popular Contributors

    1. 1
      +primortal
      603
    2. 2
      ATLien_0
      214
    3. 3
      +FloatingFatMan
      169
    4. 4
      Michael Scrip
      151
    5. 5
      Som
      151
  • Tell a friend

    Love Neowin? Tell a friend!