Recommended Posts

Your wording is off, for starters where is your router in this setup?  Modem is not a router, if this device connected to the cloud is a modem/router combo then its called a "gateway"

 

And would not use the term route for a connection from one switch to another switch.  Unless your talking a layer 3 switch that is doing routing between segments?  And really you have fiber line that connects to your switch?  Or does that connect to your gateway that changes it to ethernet?

 

You have that AP between your modem and switch - is that really your router?  And you have an actual "modem" ?  Where does it change from public IP to private in this drawing?

Link to comment
https://www.neowin.net/forum/topic/1209265-network-setup/#findComment-596358905
Share on other sites

That's my point wording is wrong ;)

 

AP is not a "router"  So that should be labled "wireless router".

 

And there is not need of mention of "route" to second switch.. Its a given that your switches are connected, if your not "routing" on layer 3 switches then don't use that term.

Link to comment
https://www.neowin.net/forum/topic/1209265-network-setup/#findComment-596359069
Share on other sites

Rework the layout of the cables so they don't cross over each other.

 

I take it your fishing for network changes - like what you have 1 network segment and couple of switches..  What do you think you could change there?

Link to comment
https://www.neowin.net/forum/topic/1209265-network-setup/#findComment-596359431
Share on other sites

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • If you look at all RAID implementations that exist, you're going to find exceptions. However, all the modern consumer varieties tend to have some things in common (by default). I'll stick to describing those. When you add a disk to a RAID array, metadata is stored at the end of the disk. It records the array the disk is part of, which other disks are in the array, etc. This is called the RAID superblock. If you create a RAID 1 array, your operating system will see them all as a single disk that is very slightly smaller than a single disk (due to the superblock). Everything you write to the RAID disk gets written identically to each of its member disks by the storage controller. Technically, disks are read/written in blocks (each block is multiple sectors in size), but this is all transparent to the user. Every file you create or change or delete is created/changed/deleted on every member disk simultaneously. This is true whether you have 2 disks in the array or more than 2.  If one disk completely fails, you can still operate just fine off the remaining disk(s) (but see the caution below). If you remove one disk and attach it to another PC, it should work fine. The partition information and everything is all at the front of the disk, just as expected. The superblock will just appear as some extra junk at the very end of the disk, outside any partition. In some scenarios, where it is recognized as a RAID member disk from another PC, there might be an extra step before it will let you use it, but it's all very doable. Caution:  Blocks are read from the disks in a staggered fashion. For example, with 2 disks, all the odd blocks are read from one disk and all the even blocks are read from the other. By working together like this, read speeds can be practically doubled. But this comes with a huge drawback. If a disk doesn't fail completely, but instead develops bad sectors, you may not realize it. The bad sectors may happen to be in blocks that are never read on that disk. In some cases, people have had bad sectors develop on one disk, then had the other disk fail, and only then realized that the remaining disk has bad sectors and corrupt data. Every backup method has its pros and cons. Never trust just RAID, or just an external HDD, or just the cloud. Use multiple methods to backup important data.
    • Evidence that it affects "most" people negatively? Based on what? The fact that their are millions of users in fact show me the opposite, that "most" are quite happy.
  • Recent Achievements

    • Conversation Starter
      Kavin25 earned a badge
      Conversation Starter
    • One Month Later
      Leonard grant earned a badge
      One Month Later
    • Week One Done
      pcdoctorsnet earned a badge
      Week One Done
    • Rising Star
      Phillip0web went up a rank
      Rising Star
    • One Month Later
      Epaminombas earned a badge
      One Month Later
  • Popular Contributors

    1. 1
      +primortal
      537
    2. 2
      ATLien_0
      205
    3. 3
      +FloatingFatMan
      167
    4. 4
      Michael Scrip
      151
    5. 5
      Som
      127
  • Tell a friend

    Love Neowin? Tell a friend!