Recommended Posts

Introduction

With the way WiFi has advanced over the last few years you'd think that wireless routers would pack enough power to punch strong signals through most household walls and floors but sadly this isn't the case and the only way to get stable wireless to the far reaches of a home is to extend the range or install access points.
The wireless option is what most will no doubt wish for as it's most convenient. Just how reliable are these devices though? Let's find out.

Asus have been kind enough to send me both the RP-N53 and RP-N14 wireless range extenders to review. The N53 boasts N600 connectivity to take advantage of the 5GHz (as well as 2.4GHz) band while the N14 is the no standard 2.4GHz version.

 

A26A1098.jpg

A26A1125.jpg

 

A26A1099.jpg

A26A1126.jpg

 

I've been testing these over the last couple of weeks after initial teething problems getting them connected to my Netgear WNDR3700 v1 router. I realised the problem was two fold.

 

 

Product exploration & installation

In the first instance my understanding of how the extenders are set up initially was muddied by the installation guide Asus provide on the respective product pages.Patience is the key here! The manual says to wait a minute when first powering it on after which the System LED will blink twice and become stable. It takes a bit longer and I didn't notice a double blink on either N14 or N53.

Secondly I had to drop a few channels on my router's Wireless config as I was using the upper most ranges for both bands which resulted in the extenders either not connecting at all or having a weak connection.

 

Other than these issues the rest of the setup and use was pleasant and almost everything just seemed to work as expected.

 

A26A1119.jpg

 

The units themselves look like clones of each other. Without getting your eyeball right up close you won't be able to tell the difference between the two as they have the same ports and same design. The N53 has an additional LED array for the 5GHz band of course so once powered up and connected that's one way to tell which is which I suppose.

 

A26A1122.jpg

 

Buttons wise we don't have much. There's a power on/off switch and a connection button labelled WPS. The little hole above the power switch is a reset button that you hold to factory reset the device. On the opposite side there's just a headphones connector and an Ethernet cable for using these extenders as Wireless access points instead should that be your requirement. This review will focus on their primary task, extending the wireless range.

 

A26A2001.jpg

 

I found the nightlight feature amusing, both extenders have a touch panel just above the LED area which turns on and off the back facing white LED. It's not very bright and there's no option in the GUI to adjust the brightness either. It's just on or off. You can however configure other things for the touch panel as can be seen in the below screenshot:

RP-N53_GUI_2.jpg

 

 

You'll notice an Audio tab, this has some predefined online radio stations and you have the option to add custom ones too.

I could not get these to work. Click play and nothing happens, no music via the headphones socket on the extender or from my computer. It's not a feature I would ever wish to use though - That's what Spotify is for.

 

Configuration

Once you've paired up the extenders to your router using the WPS button (you can also pair it up even if you don't have a WPS button on your router by connecting to the default SSID out of the both via a smartphone or laptop) there's very little else that needs changing. Most people won't even need to go into the extender's GUI pages in fact but should you wish to tinker then Asus provide a very easy to use interface to do just that:

RP-N53_GUI.jpg

 

What's cool about these extenders is that once you're paired up the extenders will pull down the security details for your home wireless network and extend it with a new SSID which is the same as your normal WiFi but with the extension "_RPT" or "_RPT5G" when using the 5GHz band. As you can see from the above screenshot you could later go in and rename this to make more sense, perhaps "yourssidhere_upstairs" - The choice is all yours :)

 

Speaking of 5GHz, I found something of an oddity here. I don't have access to any Asus routers to confirm if it is only fully functional with  their own brand routers but the N53 would not see or connect to my 5GHz band being broadcast by my Netgear WNDR3700. The band certainly works as every other Wireless-N capable device I have can connect to it.

 

In the below screenshot you can see what my Galaxy Note 3 lists for the WiFi networks. Notice that the 2.4GHz band is extended fine. The N53 has then extended the 2.4GHz band again but it's rebroadcasting it as a 5GHz band.

RP-N53_WiFiList.jpg

 

I then logged into the RP-N53 GUI and checked that it definitely could not see the 5GHz SSID, indeed that was the case...

RP-N53_WiFiList_2.jpg

 

The curious thing is that if this is a limitation on the N53 itself then you have to ask why. Why limit the extender to only connect to a 2.4GHz band which connects at 65Mbps and then extend that as a 5GHz band? That defeats the objective of the full capability of the band and the speed will only be as fast as the weakest link, this being 2.4GHz at 65Mbps.

 

As I say, I don't have access to an Asus router to test this properly so am only going by what I've found from connecting with my non Asus router.

 

 

Performance

With all that said, extended 2.4GHz works as expected. I gave home to the extenders in the upsatirs landing at a distance which was roughly the same as the distance as from the PC room to downstairs where my router is. I felt this would offer adequate range and fairness.

 

I did 3 tests:

 

1: Signal quality diagnostic.
2: Speedtest to the same Bournemouth server. The best average of a few runs was recorded. My internet line is 152Mbps down for reference.
3: LAN test. Storing a large file on to a mobile device over the network.

 

Netgear WNDR3700 (my router, to set a baseline to compare against):

Signal:

WNDR_2.4GHz_signal.jpg

 

Speedtest:

WNDR_2.4GHz_speedtest.jpg

 

LAN:

WNDR_2.4GHz_LAN.jpg

 

 

Asus RP-N53:

Signal:

RP-N53_2.4GHz_signal.jpg

 

Speedtest:

RP-N53_2.4GHz_speedtest.jpg

 

LAN:

RP-N53_2.4GHz_LAN.jpg

 

Asus RP-N14:

Signal:

RP-N14_2.4GHz_signal.jpg

 

Speedtest:

RP-N14_2.4GHz_speedtest.jpg

 

LAN:

RP-N14_2.4GHz_LAN.jpg

 

 

Conclusion

As you can see from the results, the RP-N53 achieved the better signal strength vs the N14 but both were slower at 2.4GHz than the direct Wireless connection to my router. The LAN transfer speed shows it's half the performance in sustained transfers. I suppose this makes sense. factoring in distance and overheads you'd never expect the same kind of performance you get from connecting direct to your router instead of going via an extender. Cut the middle man out and you get better performance.

 

So it's not the kind of device you want if you're looking to stream HD movies or large files over your home network between devices then but for everyday web access and multimedia it should be just fine as evidenced by the speedtest results. Notice that the latency doesn't change a great deal either so casual gamers won't be suffering either.

 

At time of writing The RP-N14 is ?34 on Google Shopping and the RP-N53 is ?58. I think these prices are reasonable for what you're getting. An easy to use, easy to configure range extender that doubles up as an access point and has a night light even if it is a bit gimmicky (why isn't it facing outward anyway!).

 

While local network performance didn't quite live up to the demands of a modern household that might be sharing large volumes of data between networked devices, both these extenders are capable of keep users satisfied as far as internet usage goes and are ideal for installing in places around the home where the main Wireless airwaves can't quite reach and need a little boost.

 

Once again, thank you for taking the time to read this review and hopefully the info in it will be of use to someone out there and thank you to Asus for sending out these extenders for review.

  • Like 2

It would be interesting to try out other extenders to see differences between brands too. I imagine the Asus one is one of the easier ones to configure though given how simple and nice the GUI is :)

It would be interesting to try out other extenders to see differences between brands too. I imagine the Asus one is one of the easier ones to configure though given how simple and nice the GUI is :)

ASUS seems to be bringing out some of the best kit overall (going by smallnetbuilder.)

  • 3 months later...

Nice review. Damn, how big are people's houses that a wireless router can't reach? I have a wireless N setup at my parents house that used to cover 3,200 sq. ft of house, and the deck/backyard also. It worked beautifully, got great coverage throughout. 

  • 5 weeks later...

I am considering an extender as well. My house isn't big, but if I go around the corner of the hallway the signal drops to almost nothing. I guess the size of the house doesn't really matter, what does is the material your walls are made out of. Probably the thinner and lighter they are, the easier the WiFi signal will get through. 

This topic is now closed to further replies.
  • Posts

    • Display Driver Uninstaller (DDU) 18.1.5.5 by Razvan Serea Display Driver Uninstaller (DDU) is a utility for completely removing AMD/NVIDIA/INTEL graphics drivers and related packages from your system, attempting to eliminate all leftovers (including registry entries, folders and files, driver store). Though AMD/NVIDIA/INTEL drivers can usually be removed via the Windows Control Panel, this uninstaller tool was created for situations where standard uninstall fails, or when you need to fully remove NVIDIA or ATI graphics card drivers. After using this driver cleaner, your system will behave as though it’s the first time you’re installing a new driver—similar to a fresh Windows installation. As with all such tools, we recommend creating a restore point beforehand, allowing you to undo changes if issues arise. If you're having trouble installing an older or newer driver, try it—there are reports that it resolves such problems. Recommended usage: The tool can be used in Normal mode but for absolute stability when using DDU, Safemode is always the best. Make a backup or a system restore (but it should normally be pretty safe). It is best to exclude the DDU folder completely from any security software to avoid issues. You do NOT need to uninstall the driver prior using DDU. Requirements: .NET Framework 4.8 Compatible with Windows 7, 8, 8.1, 10, and 11 (32-bit or 64-bit) Note: Using on Insider Preview builds is at your own risk. Display Driver Uninstaller (DDU) 18.1.5.5 changelog: Added 'Reset to recommended' button for the Options. General fixes and improvements. Download: Display Driver Uninstaller (DDU) 18.1.5.5 | 1.7 MB (Freeware) Download: DDU Portable | 1.2 MB Links: Display Driver Uninstaller Home Page | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • WACUP 1.99.51.24568 Preview by Razvan Serea WACUP (WinAmp Community Update Project) is a modern, enhanced version of the classic Winamp music player, designed for better stability, performance, and compatibility. Built for Windows, WACUP retains the familiar Winamp interface while adding 64-bit support, bug fixes, and new features like improved audio format support, customizable skins, and optimized playlist management. Unlike bloated alternatives, WACUP focuses on lightweight performance and regular updates, making it the best choice for fans of the classic Winamp experience. Basically, if you miss the good old days of Winamp and want a modern upgrade that doesn’t mess things up, WACUP is for you! WACUP key features: Classic Winamp Feel – Keeps the familiar interface and functionality. Bug Fixes & Stability – Fixes old Winamp issues and improves performance. 64-Bit Support – Works better on modern systems. More Formats & Plugins – Supports additional audio formats and third-party plugins. Customizable UI – Skins and tweaks for a personalized look. Better Library Management – Improved playlists, media organization, and search. No Bloat – Focuses on performance without unnecessary extras. Regular Updates – Community-driven development with new features and fixes. WACUP 1.99.51.24568 Preview changelog: Fixed a deadlock seen from the recent crash reports when doing some of the drag + drop actions within the media library window Fixed a loading crash seen related to a problem with some of the artwork cache image files being restored which should now be better handled allowing for the bad image to be removed without it failing Fixed a deadlock seen from the recent crash reports when the internal metadata cache clearing is triggered which could block the main ui thread for too long with this now being moved to a background thread Fixed some performance issues with some of the methods related to determining artwork support which mainly affected the local library import / refresh (this is still slower for some compared to other players because there's more data & artwork aspects being checked for which means doing more processing on a single file despite the best of attempts to reduce duplicate / heavy processing where possible) Fixed a crash with the JTFE based missing files hotkey which no one seems to have used for an age for this to appear (maybe it's time to seriously consider stripping out features that aren't being used) Fixed how some of the file types which use extra information to reference their sub-songs is handled which was preventing some from being correctly resolved back to their base file (noticed fixing above) Fixed an issue with the handling of files with underscores in their filepath which wasn't being correctly handled causing some of the filename to be lost when shown as the title if title reading is delayed Fixed a few things that might be behind NotSoDirect not being stable for some setups though am still not certain that the changes done for this are going to fully resolve the problem from the crash reports Fixed the OS toast handling when there's no prior shortcut in the OS start menu to now create the shortcut (needed to allow the yes/no buttons for the new build / post-release toast) to be done as a hidden one so it's less likely to cause annoyance for those not wanting to see it whilst still allowing this less than ideal OS api implementation requirement to be met to avoid toasts without the needed buttons Fixed a regression when moving from taglib1 to taglib2 which broke some of the handling in place to allow for external programs to still access files when wacup has a held open cached instance of the file Everything else Updated cppwinrt (gen_win10shell.dll) to 3.0.260520.1 (26 May 2026) Updated libcurl (libcurl.dll) to 8.2.1 (24 Jun 2026) Updated Monkey's Audio (in_ape.dll) to 13.15 (28 Jun 2026) Updated mpg123 (mpg123.dll) to 1.33.6 (6 Jun 2026) Updated OpenSSL (libcurl.dll) to 3.5.7 (9 Jun 2026) Updated pugixml to 1.16 (16 Jun 2026) Updated taglib (tag2.dll) to 2.3.0 (11 May 2026) Updated vgmstream (in_vgmstream.dll) to the latest Git commit from 28 Jun 2026 Download: WACUP 64-bit | 9.6 MB (Freeware) Download: WACUP 32-bit View: WACUP Website | Screenshots Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • "over a thousand engineering hours" and started selling it but could not take a couple of minuets to send an AI email to ask permission. What an expensive lesson.
    • just tested it yesterday, a simple page with autoloading ADS takes 60mb....just 1 page for 60 megabytes.   poor people with a limited internet never will visit neolose
    • Tor Browser 15.0.17 by Razvan Serea Protect your privacy. Defend yourself against network surveillance and traffic analysis. Tor is a network of virtual tunnels that allows people and groups to improve their privacy and security on the Internet. The Tor software protects you by bouncing your communications around a distributed network of relays run by volunteers all around the world: it prevents somebody from watching your Internet connection and learning what sites you visit, it prevents the sites you visit from learning your physical location, and it lets you access sites which are blocked. The Tor Browser Bundle lets you use Tor on Windows, Mac OS X, or Linux without needing to install any software. It can run off a USB flash drive, comes with a pre-configured web browser to protect your anonymity, and is self-contained. Tor Browser 15.0.17 changelog: All Platforms Updated Tor to 0.4.9.11 Updated NoScript to 13.6.25.1984 Build System / All Platforms Bug tor-browser-build#41821: Update gpg subkeys for boklm Bug tor-browser-build#41827: Update morgan's keychain with renewed key Download: Tor Browser (64-bit) | Tor Browser (32-bit) | 109.0 MB (Open Source) View: Tor Browser Website | Other Operating Systems Get alerted to all of our Software updates on Twitter at @NeowinSoftware
  • Recent Achievements

    • Reacting Well
      Wakeen1966 earned a badge
      Reacting Well
    • Rookie
      Almohandis went up a rank
      Rookie
    • Apprentice
      jahara21 went up a rank
      Apprentice
    • Reacting Well
      NovaEdgeX earned a badge
      Reacting Well
    • Week One Done
      NovaEdgeX earned a badge
      Week One Done
  • Popular Contributors

    1. 1
      +primortal
      530
    2. 2
      +Edouard
      266
    3. 3
      PsYcHoKiLLa
      148
    4. 4
      Steven P.
      99
    5. 5
      macoman
      55
  • Tell a friend

    Love Neowin? Tell a friend!