Computer won't boot after new CPU cooler and gets into reboot


Recommended Posts

I just installed a new CPU cooler. Everything is attached again to my mobo (I think ok - haha)

When booting my PC gets into a loop and I cannot log into Windows. A clicking sound is made and than boots again.

The BIOS can be reached. I already have set everything to its default values, without success.

The CPU is recognized as well as the SSD that boots. The Windows 8.1 bootup screen is displayed and than a loop.

Afterwards the Repair mode is coming up.

What can be the issue for this reboot loop? Have I overlooked something or maybe not connected the right way?

I think it's the PSU dying or already dead... (the PSU is 5 years old and almost constantly on)

damn!

 

The sound is a clicking sound, and my computer gets in a constant reboot.

 

Question is, since I'm already thinking of getting a new PC, will I just get a new PSU or now a complete new PC, mobo/CPU and everything...?!

Don't expect a reply in here in 8 hours.

 

PSU's can often overload components, therefore creating electric whines.

 

Get a new PSU. You can use it for your next build.

I installed the new 860W Corsair PSU.

However, problem is still there.

 

What I see:

- the BIOS is displayed

- the Windows 8 bootcircle

- 2 clicks

- Windows bootcircle continues spinning

- that the reboot

 

After that a screen is displayed "Preparing Automatic Repair" which cannot repair anything....

 

Help! What might be the issue here?

It's a cold boot after a day or so not used. Overheating can still happen than?

Before replacing my CPU cooler Windows did boot normally, although the clicks were still there (that's why I initially replaced only the CPU cooler)

I'd check all your connectors in case something got knocked loose in the process (fans, usb, SATA, whatever,) reset the BIOS, and if still no go reseat the proc and HSF (possible too much pressure, possible too much goo and it got onto the components)

 

920s are twitchy beasts.  I gave up on mine.

 

(If the PSU definitely isn't the problem I'd find a way to check the SSDs too.)

have you tried putting the original cpu cooler back on to see if it boots?

 

with your new cpu cooler did it come pre-applied with thermal paste or did you apply it when you switched out the coolers?

Disconnect the power connection for the new CPU Cooler (Fan?) to the motherboard and then try boot the system.

 

If it fixes the issue its the CPU Cooler.

 

p.s Just disconnect it for testing, don't keep using the computer as the CPU will probably overheat without the cooler with prolonged use.

I had a cooling fan that was plugging into a laptop causing the light to just blink but not turn on. After unplugging the cooling fan the laptop turned on. So maybe the fan is shorting it out or something.

Have you tried booting into safe mode to rule out windows being the problem?

http://www.howtogeek.com/107511/how-to-boot-into-safe-mode-on-windows-8-the-easy-way/

 

Where are these 'Clicks' coming from? hardware inside? speakers??

 

 

Also, does your graphics card have a separate power feed and is it plugged in correctly?

 

 

Whatever you do, do NOT try and turn on the PC without a heatsink attached.

 

 

Resetting the bios can sometimes also cause more problems. i.e it might disable SATA AHCI and revert to old IDE mode which will make windows fail to load if it is expecting it to be AHCI compatible.

  On 13/08/2014 at 22:12, kiddingguy said:

I just installed a new CPU cooler. Everything is attached again to my mobo (I think ok - haha)

When booting my PC gets into a loop and I cannot log into Windows. A clicking sound is made and than boots again.

What can be the issue for this reboot loop? Have I overlooked something or maybe not connected the right way?

I would triple check the hard drive connections.

 

Both the power connection and data cable -- including the cable to the motherboard.

 

You might swap out the data cable too, in case it is bad.

  On 15/08/2014 at 15:14, f1ux said:

Resetting the bios can sometimes also cause more problems. i.e it might disable SATA AHCI and revert to old IDE mode which will make windows fail to load if it is expecting it to be AHCI compatible.

True, though I'd expect people modding their comp to be aware of that and change it to the right setting, since they had to when they set up the comp in the first place.

  On 15/08/2014 at 14:55, GotBored said:
GotBored, on 15 Aug 2014 - 16:55, said:

Disconnect the power connection for the new CPU Cooler (Fan?) to the motherboard and then try boot the system.

 

If it fixes the issue its the CPU Cooler.

 

p.s Just disconnect it for testing, don't keep using the computer as the CPU will probably overheat without the cooler with prolonged use.

 

I tried this, but the BIOS error I get is that the CPU fan must be connected. No boot at all.

 

The old fan isn't working any more, so that won't be an option.

Tomorrow I will place the CPU once again and see if it's working. In the BIOS it's recognized. I applied the paste myself.

Keep you all posted.

I think it might have something to do with AHCI and IDE and some BIOS setting.

When quickly changing AHCI the clicks were gone, but an error message popped up that My computer/Windows has ran into trouble.

 

I will dig in this further tomorrow.

 

Thanks so far for the feedback!

If you're booting to windows it's not your PSU. The motherboard checks for sufficient power before even attempting to boot. If you have insufficient power, you might just hear fans running. An improperly mounted or insufficient heat sink would cause a thermal shutdown, not a reboot loop into Windows. If the CPU was damaged you wouldn't POST or get past the BIOS. I suspect you're hitting a blue screen in regards to the disk controller and the machine is configured to reboot on stop errors, hence the loop. Can you access the Windows boot options before it loads windows? Can you get into safe mode?

I've seen this issue recently, and it turned out that one of the RAM sticks was loose.  It occurred after cleaning dust out the case, so changing the orientation knocked it loose.

 

Not sure if it's the same issue you're seeing, but it's quick and easy to check.

  On 15/08/2014 at 15:50, kiddingguy said:

I tried this, but the BIOS error I get is that the CPU fan must be connected. No boot at all.

 

The old fan isn't working any more, so that won't be an option.

Tomorrow I will place the CPU once again and see if it's working. In the BIOS it's recognized. I applied the paste myself.

Keep you all posted.

 

That's good, one of the fault conditions which will cause the system to boot cycle (or shutdown) is if the CPU Fan is not detected. Your BIOS gives you a warning message when this happens so its safe to say the fan is being recognized and doesn't have an internal short or open cct which could be causing the failures. Make sure no cables are getting stuck in the fan during operation and that it spins freely and you can rule out the cpu fan.

 

  On 15/08/2014 at 16:09, kiddingguy said:

I think it might have something to do with AHCI and IDE and some BIOS setting.

When quickly changing AHCI the clicks were gone, but an error message popped up that My computer/Windows has ran into trouble.

 

I will dig in this further tomorrow.

 

Thanks so far for the feedback!

 

Does it still try to do a boot cycle or is it staying in Windows now with an error message?

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • I know with my isp they will only support certain models. You might want to check with them,
    • Steam Summer Sale 2025 is here offering weeks of massive discounts for PC gamers by Pulasthi Ariyasinghe It is time to jump into another Steam Summer Sale. The 2025 edition of the yearly massive sale at the biggest PC gaming store on the market has just kicked off, and it is touting thousands of discounts for everything from the oldest classics to the newest releases and everything in between. The Steam servers predictably wobbled for a while at the launch of the sale, but things finally seem to be calming down enough to browse the latest sales. The front page is the place to be for anyone looking for recommendations, with it putting the spotlight on fresh games every day. However, keep in mind that the discounts themselves will not be changing and will remain static throughout the sale. Some recent blockbusters like Metaphor: ReFantazio, Monster Hunter Wilds, Sid Meier's Civilization VII, Black Myth: Wukong, Call of Duty: Black Ops 6, Clair Obscur: Expedition 33, Warhammer 40,000: Space Marine 2, Indiana Jones and the Great Circle, Blue Prince, Kingdom Come: Deliverance II, and much more are currently discounted. Valve has also brought back the special "Deep Discounts" section, letting Steam users find the most deeply discounted games quickly straight from the front page. The page has a selection of "all-time greats" with 85% to 95% cuts to their standard prices. This time, it includes titles like Black Mesa, Little Nightmares II, Kerbal Space Program, Steins Gate, Furi, Crash Bandicoot N. Sane Trilogy, Star Wars Battlefront II, Robocop Rogue City, and much more for just a few dollars each. As for the duration, the Steam Summer Sale of 2025 will be open for business until July 10, giving all of you two whole weeks to try and keep your wallets closed tight. As always, be sure to read our Weekend PC Game Deals special this coming Saturday to check out the biggest highlights from the sale. If you miss this store-wide promotion, Valve's next major sale will land this September as part of a new time slot for the Steam Autumn Sale. Head over here to see the complete 2025 sales roadmap for the platform.
    • Great way to get an entire physical model of the products (i.e. end users) and better market them...definitely not something I'd want on ANY of my personal devices, but can be useful in retail shops for sure.
    • Hi all. ISP pushing me from 800Mbps to  1200Mbps, however, I want to buy my own modem. Theirs have been a bit wonky, would rather just handle it myself. Data capped at 1.2TB, haven't gone over yet (although pretty close at times), paying $15 rental, some have suggested a DIY solution. Anyway, I'm in need of a few upgrades and need some suggestions. My onboard LAN is capped at 1Gbit (I219-v and a Killer E2500), choose your poison? Anyway, an add-on NIC might be in order, not sure what to go with. Then there's the modem and router. A lot of these modems are very close in price, some supporting 2.3 - 2.5Gbit, others a flat 1Gbit that wouldn't let me touch my 1200Mbit that I'm paying. Boils down to a Netgear CM3000 (for below cost due to built up rewards) or Motorola B12. Then of course, there's my router. I bought a Nighthawk X10 a while ago for $10 at thrift, before this whole upgrade thing came up. Its ports are capped at 1Gbit, but it DOES have a 10Gbit SFP+ port. I could possibly get a NIC that has sfp+ port, or a switch that has 2.5Gbit ports. I'm the only wired PC in the house, everything else is wifi, no foreseeable new wired connections in the far off future. Or, I could get an RS100 router that would let me use my 1200Mbit connection. I've been subscribed for about 6 years, so have paid about $1080 in rental since then. It's too bad I didn't DIY since the beginning, it would have been paid of long ago -_- better late than never I guess. What's your thought on this?
  • Recent Achievements

    • First Post
      TheRingmaster earned a badge
      First Post
    • Conversation Starter
      Kavin25 earned a badge
      Conversation Starter
    • One Month Later
      Leonard grant earned a badge
      One Month Later
    • Week One Done
      pcdoctorsnet earned a badge
      Week One Done
    • Rising Star
      Phillip0web went up a rank
      Rising Star
  • Popular Contributors

    1. 1
      +primortal
      552
    2. 2
      ATLien_0
      205
    3. 3
      +FloatingFatMan
      180
    4. 4
      Michael Scrip
      147
    5. 5
      Som
      119
  • Tell a friend

    Love Neowin? Tell a friend!