Computer won't boot after new CPU cooler and gets into reboot


Recommended Posts

I just installed a new CPU cooler. Everything is attached again to my mobo (I think ok - haha)

When booting my PC gets into a loop and I cannot log into Windows. A clicking sound is made and than boots again.

The BIOS can be reached. I already have set everything to its default values, without success.

The CPU is recognized as well as the SSD that boots. The Windows 8.1 bootup screen is displayed and than a loop.

Afterwards the Repair mode is coming up.

What can be the issue for this reboot loop? Have I overlooked something or maybe not connected the right way?

I think it's the PSU dying or already dead... (the PSU is 5 years old and almost constantly on)

damn!

 

The sound is a clicking sound, and my computer gets in a constant reboot.

 

Question is, since I'm already thinking of getting a new PC, will I just get a new PSU or now a complete new PC, mobo/CPU and everything...?!

Don't expect a reply in here in 8 hours.

 

PSU's can often overload components, therefore creating electric whines.

 

Get a new PSU. You can use it for your next build.

I installed the new 860W Corsair PSU.

However, problem is still there.

 

What I see:

- the BIOS is displayed

- the Windows 8 bootcircle

- 2 clicks

- Windows bootcircle continues spinning

- that the reboot

 

After that a screen is displayed "Preparing Automatic Repair" which cannot repair anything....

 

Help! What might be the issue here?

It's a cold boot after a day or so not used. Overheating can still happen than?

Before replacing my CPU cooler Windows did boot normally, although the clicks were still there (that's why I initially replaced only the CPU cooler)

I'd check all your connectors in case something got knocked loose in the process (fans, usb, SATA, whatever,) reset the BIOS, and if still no go reseat the proc and HSF (possible too much pressure, possible too much goo and it got onto the components)

 

920s are twitchy beasts.  I gave up on mine.

 

(If the PSU definitely isn't the problem I'd find a way to check the SSDs too.)

have you tried putting the original cpu cooler back on to see if it boots?

 

with your new cpu cooler did it come pre-applied with thermal paste or did you apply it when you switched out the coolers?

Disconnect the power connection for the new CPU Cooler (Fan?) to the motherboard and then try boot the system.

 

If it fixes the issue its the CPU Cooler.

 

p.s Just disconnect it for testing, don't keep using the computer as the CPU will probably overheat without the cooler with prolonged use.

I had a cooling fan that was plugging into a laptop causing the light to just blink but not turn on. After unplugging the cooling fan the laptop turned on. So maybe the fan is shorting it out or something.

Have you tried booting into safe mode to rule out windows being the problem?

http://www.howtogeek.com/107511/how-to-boot-into-safe-mode-on-windows-8-the-easy-way/

 

Where are these 'Clicks' coming from? hardware inside? speakers??

 

 

Also, does your graphics card have a separate power feed and is it plugged in correctly?

 

 

Whatever you do, do NOT try and turn on the PC without a heatsink attached.

 

 

Resetting the bios can sometimes also cause more problems. i.e it might disable SATA AHCI and revert to old IDE mode which will make windows fail to load if it is expecting it to be AHCI compatible.

  On 13/08/2014 at 22:12, kiddingguy said:

I just installed a new CPU cooler. Everything is attached again to my mobo (I think ok - haha)

When booting my PC gets into a loop and I cannot log into Windows. A clicking sound is made and than boots again.

What can be the issue for this reboot loop? Have I overlooked something or maybe not connected the right way?

I would triple check the hard drive connections.

 

Both the power connection and data cable -- including the cable to the motherboard.

 

You might swap out the data cable too, in case it is bad.

  On 15/08/2014 at 15:14, f1ux said:

Resetting the bios can sometimes also cause more problems. i.e it might disable SATA AHCI and revert to old IDE mode which will make windows fail to load if it is expecting it to be AHCI compatible.

True, though I'd expect people modding their comp to be aware of that and change it to the right setting, since they had to when they set up the comp in the first place.

  On 15/08/2014 at 14:55, GotBored said:
GotBored, on 15 Aug 2014 - 16:55, said:

Disconnect the power connection for the new CPU Cooler (Fan?) to the motherboard and then try boot the system.

 

If it fixes the issue its the CPU Cooler.

 

p.s Just disconnect it for testing, don't keep using the computer as the CPU will probably overheat without the cooler with prolonged use.

 

I tried this, but the BIOS error I get is that the CPU fan must be connected. No boot at all.

 

The old fan isn't working any more, so that won't be an option.

Tomorrow I will place the CPU once again and see if it's working. In the BIOS it's recognized. I applied the paste myself.

Keep you all posted.

I think it might have something to do with AHCI and IDE and some BIOS setting.

When quickly changing AHCI the clicks were gone, but an error message popped up that My computer/Windows has ran into trouble.

 

I will dig in this further tomorrow.

 

Thanks so far for the feedback!

If you're booting to windows it's not your PSU. The motherboard checks for sufficient power before even attempting to boot. If you have insufficient power, you might just hear fans running. An improperly mounted or insufficient heat sink would cause a thermal shutdown, not a reboot loop into Windows. If the CPU was damaged you wouldn't POST or get past the BIOS. I suspect you're hitting a blue screen in regards to the disk controller and the machine is configured to reboot on stop errors, hence the loop. Can you access the Windows boot options before it loads windows? Can you get into safe mode?

I've seen this issue recently, and it turned out that one of the RAM sticks was loose.  It occurred after cleaning dust out the case, so changing the orientation knocked it loose.

 

Not sure if it's the same issue you're seeing, but it's quick and easy to check.

  On 15/08/2014 at 15:50, kiddingguy said:

I tried this, but the BIOS error I get is that the CPU fan must be connected. No boot at all.

 

The old fan isn't working any more, so that won't be an option.

Tomorrow I will place the CPU once again and see if it's working. In the BIOS it's recognized. I applied the paste myself.

Keep you all posted.

 

That's good, one of the fault conditions which will cause the system to boot cycle (or shutdown) is if the CPU Fan is not detected. Your BIOS gives you a warning message when this happens so its safe to say the fan is being recognized and doesn't have an internal short or open cct which could be causing the failures. Make sure no cables are getting stuck in the fan during operation and that it spins freely and you can rule out the cpu fan.

 

  On 15/08/2014 at 16:09, kiddingguy said:

I think it might have something to do with AHCI and IDE and some BIOS setting.

When quickly changing AHCI the clicks were gone, but an error message popped up that My computer/Windows has ran into trouble.

 

I will dig in this further tomorrow.

 

Thanks so far for the feedback!

 

Does it still try to do a boot cycle or is it staying in Windows now with an error message?

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • I see the Winblows 11 BETA testing continues. This is just Windows 10 all over again. Oh well, everything is still smooth sailing over here on Windows 10 21H2 LTSC. You unpaid sheep BETA testers be sure to let us know when you get done BETA testing Winblows 11 for the rest of us. 🤣
    • What do you expect? Windows 11 is still in BETA. This is Windows 10 all over again. M$ doesn't hire people to do BETA testing anymore. They just let all the dumb sheep with FOMO do all the BETA testing for them. It's the same dumb sheep who use self-checkout at the store and do someone else's job for FREE! All while the worker who's getting paid just stands there and watches them. 🤣 🤡
    • Pet peeve: Microsoft using scaling options to get around the fact they removed font size settings, as if that's somehow acceptable to do. Thankfully third party apps still can adjust font sizes just fine, even though it often randomly resets on OS updates. And the funny thing is that not only are the scaling options horrible crutches, but they only work in some applications. And, ironically enough, even some apps from Microsoft themselves have hardcoded tiny fonts in certain dialogs in them. Example - certain parts of MS Office apps UI.
    • Unofficial script does the most useful official Windows 11/10 repairs you want automatically by Sayan Sen IT admins and system admins, and even home users have to run various Windows diagnostic runs from time to time in order to iron out or work around system problems. Last year, Microsoft published a guidance piece about various such native Windows apps, tools and utilities they include the like of Task Manager, Registry Editor, and more. Aside from them, Windows also comes with SFC (System File Checker) and DISM (Deployment Image Servicing and Management) to scan and fix corrupt and missing system files. Besides those, various other ways to help and diagnose network issues related to DNS (Domain Name System), among others, also exists. In order to save time running these, a Reddit user has created a new tool that automates all of these into a single package. The author writes that the Batch script (.BAT file) they have developed is "basically a one-stop script that can help clean up your system, run built-in diagnostics, fix common network issues, and generate system reports." The script is based on native Windows tools like netsh, ipconfig, systeminfo, among others, and the idea behind this is essentially to save time. The tool can be of help with Windows Update repairs, among others, something we all know is pretty common, and even Microsoft's own support articles may not prove to be helpful. Here is everything the utility can do for you: Run SFC, DISM, CHKDSK from a single menu Restart network adapters with auto-detection Flush or set DNS (Google, Cloudflare, or custom) Windows Update repair (resets services + cache) Generate system reports (saved as .txt files on Desktop) Show installed drivers Clean up temp files Registry backup and restore (manual) The latest version of the utility is now available for download on GitHub. The new version fixes issues related to admin privileges. As the script requires it to be run as an admin, it now restart itself to work in admin mode even if a user forgot to run it as an administrator. To download it, head over to its GitHub page here. The utility is named Windows Maintenance Tool. As always, though, make sure to back up your PC as this is an unofficial third-party app, and it's better if you test it first in a VM. Source: Lil_Batti (Reddit)
    • Come the hell on, do we need clickbait titles? "Overwatch 2" - 11 characters "a popular multiplayer hero shooter" - 34 characters What's the purpose here - delivering news or titles for clicks? I think we all know the answer. You're straying into "Number 7 on this list will SHOCK you" territory and while it may work on some crappy sites, this is why they are crappy sites. Just tell the story! Go back and look at popular articles that made Neowin what it was. Did they have headlines of "New OS from major technology conglomerate has astonishing new feature" or is it likely to tell the story succinctly and then elaborate within the content?
  • Recent Achievements

    • One Month Later
      CoolRaoul earned a badge
      One Month Later
    • First Post
      Kurotama earned a badge
      First Post
    • Collaborator
      Carltonbar earned a badge
      Collaborator
    • Explorer
      MusicLover2112 went up a rank
      Explorer
    • Dedicated
      MadMung0 earned a badge
      Dedicated
  • Popular Contributors

    1. 1
      +primortal
      508
    2. 2
      ATLien_0
      270
    3. 3
      +FloatingFatMan
      245
    4. 4
      +Edouard
      201
    5. 5
      snowy owl
      168
  • Tell a friend

    Love Neowin? Tell a friend!