Computer won't boot after new CPU cooler and gets into reboot


Recommended Posts

I just installed a new CPU cooler. Everything is attached again to my mobo (I think ok - haha)

When booting my PC gets into a loop and I cannot log into Windows. A clicking sound is made and than boots again.

The BIOS can be reached. I already have set everything to its default values, without success.

The CPU is recognized as well as the SSD that boots. The Windows 8.1 bootup screen is displayed and than a loop.

Afterwards the Repair mode is coming up.

What can be the issue for this reboot loop? Have I overlooked something or maybe not connected the right way?

I think it's the PSU dying or already dead... (the PSU is 5 years old and almost constantly on)

damn!

 

The sound is a clicking sound, and my computer gets in a constant reboot.

 

Question is, since I'm already thinking of getting a new PC, will I just get a new PSU or now a complete new PC, mobo/CPU and everything...?!

Don't expect a reply in here in 8 hours.

 

PSU's can often overload components, therefore creating electric whines.

 

Get a new PSU. You can use it for your next build.

I installed the new 860W Corsair PSU.

However, problem is still there.

 

What I see:

- the BIOS is displayed

- the Windows 8 bootcircle

- 2 clicks

- Windows bootcircle continues spinning

- that the reboot

 

After that a screen is displayed "Preparing Automatic Repair" which cannot repair anything....

 

Help! What might be the issue here?

It's a cold boot after a day or so not used. Overheating can still happen than?

Before replacing my CPU cooler Windows did boot normally, although the clicks were still there (that's why I initially replaced only the CPU cooler)

I'd check all your connectors in case something got knocked loose in the process (fans, usb, SATA, whatever,) reset the BIOS, and if still no go reseat the proc and HSF (possible too much pressure, possible too much goo and it got onto the components)

 

920s are twitchy beasts.  I gave up on mine.

 

(If the PSU definitely isn't the problem I'd find a way to check the SSDs too.)

have you tried putting the original cpu cooler back on to see if it boots?

 

with your new cpu cooler did it come pre-applied with thermal paste or did you apply it when you switched out the coolers?

Disconnect the power connection for the new CPU Cooler (Fan?) to the motherboard and then try boot the system.

 

If it fixes the issue its the CPU Cooler.

 

p.s Just disconnect it for testing, don't keep using the computer as the CPU will probably overheat without the cooler with prolonged use.

I had a cooling fan that was plugging into a laptop causing the light to just blink but not turn on. After unplugging the cooling fan the laptop turned on. So maybe the fan is shorting it out or something.

Have you tried booting into safe mode to rule out windows being the problem?

http://www.howtogeek.com/107511/how-to-boot-into-safe-mode-on-windows-8-the-easy-way/

 

Where are these 'Clicks' coming from? hardware inside? speakers??

 

 

Also, does your graphics card have a separate power feed and is it plugged in correctly?

 

 

Whatever you do, do NOT try and turn on the PC without a heatsink attached.

 

 

Resetting the bios can sometimes also cause more problems. i.e it might disable SATA AHCI and revert to old IDE mode which will make windows fail to load if it is expecting it to be AHCI compatible.

  On 13/08/2014 at 22:12, kiddingguy said:

I just installed a new CPU cooler. Everything is attached again to my mobo (I think ok - haha)

When booting my PC gets into a loop and I cannot log into Windows. A clicking sound is made and than boots again.

What can be the issue for this reboot loop? Have I overlooked something or maybe not connected the right way?

I would triple check the hard drive connections.

 

Both the power connection and data cable -- including the cable to the motherboard.

 

You might swap out the data cable too, in case it is bad.

  On 15/08/2014 at 15:14, f1ux said:

Resetting the bios can sometimes also cause more problems. i.e it might disable SATA AHCI and revert to old IDE mode which will make windows fail to load if it is expecting it to be AHCI compatible.

True, though I'd expect people modding their comp to be aware of that and change it to the right setting, since they had to when they set up the comp in the first place.

  On 15/08/2014 at 14:55, GotBored said:
GotBored, on 15 Aug 2014 - 16:55, said:

Disconnect the power connection for the new CPU Cooler (Fan?) to the motherboard and then try boot the system.

 

If it fixes the issue its the CPU Cooler.

 

p.s Just disconnect it for testing, don't keep using the computer as the CPU will probably overheat without the cooler with prolonged use.

 

I tried this, but the BIOS error I get is that the CPU fan must be connected. No boot at all.

 

The old fan isn't working any more, so that won't be an option.

Tomorrow I will place the CPU once again and see if it's working. In the BIOS it's recognized. I applied the paste myself.

Keep you all posted.

I think it might have something to do with AHCI and IDE and some BIOS setting.

When quickly changing AHCI the clicks were gone, but an error message popped up that My computer/Windows has ran into trouble.

 

I will dig in this further tomorrow.

 

Thanks so far for the feedback!

If you're booting to windows it's not your PSU. The motherboard checks for sufficient power before even attempting to boot. If you have insufficient power, you might just hear fans running. An improperly mounted or insufficient heat sink would cause a thermal shutdown, not a reboot loop into Windows. If the CPU was damaged you wouldn't POST or get past the BIOS. I suspect you're hitting a blue screen in regards to the disk controller and the machine is configured to reboot on stop errors, hence the loop. Can you access the Windows boot options before it loads windows? Can you get into safe mode?

I've seen this issue recently, and it turned out that one of the RAM sticks was loose.  It occurred after cleaning dust out the case, so changing the orientation knocked it loose.

 

Not sure if it's the same issue you're seeing, but it's quick and easy to check.

  On 15/08/2014 at 15:50, kiddingguy said:

I tried this, but the BIOS error I get is that the CPU fan must be connected. No boot at all.

 

The old fan isn't working any more, so that won't be an option.

Tomorrow I will place the CPU once again and see if it's working. In the BIOS it's recognized. I applied the paste myself.

Keep you all posted.

 

That's good, one of the fault conditions which will cause the system to boot cycle (or shutdown) is if the CPU Fan is not detected. Your BIOS gives you a warning message when this happens so its safe to say the fan is being recognized and doesn't have an internal short or open cct which could be causing the failures. Make sure no cables are getting stuck in the fan during operation and that it spins freely and you can rule out the cpu fan.

 

  On 15/08/2014 at 16:09, kiddingguy said:

I think it might have something to do with AHCI and IDE and some BIOS setting.

When quickly changing AHCI the clicks were gone, but an error message popped up that My computer/Windows has ran into trouble.

 

I will dig in this further tomorrow.

 

Thanks so far for the feedback!

 

Does it still try to do a boot cycle or is it staying in Windows now with an error message?

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Edge for Business gets secure password deployment for organizations by Paul Hill Microsoft Edge for Business now offers organizations secure password deployments as a generally available feature, the Redmond giant said. Instead of users sharing passwords on sticky notes or via email to access certain websites or tools, admins can deploy encrypted shared passwords to specific users within their organization. When a user receives a password, it is stored in their Edge password manager and can be used to log into websites seamlessly using autofill. Microsoft has made this enterprise-grade solution available to customers at no additional cost. How it works and the user experience Administrators have to manage the feature via the Microsoft Edge management service within the Microsoft 365 admin center. From there, they can add, update, and revoke credentials for specific user groups through configuration policies. Once an admin has set it up and shared passwords with users, the users will see the passwords in their Edge password manager and can be used with autofill on corresponding websites. The passwords are tied to work profiles in Edge on managed Windows devices to limit their misuse. Further boosting security, the shared passwords cannot actually be viewed, edited, or deleted (unless the website allows), or exported from the password manager. This is a good addition for security because if an unauthorized user gains physical access to the computer, they cannot learn what the password is. Administrators reading this do need to be aware of an important caveat related to developer tools. A motivated user who wants to reveal the passwords can do so by digging into the developer tools, for this reason, you should consider restricting access to the developer tools by configuring the DeveloperToolsAvailability policy. The underlying security and encryption Microsoft’s new secure passwords feature has been built using the Information Protection SDK. The passwords are encrypted and the encryption is tied to Entra identities which lets organizations enforce them without manual key management. The decryption of the passwords takes place at runtime using the same SDK, validating the user’s identity. Availability and getting started Secure password deployment is available through the Edge management service in the Microsoft 365 admin center. Once in the admin center, you should choose an existing configuration policy or create a new one. Inside the policy, go to the Customization Settings tab and then to the Secure password deployment page. To use this feature you must have a Microsoft 365 Business Premium, E3, or E5 subscription. The feature also requires the Edge admin or Global admin role. Source: Microsoft
    • Is it though?  I built a new rig a few months ago and it was literally impossible to get one without RGB, but within 10 minutes of setting it up, I turned all that crap off.  It was REALLY distracting, and who needs additional heat INSIDE a PC? It's popular on YouTube for sure, it's neat looking and whatnot, but it's about as practical as a coffee cup with a hole in it. As for the price, a non-enthusiast would just see something priced way above what they can get from a retailer brand new...
    • RollBack Rx Pro 12.9 Build 2710971022 by Razvan Serea RollBack Rx is a robust system restore utility that enables home users and IT professionals to easily restore a PC to a time before certain events occurred. In essence, it turns your PC into a Instant Time Machine. Regardless of what happens to your PC your can quickly and easily restore your PC to a previous time. Making it easy to rescue you from any PC disaster - saving time, money and PC trouble. Windows System Restore only restores Windows system files and some program files. In addition, if Windows crashes to a point were Windows itself can not boot up (ie. BSOD*) you would not be able to access your Windows System Restore points. In contrast, the RollBack Rx technology works at the sector level of the hard drive and restores everything! - right down to the last byte of data. It sits below Windows. So even if Windows crashes, there’s a sub-console (mini OS) that boots prior to windows. This allows you to access Rollback Rx and go back to a point in time when your system was working trouble-free. Key Features Go back to any previous point in time within seconds. Go back minutes, hours, days, weeks, or even months to any previous snapshot. Does not affect computer performance, uses minimal system resources. Supports unlimited snapshots. Creates a complete system snapshot without having to restart the system. Reverse any system crash within seconds (even if Windows cannot startup). Back out of any failed program, OS updates, and botched updates. Recover from any malware or virus attack within seconds. Works with VMWare and Virtual Machines, both as a host or within the virtual machine as a client. Supports Multi-boot, Multi OS workstations. Lock snapshots to prevent deletion. Intuitive GUI based snapshot manager. Explore, browse, and retrieve files and folders from any snapshot. Drag and drop them into your active system. Roll backwards as well as forwards to any available system snapshot. Allows users to safely test any software. Fast, 100% complete uninstaller. Retrieve files from a crashed PC, even if Windows cannot boot. Access control – manage levels of multiple user and administrative privileges. Automatically schedule snapshots to be taken on a fixed schedule or upon execution of specific files (ie. setup.exe) as well as manually. 256 bit AES snapshot encryption. Prevent unauthorized data theft in case of a stolen laptop. Group Management and Enterprise Network Administration Control (FREE utility). Comes with Stealth Mode where you can hide the RollBack Rx tray icon and splash screen (seen during bootup) Change the startup hotkey for sub-console access (default is HOME). Built-in snapshot defragmenter which will optimize system resources and recover free space. Option to keep files and folders unchanged when you roll-back. Advanced setup configuration wizard for system administrators which will set deployment options and predefined RollBack Rx settings. Offers detailed program operation logging. Supports all industry-standard deployment options including silent installations and pre-installation configuration. Explore RollBack Rx Pro with a 14-day trial, fully functional on Windows 11, 10, 8, and Windows 7 SP1** (32 and 64-bit). RollBack Rx Pro 12.9 Build 2710971022 changelog: General Add PnpLockdown in shieldm.inf Fix registry exclusion problem in Windows 11 24H2 release Add detailed logging for file filter driver Add detailed logging for Windows update Add time stamp to kernel drivers Change kernel driver and Win32 IRP structure Other small bug fixes / typos reported through tech support Endpoint Manager Add client report dashboard Add sound effect when receiving a EPM message. Keep EPM message history Fix bug that oversized Windows symbol files cannot be downloaded Download: RollBack Rx Pro 12.9 | 61.0 MB (Shareware) View: RollBack Rx Home Page Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • Universal Media Server 14.12.1 by Razvan Serea Universal Media Server is a DLNA-compliant UPnP Media Server. UMS was started by SubJunk, an official developer of PMS, in order to ensure greater stability and file-compatibility. The program streams or transcodes many different media formats with little or no configuration. It is powered by MEncoder, FFmpeg, tsMuxeR, AviSynth, MediaInfo and more, which combine to offer support for a wide range of media formats. Because it is written in Java, Universal Media Server supports all major operating systems, with versions for Windows, Linux and Mac OS X. To see a comparison of popular media servers, click here. Universal Media Server 14.12.1 changelog: General Added status page to readme Fixed videos not being marked as fully played (#5373) (thanks, @Fredo1650!) Fixed adding YouTube channels from handle URLs (URLs with @ in them) Fixed handling special characters on Linux (#5100) (thanks, @LaTeteDansLesEtoiles!) Fixed directory browsing crash (#5189) (thanks, @jt-gilkeson!) Fixed FFmpeg on Linux x86_64 and arm64 (#5465) (thanks, @KanjiMonster!) Fixed logspam like "Could not hydrate device or its services from descriptor" (#5292) (thanks, MTOakey!) Fixed broken YouTube video playback Fixed web interface E2E testing on CI using outdated code because of overeager caching Fixed broken video playback when burning subtitles to H.265 via FFmpeg (#5486) Improved logging Translation updates via Crowdin Chinese (Simplified) (59%) (thanks, 無情天!) Dutch (41%) (thanks, Matthias!) Hungarian (86%) (thanks, Zoltán Rózsa!) Japanese (69%) (thanks, Yukihuru!) Download: Universal Media Server 14.12.1 | 203.0 MB (Open Source) Download: Other operating systems View: Universal Media Server Website | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • You sign your rights to reddit when you write on their platform. Free labour for them to make money. The AI companies should also take advantage of that free labour.
  • Recent Achievements

    • Week One Done
      somar86 earned a badge
      Week One Done
    • One Month Later
      somar86 earned a badge
      One Month Later
    • Apprentice
      Adrian Williams went up a rank
      Apprentice
    • Reacting Well
      BashOrgRu earned a badge
      Reacting Well
    • Collaborator
      CHUNWEI earned a badge
      Collaborator
  • Popular Contributors

    1. 1
      +primortal
      510
    2. 2
      ATLien_0
      260
    3. 3
      +Edouard
      190
    4. 4
      +FloatingFatMan
      175
    5. 5
      snowy owl
      133
  • Tell a friend

    Love Neowin? Tell a friend!