Computer won't boot after new CPU cooler and gets into reboot


Recommended Posts

I just installed a new CPU cooler. Everything is attached again to my mobo (I think ok - haha)

When booting my PC gets into a loop and I cannot log into Windows. A clicking sound is made and than boots again.

The BIOS can be reached. I already have set everything to its default values, without success.

The CPU is recognized as well as the SSD that boots. The Windows 8.1 bootup screen is displayed and than a loop.

Afterwards the Repair mode is coming up.

What can be the issue for this reboot loop? Have I overlooked something or maybe not connected the right way?

I think it's the PSU dying or already dead... (the PSU is 5 years old and almost constantly on)

damn!

 

The sound is a clicking sound, and my computer gets in a constant reboot.

 

Question is, since I'm already thinking of getting a new PC, will I just get a new PSU or now a complete new PC, mobo/CPU and everything...?!

Don't expect a reply in here in 8 hours.

 

PSU's can often overload components, therefore creating electric whines.

 

Get a new PSU. You can use it for your next build.

I installed the new 860W Corsair PSU.

However, problem is still there.

 

What I see:

- the BIOS is displayed

- the Windows 8 bootcircle

- 2 clicks

- Windows bootcircle continues spinning

- that the reboot

 

After that a screen is displayed "Preparing Automatic Repair" which cannot repair anything....

 

Help! What might be the issue here?

It's a cold boot after a day or so not used. Overheating can still happen than?

Before replacing my CPU cooler Windows did boot normally, although the clicks were still there (that's why I initially replaced only the CPU cooler)

I'd check all your connectors in case something got knocked loose in the process (fans, usb, SATA, whatever,) reset the BIOS, and if still no go reseat the proc and HSF (possible too much pressure, possible too much goo and it got onto the components)

 

920s are twitchy beasts.  I gave up on mine.

 

(If the PSU definitely isn't the problem I'd find a way to check the SSDs too.)

have you tried putting the original cpu cooler back on to see if it boots?

 

with your new cpu cooler did it come pre-applied with thermal paste or did you apply it when you switched out the coolers?

Disconnect the power connection for the new CPU Cooler (Fan?) to the motherboard and then try boot the system.

 

If it fixes the issue its the CPU Cooler.

 

p.s Just disconnect it for testing, don't keep using the computer as the CPU will probably overheat without the cooler with prolonged use.

I had a cooling fan that was plugging into a laptop causing the light to just blink but not turn on. After unplugging the cooling fan the laptop turned on. So maybe the fan is shorting it out or something.

Have you tried booting into safe mode to rule out windows being the problem?

http://www.howtogeek.com/107511/how-to-boot-into-safe-mode-on-windows-8-the-easy-way/

 

Where are these 'Clicks' coming from? hardware inside? speakers??

 

 

Also, does your graphics card have a separate power feed and is it plugged in correctly?

 

 

Whatever you do, do NOT try and turn on the PC without a heatsink attached.

 

 

Resetting the bios can sometimes also cause more problems. i.e it might disable SATA AHCI and revert to old IDE mode which will make windows fail to load if it is expecting it to be AHCI compatible.

  On 13/08/2014 at 22:12, kiddingguy said:

I just installed a new CPU cooler. Everything is attached again to my mobo (I think ok - haha)

When booting my PC gets into a loop and I cannot log into Windows. A clicking sound is made and than boots again.

What can be the issue for this reboot loop? Have I overlooked something or maybe not connected the right way?

I would triple check the hard drive connections.

 

Both the power connection and data cable -- including the cable to the motherboard.

 

You might swap out the data cable too, in case it is bad.

  On 15/08/2014 at 15:14, f1ux said:

Resetting the bios can sometimes also cause more problems. i.e it might disable SATA AHCI and revert to old IDE mode which will make windows fail to load if it is expecting it to be AHCI compatible.

True, though I'd expect people modding their comp to be aware of that and change it to the right setting, since they had to when they set up the comp in the first place.

  On 15/08/2014 at 14:55, GotBored said:
GotBored, on 15 Aug 2014 - 16:55, said:

Disconnect the power connection for the new CPU Cooler (Fan?) to the motherboard and then try boot the system.

 

If it fixes the issue its the CPU Cooler.

 

p.s Just disconnect it for testing, don't keep using the computer as the CPU will probably overheat without the cooler with prolonged use.

 

I tried this, but the BIOS error I get is that the CPU fan must be connected. No boot at all.

 

The old fan isn't working any more, so that won't be an option.

Tomorrow I will place the CPU once again and see if it's working. In the BIOS it's recognized. I applied the paste myself.

Keep you all posted.

I think it might have something to do with AHCI and IDE and some BIOS setting.

When quickly changing AHCI the clicks were gone, but an error message popped up that My computer/Windows has ran into trouble.

 

I will dig in this further tomorrow.

 

Thanks so far for the feedback!

If you're booting to windows it's not your PSU. The motherboard checks for sufficient power before even attempting to boot. If you have insufficient power, you might just hear fans running. An improperly mounted or insufficient heat sink would cause a thermal shutdown, not a reboot loop into Windows. If the CPU was damaged you wouldn't POST or get past the BIOS. I suspect you're hitting a blue screen in regards to the disk controller and the machine is configured to reboot on stop errors, hence the loop. Can you access the Windows boot options before it loads windows? Can you get into safe mode?

I've seen this issue recently, and it turned out that one of the RAM sticks was loose.  It occurred after cleaning dust out the case, so changing the orientation knocked it loose.

 

Not sure if it's the same issue you're seeing, but it's quick and easy to check.

  On 15/08/2014 at 15:50, kiddingguy said:

I tried this, but the BIOS error I get is that the CPU fan must be connected. No boot at all.

 

The old fan isn't working any more, so that won't be an option.

Tomorrow I will place the CPU once again and see if it's working. In the BIOS it's recognized. I applied the paste myself.

Keep you all posted.

 

That's good, one of the fault conditions which will cause the system to boot cycle (or shutdown) is if the CPU Fan is not detected. Your BIOS gives you a warning message when this happens so its safe to say the fan is being recognized and doesn't have an internal short or open cct which could be causing the failures. Make sure no cables are getting stuck in the fan during operation and that it spins freely and you can rule out the cpu fan.

 

  On 15/08/2014 at 16:09, kiddingguy said:

I think it might have something to do with AHCI and IDE and some BIOS setting.

When quickly changing AHCI the clicks were gone, but an error message popped up that My computer/Windows has ran into trouble.

 

I will dig in this further tomorrow.

 

Thanks so far for the feedback!

 

Does it still try to do a boot cycle or is it staying in Windows now with an error message?

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Yup, a bit slow on some PCs at the time, but absolutely gorgeous.
    • That's essentially what I've been running on KDE
    • For some of us, we've never left! A lot of customization tools have allowed us to adopt a non-native glassy design.
    • iPadOS 26 is now official with improved windowing, menu bar, 'Liquid Glass' redesign, more by Taras Buria As expected, today, at WWDC 2025, Apple announced iOS 26 and other operating systems that now carry the 26 version number (for simplicity). iPadOS is also part of the big redesign, and it is now official with the new Liquid Glass design, improved window controls, a Mac-like menu bar, file management enhancements, and more. In addition to the general Liquid Glass redesign, which is now present across all of Apple's operating systems, iPadOS 26 received several iPad-exclusive upgrades. It now has a reworked windowing system that helps you organize and switch between apps. You can finally place and resize apps exactly how you want. Plus, iPadOS now has familiar window controls: three buttons for closing, minimizing, and resizing your app. Straight from macOS. Apps can now remember their previous size and position, and Expose can show you all open windows. Finally, iPadOS now has a menu bar, which is another thing that comes from macOS. It gives access to common actions, commands, and features. Developers can customize the menu bar in their apps and specify what features are available there. Apple is also upgrading the Files app with a reworked List view, which now shows more details about your files and the ability to expand or collapse folders. Plus, you can customize folders with colors and emojis, pin folders to the dock, and set default apps for file types. When working with long-running processes, background tasks show up as live activities, so that you can track Final Cut exports or the Files app moving stuff around. Other changes in iPadOS 26 include improved audio controls and the ability to select audio input source and record audio with voice isolation. The Journal app is now available on the iPad, Notes received markdown support, and Calculator now supports 3D graphing capabilities. You can learn more about iPadOS 26 in the official announcement post here.
    • That same Brave that tried to insert their own ads instead of blocked ones?
  • Recent Achievements

    • Rookie
      CHUNWEI went up a rank
      Rookie
    • Enthusiast
      the420kid went up a rank
      Enthusiast
    • Conversation Starter
      NeoToad777 earned a badge
      Conversation Starter
    • Week One Done
      VicByrd earned a badge
      Week One Done
    • Reacting Well
      NeoToad777 earned a badge
      Reacting Well
  • Popular Contributors

    1. 1
      +primortal
      476
    2. 2
      +FloatingFatMan
      279
    3. 3
      ATLien_0
      255
    4. 4
      Edouard
      204
    5. 5
      snowy owl
      200
  • Tell a friend

    Love Neowin? Tell a friend!