Computer won't boot after new CPU cooler and gets into reboot


Recommended Posts

I just installed a new CPU cooler. Everything is attached again to my mobo (I think ok - haha)

When booting my PC gets into a loop and I cannot log into Windows. A clicking sound is made and than boots again.

The BIOS can be reached. I already have set everything to its default values, without success.

The CPU is recognized as well as the SSD that boots. The Windows 8.1 bootup screen is displayed and than a loop.

Afterwards the Repair mode is coming up.

What can be the issue for this reboot loop? Have I overlooked something or maybe not connected the right way?

I think it's the PSU dying or already dead... (the PSU is 5 years old and almost constantly on)

damn!

 

The sound is a clicking sound, and my computer gets in a constant reboot.

 

Question is, since I'm already thinking of getting a new PC, will I just get a new PSU or now a complete new PC, mobo/CPU and everything...?!

Don't expect a reply in here in 8 hours.

 

PSU's can often overload components, therefore creating electric whines.

 

Get a new PSU. You can use it for your next build.

I installed the new 860W Corsair PSU.

However, problem is still there.

 

What I see:

- the BIOS is displayed

- the Windows 8 bootcircle

- 2 clicks

- Windows bootcircle continues spinning

- that the reboot

 

After that a screen is displayed "Preparing Automatic Repair" which cannot repair anything....

 

Help! What might be the issue here?

It's a cold boot after a day or so not used. Overheating can still happen than?

Before replacing my CPU cooler Windows did boot normally, although the clicks were still there (that's why I initially replaced only the CPU cooler)

I'd check all your connectors in case something got knocked loose in the process (fans, usb, SATA, whatever,) reset the BIOS, and if still no go reseat the proc and HSF (possible too much pressure, possible too much goo and it got onto the components)

 

920s are twitchy beasts.  I gave up on mine.

 

(If the PSU definitely isn't the problem I'd find a way to check the SSDs too.)

have you tried putting the original cpu cooler back on to see if it boots?

 

with your new cpu cooler did it come pre-applied with thermal paste or did you apply it when you switched out the coolers?

Disconnect the power connection for the new CPU Cooler (Fan?) to the motherboard and then try boot the system.

 

If it fixes the issue its the CPU Cooler.

 

p.s Just disconnect it for testing, don't keep using the computer as the CPU will probably overheat without the cooler with prolonged use.

I had a cooling fan that was plugging into a laptop causing the light to just blink but not turn on. After unplugging the cooling fan the laptop turned on. So maybe the fan is shorting it out or something.

Have you tried booting into safe mode to rule out windows being the problem?

http://www.howtogeek.com/107511/how-to-boot-into-safe-mode-on-windows-8-the-easy-way/

 

Where are these 'Clicks' coming from? hardware inside? speakers??

 

 

Also, does your graphics card have a separate power feed and is it plugged in correctly?

 

 

Whatever you do, do NOT try and turn on the PC without a heatsink attached.

 

 

Resetting the bios can sometimes also cause more problems. i.e it might disable SATA AHCI and revert to old IDE mode which will make windows fail to load if it is expecting it to be AHCI compatible.

  On 13/08/2014 at 22:12, kiddingguy said:

I just installed a new CPU cooler. Everything is attached again to my mobo (I think ok - haha)

When booting my PC gets into a loop and I cannot log into Windows. A clicking sound is made and than boots again.

What can be the issue for this reboot loop? Have I overlooked something or maybe not connected the right way?

I would triple check the hard drive connections.

 

Both the power connection and data cable -- including the cable to the motherboard.

 

You might swap out the data cable too, in case it is bad.

  On 15/08/2014 at 15:14, f1ux said:

Resetting the bios can sometimes also cause more problems. i.e it might disable SATA AHCI and revert to old IDE mode which will make windows fail to load if it is expecting it to be AHCI compatible.

True, though I'd expect people modding their comp to be aware of that and change it to the right setting, since they had to when they set up the comp in the first place.

  On 15/08/2014 at 14:55, GotBored said:
GotBored, on 15 Aug 2014 - 16:55, said:

Disconnect the power connection for the new CPU Cooler (Fan?) to the motherboard and then try boot the system.

 

If it fixes the issue its the CPU Cooler.

 

p.s Just disconnect it for testing, don't keep using the computer as the CPU will probably overheat without the cooler with prolonged use.

 

I tried this, but the BIOS error I get is that the CPU fan must be connected. No boot at all.

 

The old fan isn't working any more, so that won't be an option.

Tomorrow I will place the CPU once again and see if it's working. In the BIOS it's recognized. I applied the paste myself.

Keep you all posted.

I think it might have something to do with AHCI and IDE and some BIOS setting.

When quickly changing AHCI the clicks were gone, but an error message popped up that My computer/Windows has ran into trouble.

 

I will dig in this further tomorrow.

 

Thanks so far for the feedback!

If you're booting to windows it's not your PSU. The motherboard checks for sufficient power before even attempting to boot. If you have insufficient power, you might just hear fans running. An improperly mounted or insufficient heat sink would cause a thermal shutdown, not a reboot loop into Windows. If the CPU was damaged you wouldn't POST or get past the BIOS. I suspect you're hitting a blue screen in regards to the disk controller and the machine is configured to reboot on stop errors, hence the loop. Can you access the Windows boot options before it loads windows? Can you get into safe mode?

I've seen this issue recently, and it turned out that one of the RAM sticks was loose.  It occurred after cleaning dust out the case, so changing the orientation knocked it loose.

 

Not sure if it's the same issue you're seeing, but it's quick and easy to check.

  On 15/08/2014 at 15:50, kiddingguy said:

I tried this, but the BIOS error I get is that the CPU fan must be connected. No boot at all.

 

The old fan isn't working any more, so that won't be an option.

Tomorrow I will place the CPU once again and see if it's working. In the BIOS it's recognized. I applied the paste myself.

Keep you all posted.

 

That's good, one of the fault conditions which will cause the system to boot cycle (or shutdown) is if the CPU Fan is not detected. Your BIOS gives you a warning message when this happens so its safe to say the fan is being recognized and doesn't have an internal short or open cct which could be causing the failures. Make sure no cables are getting stuck in the fan during operation and that it spins freely and you can rule out the cpu fan.

 

  On 15/08/2014 at 16:09, kiddingguy said:

I think it might have something to do with AHCI and IDE and some BIOS setting.

When quickly changing AHCI the clicks were gone, but an error message popped up that My computer/Windows has ran into trouble.

 

I will dig in this further tomorrow.

 

Thanks so far for the feedback!

 

Does it still try to do a boot cycle or is it staying in Windows now with an error message?

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Microsoft SharePoint gets Modern Page Templates to speed up page creation by Paul Hill SharePoint, Microsoft’s enterprise content management solution that allows organizations to set up internal pages and share documents, has just got a big update with the new Modern Page Templates. Microsoft said that it’s going to be rolling out the feature to customers globally between early July and early August. Organization members that want to set up pages on SharePoint using the new templates can do so from multiple entry points including the Site Home (the home of a Communication or Teams site), App Bar (the persistent navigation pane on the left of SharePoint), and the New Web Part (a webpart that displays and creates news posts directly on pages). By giving colleagues multiple access points to the new templates, there’s more chance they’ll be found and used. By including plenty of swanky templates, Microsoft is making it so you can spend less time designing pages, and more time filling them with content that really matters. If you want to create a new page using the templates, just go to New > Page and select a template “From Microsoft”. If you were making a news post, you would go to New > News post then you’d be presented with the new Template Gallery where you can select a custom template created by your colleagues under “Saved on this site”. While these new templates are coming to customers globally next month, Microsoft is already busy working on new features to make templates easier to discover and make them more useful. For example, it is building tenant-wide custom templates that can be published across sites for organization-wide use, and it’s working on Copilot templates that you can use when creating pages with Copilot. Neither of these features was given a release timeline. Customers won’t need to do anything to start using Modern Page Templates as they’ll be available automatically as it rolls out worldwide across tenants. For those who want to dive deeper, Microsoft will be publishing additional documentation and guidance about this feature soon.
    • Times are changing: https://arstechnica.com/gaming...ndows-11-ars-testing-finds/
    • Unless there is “bug” that all of a sudden sends your messages to Meta. Where have I heard this before?!
    • Maybe, just maybe... and it isn't you... there are some people who like the Windows 11 UI (for whatever reason) and want a better backend.
    • Gundams to arrive in Call of Duty: Mobile with new mech mode and unique third-person combat by Paul Hill Activision has announced that Call of Duty: Mobile will see the launch of Season 6 “Gundams Arrive” on July 2 at 5PM Pacific Time. This major collaboration between the world’s most popular FPS franchise and the Gundam franchise will introduce a new, limited-time mode called Gundam Team Deathmatch where 8 players will face off 4v4 and pilot Gundam-themed operators such as Ethan - Freedom Gundam, Reaper - Sazabi Gundam, Proton - v Gundamo, Deathscythe Gundam (EW). When playing in this game mode, players will notice a switch from the usual first-person view to the third-person perspective. The new game mode will also feature specific abilities and weapons that are unique to Gundam suits rather than player loadouts. The new Gundam Team Deathmatch mode will be played on a new map called interstellar space station, which has been designed for this mode. When playing, you’ll discover that the mech suits offer specialized mobility such as dodge, sprint, and vertical jets. In the post-match, players will be able to watch Gundam operator animations with unlockable rewards for viewing. You can unlock more animations by participating in Gundam Team Deathmatch, normal Multiplayer, and Battle Royale modes. There will also be Gundam-themed in-game events, such as Survival of the Fittest, which will give players free rewards like the new legendary weapon J358 — Fin Funnel v Gundam, Urban Tracker — Defense Force, Cyro Bomb — Haro (reskin), Emote — Haro Team, new camos, and more. Players will also be able to obtain a variety of items through Season 6 Battle Pass free and premium tiers, including sci-fi-themed Operators and Weapon Blueprints. Players on the free tier will get access to the bolt-action 3-Line Rifle based on a World War II design and is capable of inflicting high damage with high accuracy. Free tier players will also have the chance to earn other rewards such as Skins, Weapons Blueprints, Vault Coins, and more. Players looking to spend money can get the Premium Pass. These players will have a chance to get all of the content from Season 6 including tactical warriors like Silver — Chrome Dome Reskin, Misty — Science Pilot, Atlas — Dust Ranger, and The Marshal — Rock Hound; and Weapon Blueprints like the BP50 — Pathripper, Oden — Maevwat Technical, PDW-57 — Rocket Re-Entry, BY15 — Dark Moon, and the 3-Line Rifle — Geo Thermal Line, based on the new Season 6 weapon. There’s also Battle Pass Subscription which gives you additional monthly rewards along with a 10% boost to Player and Weapon XP, discount coupons, and limited discounts on 10x crate pulls. Activision also stated that Mythic Drops are returning to the Mythic store and that Battle Pass Vault is getting Season 9 — Zombies Are Back (2022) and Season 6 — Templar's Oath (2023).
  • Recent Achievements

    • Week One Done
      pcdoctorsnet earned a badge
      Week One Done
    • Rising Star
      Phillip0web went up a rank
      Rising Star
    • One Month Later
      Epaminombas earned a badge
      One Month Later
    • One Year In
      Bert Fershner earned a badge
      One Year In
    • Reacting Well
      ChrisOdinUK earned a badge
      Reacting Well
  • Popular Contributors

    1. 1
      +primortal
      543
    2. 2
      ATLien_0
      205
    3. 3
      +FloatingFatMan
      171
    4. 4
      Michael Scrip
      150
    5. 5
      Som
      128
  • Tell a friend

    Love Neowin? Tell a friend!