Computer won't boot after new CPU cooler and gets into reboot


Recommended Posts

I just installed a new CPU cooler. Everything is attached again to my mobo (I think ok - haha)

When booting my PC gets into a loop and I cannot log into Windows. A clicking sound is made and than boots again.

The BIOS can be reached. I already have set everything to its default values, without success.

The CPU is recognized as well as the SSD that boots. The Windows 8.1 bootup screen is displayed and than a loop.

Afterwards the Repair mode is coming up.

What can be the issue for this reboot loop? Have I overlooked something or maybe not connected the right way?

I think it's the PSU dying or already dead... (the PSU is 5 years old and almost constantly on)

damn!

 

The sound is a clicking sound, and my computer gets in a constant reboot.

 

Question is, since I'm already thinking of getting a new PC, will I just get a new PSU or now a complete new PC, mobo/CPU and everything...?!

Don't expect a reply in here in 8 hours.

 

PSU's can often overload components, therefore creating electric whines.

 

Get a new PSU. You can use it for your next build.

I installed the new 860W Corsair PSU.

However, problem is still there.

 

What I see:

- the BIOS is displayed

- the Windows 8 bootcircle

- 2 clicks

- Windows bootcircle continues spinning

- that the reboot

 

After that a screen is displayed "Preparing Automatic Repair" which cannot repair anything....

 

Help! What might be the issue here?

It's a cold boot after a day or so not used. Overheating can still happen than?

Before replacing my CPU cooler Windows did boot normally, although the clicks were still there (that's why I initially replaced only the CPU cooler)

I'd check all your connectors in case something got knocked loose in the process (fans, usb, SATA, whatever,) reset the BIOS, and if still no go reseat the proc and HSF (possible too much pressure, possible too much goo and it got onto the components)

 

920s are twitchy beasts.  I gave up on mine.

 

(If the PSU definitely isn't the problem I'd find a way to check the SSDs too.)

have you tried putting the original cpu cooler back on to see if it boots?

 

with your new cpu cooler did it come pre-applied with thermal paste or did you apply it when you switched out the coolers?

Disconnect the power connection for the new CPU Cooler (Fan?) to the motherboard and then try boot the system.

 

If it fixes the issue its the CPU Cooler.

 

p.s Just disconnect it for testing, don't keep using the computer as the CPU will probably overheat without the cooler with prolonged use.

I had a cooling fan that was plugging into a laptop causing the light to just blink but not turn on. After unplugging the cooling fan the laptop turned on. So maybe the fan is shorting it out or something.

Have you tried booting into safe mode to rule out windows being the problem?

http://www.howtogeek.com/107511/how-to-boot-into-safe-mode-on-windows-8-the-easy-way/

 

Where are these 'Clicks' coming from? hardware inside? speakers??

 

 

Also, does your graphics card have a separate power feed and is it plugged in correctly?

 

 

Whatever you do, do NOT try and turn on the PC without a heatsink attached.

 

 

Resetting the bios can sometimes also cause more problems. i.e it might disable SATA AHCI and revert to old IDE mode which will make windows fail to load if it is expecting it to be AHCI compatible.

  On 13/08/2014 at 22:12, kiddingguy said:

I just installed a new CPU cooler. Everything is attached again to my mobo (I think ok - haha)

When booting my PC gets into a loop and I cannot log into Windows. A clicking sound is made and than boots again.

What can be the issue for this reboot loop? Have I overlooked something or maybe not connected the right way?

I would triple check the hard drive connections.

 

Both the power connection and data cable -- including the cable to the motherboard.

 

You might swap out the data cable too, in case it is bad.

  On 15/08/2014 at 15:14, f1ux said:

Resetting the bios can sometimes also cause more problems. i.e it might disable SATA AHCI and revert to old IDE mode which will make windows fail to load if it is expecting it to be AHCI compatible.

True, though I'd expect people modding their comp to be aware of that and change it to the right setting, since they had to when they set up the comp in the first place.

  On 15/08/2014 at 14:55, GotBored said:
GotBored, on 15 Aug 2014 - 16:55, said:

Disconnect the power connection for the new CPU Cooler (Fan?) to the motherboard and then try boot the system.

 

If it fixes the issue its the CPU Cooler.

 

p.s Just disconnect it for testing, don't keep using the computer as the CPU will probably overheat without the cooler with prolonged use.

 

I tried this, but the BIOS error I get is that the CPU fan must be connected. No boot at all.

 

The old fan isn't working any more, so that won't be an option.

Tomorrow I will place the CPU once again and see if it's working. In the BIOS it's recognized. I applied the paste myself.

Keep you all posted.

I think it might have something to do with AHCI and IDE and some BIOS setting.

When quickly changing AHCI the clicks were gone, but an error message popped up that My computer/Windows has ran into trouble.

 

I will dig in this further tomorrow.

 

Thanks so far for the feedback!

If you're booting to windows it's not your PSU. The motherboard checks for sufficient power before even attempting to boot. If you have insufficient power, you might just hear fans running. An improperly mounted or insufficient heat sink would cause a thermal shutdown, not a reboot loop into Windows. If the CPU was damaged you wouldn't POST or get past the BIOS. I suspect you're hitting a blue screen in regards to the disk controller and the machine is configured to reboot on stop errors, hence the loop. Can you access the Windows boot options before it loads windows? Can you get into safe mode?

I've seen this issue recently, and it turned out that one of the RAM sticks was loose.  It occurred after cleaning dust out the case, so changing the orientation knocked it loose.

 

Not sure if it's the same issue you're seeing, but it's quick and easy to check.

  On 15/08/2014 at 15:50, kiddingguy said:

I tried this, but the BIOS error I get is that the CPU fan must be connected. No boot at all.

 

The old fan isn't working any more, so that won't be an option.

Tomorrow I will place the CPU once again and see if it's working. In the BIOS it's recognized. I applied the paste myself.

Keep you all posted.

 

That's good, one of the fault conditions which will cause the system to boot cycle (or shutdown) is if the CPU Fan is not detected. Your BIOS gives you a warning message when this happens so its safe to say the fan is being recognized and doesn't have an internal short or open cct which could be causing the failures. Make sure no cables are getting stuck in the fan during operation and that it spins freely and you can rule out the cpu fan.

 

  On 15/08/2014 at 16:09, kiddingguy said:

I think it might have something to do with AHCI and IDE and some BIOS setting.

When quickly changing AHCI the clicks were gone, but an error message popped up that My computer/Windows has ran into trouble.

 

I will dig in this further tomorrow.

 

Thanks so far for the feedback!

 

Does it still try to do a boot cycle or is it staying in Windows now with an error message?

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • KataLib 4.5.3.0 by Razvan Serea KataLib is more than just a music player — it's a complete audio suite designed for music lovers and creators alike. It combines a powerful audio player, a flexible metadata editor, a capable audio converter, and a music library manager into one streamlined application. Core Features: Audio Player Enjoy seamless playback of virtually any audio format or even streaming video files. DJ Mode lets you mix tracks with manual or automatic crossfades. You can also load and save WinAmp-style playlists for quick access to your favorite sets. Audio Converter Convert between a wide range of audio formats effortlessly. Trim or normalize your output automatically, and even extract audio from streaming video sources. Ideal for preparing files for different devices or platforms. Metadata Editor View and edit ID3v2 tags and other metadata. Batch edit multiple files at once, and fetch missing information directly from the MusicBrainz database. You can also apply or update album art with ease. Music Library Manager Organize your entire audio collection, search across tracks instantly, and download cover images from the internet — or use your own custom artwork. KataLib makes it easy to keep your library tidy and enriched with useful info. Supported Formats: KataLib supports a wide range of both lossy and lossless audio formats: Input: OPUS, AAC, FLAC, M4A, MP3, MP4, MPC, APE, AIF, MKV, AVI, MOV, FLV, WEBM, Ogg Vorbis, WAV, WAVPack, WMA Output: OPUS, FLAC, M4A, MP3, Ogg Vorbis, WAV Under the hood, KataLib uses the trusted FFmpeg engine for audio conversion and media playback, ensuring compatibility with virtually all mainstream media formats. Download: KataLib 4.5.3.0 | 64.5 MB (Open Source) Links: KataLib Home Page | Github | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • I had this issue and it is a nova android conflict issue. Initially the only way to fix it was clicking the screen off and then back on. Figured out it was because of a task I set up in tasker to load certain apps when I connect to my car, so fixed it by adding a 'go home' task after the app loaded and rarely have the issue now
    • I wish one of the windows updates hadn't broken glass. Is there a workaround for that I'm not aware of?
    • OpenAI announces o3 Pro, its most intelligent reasoning model by Pradeep Viswanathan OpenAI today announced o3-pro, its flagship reasoning model that uses more compute to "think harder" and provide consistently better answers. This new model will be replacing o1-pro in ChatGPT since it consistently performs better in math, science, and coding. To help everyone make the most out of the model, o3-pro supports tool calling. So, based on the user prompt, the model can do a web search, analyze files, reason about visual inputs, use Python, personalize responses using memory, and more. This is a big improvement over o1-pro, which lacked access to tools. But the downside is that o3-pro will take more time to respond. OpenAI recommends users use o3-pro in cases where reliability matters more than speed. According to OpenAI's evaluations, users consistently preferred o3-pro's responses over o3 in key domains like science, education, programming, business, and writing help. o3-pro was also rated consistently higher for clarity, comprehensiveness, instruction-following, and accuracy. The new o3-pro model is available in ChatGPT's model picker for Pro and Team. ChatGPT's Enterprise and Edu users will get access to this latest model next week. For developers, the o3-pro model comes with a 200,000 context window and is priced at $20 per million input tokens and $80 per million output tokens. OpenAI recommends developers use background mode with o3-pro to prevent timeouts. And the model has a May 31, 2024 knowledge cutoff. The OpenAI team also noted the following as the current limitations of the o3-pro model: At the moment, temporary chats are disabled for o3-pro as we resolve a technical issue. Image generation is not supported within o3-pro—please use GPT-4o, OpenAI o3, or OpenAI o4-mini to generate images. Canvas is also currently not supported within o3-pro. As OpenAI continues to refine its models, the balance between speed and reliability will likely remain a key consideration for users choosing the right tool for their needs.
  • Recent Achievements

    • Reacting Well
      rshit earned a badge
      Reacting Well
    • Reacting Well
      Alan- earned a badge
      Reacting Well
    • Week One Done
      IAMFLUXX earned a badge
      Week One Done
    • One Month Later
      Æhund earned a badge
      One Month Later
    • One Month Later
      CoolRaoul earned a badge
      One Month Later
  • Popular Contributors

    1. 1
      +primortal
      541
    2. 2
      ATLien_0
      269
    3. 3
      +FloatingFatMan
      210
    4. 4
      +Edouard
      203
    5. 5
      snowy owl
      140
  • Tell a friend

    Love Neowin? Tell a friend!