How much damage can I get hitting a speed bump slightly overspeed?


Recommended Posts

This weekend I took a drive out to Valley Forge Historic Park and while entering a parking lot I hit a very poorly marked speedbump. I was going probably 10 or 15mph over this bump, but the car definitely rocked up and down as I passed it faster than I was intended to...

 

I didn't hear any major scraping or feel anything serious. I looked under the car from the sides (not via a jack or lift) and couldn't see any major damage and I didn't have fluids leaking. The car also seemed to handle the drive back to Philadelphia. But I'm not sure if there is anything I should be checking to see what I could have damaged on this bump.

 

For you more seasoned drivers I'm sure this has happened at least once or twice. What do you normally check for and etc?

Lol, I used to hit those at speed. 

 

No scraping, no problem.  If you do it often though, you will eventually have issues with your shocks/struts.  No big deal just once though.

 

Let me know when you hit a curb, that has some checking to do if you hit above 5mph.  That can really screw your world up (bent tie rods, bent ball joints, steering rack, half shafts, rims...lots of stuff).

Lol, I used to hit those at speed. 

 

No scraping, no problem.  If you do it often though, you will eventually have issues with your shocks/struts.  No big deal just once though.

There was minor scrapping I saw on one side of the car (if I am good at figuring out minor), But I couldn't tell if this was new or not since I purchased the car used a little over 2 weeks ago.

in fact, you can do over them at much faster speed.... and you have to do it repeatedly many many many times, and then over the period of time,

you will finally have tangible results, in loose joints and gearings...

 

 

but it will not show up until many many more high speed hits.    so it is not something you should worry about at all, considering how new your car is.

  • Like 1

did you ride over it or did you side swipe it?

I rode over it. I realized it was the case as the car jumped up and it was too late to do much other than ride it out.

 

in fact, you can do over them at much faster speed.... and you have to do it repeatedly many many many times, and then over the period of time,

you will finally have tangible results, in loose joints and gearings...

 

 

but it will not show up until many many more high speed hits.    so it is not something you should worry about at all, considering how new your car is.

 

Thanks!

Depends on the bump.

There was one in my old home town that was like a rock face, you couldn't go over it at any speed without some nasty sounding noises.

In general though you should be all good.

i rode over big pothole at 50 mph, and had the tire blowout (extreme case -  yet, besides the tire, and the rims balancing, no serious consequence!)

 

tons of speed bump, etc...

 

after 2 year of heavy riding, some thing got a bit loose... and my (honest, not dealership scum) mechanic told me that some of the things are starting to move around, and the total cost to replace is a few hundred.

even then, he said i am good to go for another few month, before replacing, if i want to save money.

cars nowadays are build to handle all kinds of rough treatments, without serious issues, and newer Mercedes are a solid build machines.

 

the only thing is, the dealership mechanics think you are an idiot, and like to charge extra to replace parts that otherwise don't need replacement. 

the parts they can easily resell to the other used car mechanics at a premium.

in fact, it is sickening, just how much scam is happening in car repair world, if you come in uninformed!

 

 

 

 

unless you have free maintenance in your dealership..  i highly recommend you find someone who know cars, or someone who can recommend a trustworthy mechanic who deal in euro cars..

it will save you a ton of money in the long run!  

 

 

i have had BMW and AUDI and in both cases, the dealership i trusted, ripped me off for so much money, i hated it!   i should have went with trustworthy independent from day 1!

i have had BMW and AUDI and in both cases, the dealership i trusted, ripped me off for so much money, i hated it!   i should have went with trustworthy independent from day 1!

 

:/  You know that these dealers charge premium for any work they do outside of warranty, right?  I barely trust the mid tiered dealerships to do anything outside of warranty work.  They like to nickel and dime you to death and go beyond what is wrong to fix the issue. Oh you need an oil change, while I was changing your oil I noticed a hole in your exhaust pipe, it is about 4 inches long, we need to fix that for you....mfer that wasn't there before you got the car, wtf did you hit....nothing sir that was like it when you brought it in....I would think I would notice my car sounding like a truck......

  • Like 1

:/  You know that these dealers charge premium for any work they do outside of warranty, right?  I barely trust the mid tiered dealerships to do anything outside of warranty work.  They like to nickel and dime you to death and go beyond what is wrong to fix the issue. Oh you need an oil change, while I was changing your oil I noticed a hole in your exhaust pipe, it is about 4 inches long, we need to fix that for you....mfer that wasn't there before you got the car, wtf did you hit....nothing sir that was like it when you brought it in....I would think I would notice my car sounding like a truck......

 

exactly..     i cannot believe they would do something like that.   but hell yeah, they DO.

:/  You know that these dealers charge premium for any work they do outside of warranty, right?  I barely trust the mid tiered dealerships to do anything outside of warranty work.  They like to nickel and dime you to death and go beyond what is wrong to fix the issue. Oh you need an oil change, while I was changing your oil I noticed a hole in your exhaust pipe, it is about 4 inches long, we need to fix that for you....mfer that wasn't there before you got the car, wtf did you hit....nothing sir that was like it when you brought it in....I would think I would notice my car sounding like a truck......

oh heck, I still haven't had a steering issue fixed on my car that I bought brand new... 3yrs of warranty work they never fixed the problem... replaced every part of it but the wheel itself, still have a sound coming from the steering system like water running through a hose... they even replaced the steering pump multiple times... never fixed it... took it to another dealer since the independent shops won't look at it as it's a "dealer issue" that dealer went straight to "you need a new steering fluid pump" about banged my head on the desk when I said it's been changed multiple times now that's not the issue!......

Had a VW i owned totalled in AZ for hail damage.  I was able to drive the car home and had to park it at my house while a I wanted a few days for a trailer to come by and pick it up.  So I drove the card hard and went over speed bumps going 45mph.  Didnt damage the car any.

  • Like 1

Had a VW i owned totalled in AZ for hail damage.  I was able to drive the car home and had to park it at my house while a I wanted a few days for a trailer to come by and pick it up.  So I drove the card hard and went over speed bumps going 45mph.  Didnt damage the car any.

only your neck and spine :rofl:

oh heck, I still haven't had a steering issue fixed on my car that I bought brand new... 3yrs of warranty work they never fixed the problem... replaced every part of it but the wheel itself, still have a sound coming from the steering system like water running through a hose... they even replaced the steering pump multiple times... never fixed it... took it to another dealer since the independent shops won't look at it as it's a "dealer issue" that dealer went straight to "you need a new steering fluid pump" about banged my head on the desk when I said it's been changed multiple times now that's not the issue!......

3+ times at the shop for the same thing = lemon law.

3+ times at the shop for the same thing = lemon law.

Oh no... it was never the same thing because they always "fixed it" the problem would slightly change into another problem with the same system so they could get around the issue.. darn dealers and GM dragging their feet for 3yrs until Pontiac was dismantled as a consumer brand... then the dealer started doing the "they no longer exist" excuse even though GM said the warranties were still valid

  • 1 year later...

I found this forum because I was worried about my 2015 WRX. I was switching freeways and was driving 74 mph on the junction. The freeway was smooth until I hit a little bump or something and the car lifted up, not off the ground, and landed hard. I'm just glad I still had control. I'm just worried about premature wear and tear. I always drive fast on that junction, just not the lane I was on.

wheel alignment probably. 

 

how does it feel?  if it were a major issue you would certainly feel it.    On a straight road, like highway, when you take your hands off the wheel does it drift out of the lane?  How fast will depend on how out of whack your alignment is. 

 

If not out of whack, monitor your tire wear on the inside tread and outside tread of each tire.  This may take months to get to a noticeable difference, use a penny or other coin to check depth. 

  • 4 weeks later...

Firstly look where you are going in the future instead of playing with yourself!

 

As for any possible damage, if a US built car (which are all poorly built) there will be a fair bit of damage viz broken springs, muffler blowing, damaged wheel rims.

 

However the single major issue you will have is the chassis frame will be twisted, get it checked now!

Wtf is going on? A 1 poster who somehow found this forum to make a car post and then some other one poster who is trashing all US built cars (even though the first 1 post guy said it was a WRX) and telling the guy he twisted his chassis. Phenomenal.

  • 3 weeks later...
On 2/1/2016 at 2:13 PM, Fingringhoe said:

Firstly look where you are going in the future instead of playing with yourself!

 

As for any possible damage, if a US built car (which are all poorly built) there will be a fair bit of damage viz broken springs, muffler blowing, damaged wheel rims.

 

However the single major issue you will have is the chassis frame will be twisted, get it checked now!

don't know much about cars do you.  If you did you would know that all cars go through vigorous testing to be on the roads in the US.  A speed bump, at any speed, will not twist the frame.  Twisting the frame will require a different kind of impact.  Other things can get twisted, but the frame will not...if it did every car sold in the us would have that issue.  Now you want to talk about overall build quality, rattles, and other issues I have no problems with...that garbage you spewed is garbage. 

 

Lets go onto damaged wheels and rims, american vs everyone else.  This would come down to the the tire build, not the rim or the make of the vehicle, but again a speed bump at any speed will not harm them....now if he hit a curb or a pothole that could swallow the whole front end, well then the rims could get damaged and the tire would likely be blown (seen that happen). 

 

  If you had a low car, you could scrape the under carriage or bend/break something under there...but the likely hood of broken springs aren't so likely even if you hit a speed bump at 100 mph...other parts sure, springs not so much. 

 

So what exactly would break being that the only thing that is plausible in your statement is the muffler.  a arms might get tweaked (a unlikely might), tie rods could be shot, the ball joints may be effected (if hit enough times), the rack could be damaged if hit hard enough, shock/struts could be shot if this is repeated constantly (these will fail way before the springs will), probably screw up your mid pipe/catalytic converters and muffler if it is low enough and you hit it so hard that you really compress your suspension to the point you scrape or hit the speed bump with those parts.  Might screw up your controlling arm.

 

None of these parts are really stronger or weaker on American vs other cars....at least not to the point where they will fall apart.  They all have to pass stringent testing to be able to be put on the roads, all of they have had a model that has been totaled on purpose (yes even the veyron or whatever other expensive car you can think of). 

 

So what really is the issue with American cars, well their quality control is lacking for sure.  You may get squeaks and rattles and computer components that don't last as long as the foreign components which can lead to mechanical failure due to equipment operating out of spec.  This is the reason I will not own a dodge or Chrysler product again regardless of who owns it (fiat or anyone else).  Ford is hit or miss, probably on my last one now....started rattling way too soon.  Government Motors, will not purchase anything from those thieves.   Loved my 2 nissans, and like my toyota.  BMW, Audi and Mercedes do absolutely nothing for me (not really a german car fan), rather have a infiniti, lexus, or acura.  None will really fall apart like in the movies, well except Volkswagen (I swear that whole company puts gremlin eggs in their cars before they leave the assembly plant)....when there is an issue with one of them it is always an electrical issue that can't be tracked down.

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • No its not, there are ton of Youtube videos to get you started, what do you think people did before AI existed?
    • Read this in Humor Simpson 's voice, "Out of my way Moe".
    • You still can, its just under the Transform flyout for WordArt now
    • Likely nothing will be done in corporate America, there have been countless Tesla self-driving incidents. Then again, there have also been countless human operated incidents. It's literally daily news here in Canada, to the extent that it's now odd if we get a day where a collision doesn't get announced on the radio throughout the day...
    • SKG Hand Massager with Heat OS500 hands on by Steven Parker I was offered the chance to test out the SKG Hand Massager with Heat OS500, and full disclosure, they let me keep it regardless of my findings. Anyway, I jumped at the chance due to my long hours sitting at my desk, mousing around. Apologies for the knife cut across the top of the box; that was my doing, being a bit too heavy-handed with opening up the outer packaging. First up, what's in the box: SKG Hand Massager with Heat OS500 1x Type-C charging cable User Manual 1-Year Warranty (card) In short, everything you need to get started. According to the official Amazon listing, here are the key features: Full-Hand Air Compression: OS500 wraps your fingers, palm, and wrist with multi-chamber air compression for a complete hand relaxation experience. The extended massage chamber helps cover more of the hand and wrist area than standard palm-only hand massagers Palm Kneading with 6 Modes & 6 Intensities: Built-in palm kneading rollers add a hands-on massage feel, while 6 preset modes and 6 pressure levels let you choose the comfort level that fits your day—from gentle relaxation to a firmer full-hand massage 3 Heat Levels with Cooling Fan: Choose from 104°F, 113°F or 122°F warmth to suit different seasons and comfort preferences. The built-in cooling fan helps reduce stuffiness during heated sessions, keeping your hand feeling fresh and comfortable Easy Visual Display & Smart Timer: The digital image display clearly shows massage area, mode, intensity, heat level, and remaining time at a glance. Select 10, 15, or 20-minute sessions for quick office breaks, evening relaxation, or everyday hand care Rechargeable, Cordless & Comfortable: A 3000mAh battery supports over 90 minutes of full-function use on a full charge, with convenient USB-C charging. The soft inner lining, smooth ABS/PU finish, and premium black-gold design make OS500 ideal for home, office, or gifting With all that out of the way, here are my own findings. I gave it a try on both left and right hands, and as you can maybe see from the above YouTube Short, (sorry for the shaky video), my whole hand fits in, but my wrist barely enters the Hand Massager. I was able to push through a bit more with my fingertips extending out the other end to get a bit of massaging on the start of my wrist. Usage For some reason, there is a strap that is very difficult to fasten to my wrist with one hand. I am not sure what function it has, and it isn't mentioned in the user manual. The only thing I could find was in the product images that claimed "wrist precision". Unlike the Bob and Brad Hand Massager, this device does not massage the wrist anyway, even though a "wrist mode" is mentioned, which must be for smaller hands than I have, as it is mainly intended for the hand and fingers. In addition, for its steeper price, there are no disposable gloves provided in the box, which is a bit of an issue considering the internal cover (which appears to be elasticated nylon) cannot be removed for washing; so you are left with only one choice: always thoroughly wash your hands before using it. I can imagine this thing getting a bit grimy after a period of use, and that is a bit of a shame. With that said, the buttons on the device, from left to right, do the following: Heat button: 3-level heat control at 104°F, 113°F, or 122°F Mode button: Auto mode Circular mode Soothing mode Relax mode Palm and fingers mode Palm and wrist mode Intensity button: from (First-time users) 15Ka, 25Ka, 35Ka, 45Ka, 55Ka, 60Ka (Intensive relief) Knead button: on or off (6 pressure levels) Power button: Long-press to turn on or off Cooling button: turn on or off the cooling fan Also, in the product imagery, it states there are 36 "custom modes," but nowhere is it listed what these modes are. I can only imagine that they mean a combination of all of the above settings in different intensity levels. The device itself seems to rely on a single "kneading" mechanism located at the palm area of the hand, which spins when in use, and the other massage features are mainly utilized through the air sacs, increasing and decreasing at various levels on the hand and fingers. I am not sure it offered too much relief for someone who is typing and operating a mouse for hours at a time; further testing may be required. It does feel nice, though. Finally, you may be wondering how this fits into the scope of a tech website? Well, let me tell you something: sometimes I sit for up to 15 hours working on Neowin, and although I take breaks in between, it takes a toll on my body. I think in the immediate absence of a partner to apply relief, a good massager like this Hand Massager can shed the strains of the day in just a couple of 15-minute bursts. On the official website, this has an MSRP of $99.99, but luckily for our readers, it is selling at $10 off for just $89.99 right now on Amazon. SKG Hand Massager with Heat OS500 for $89.99 (with $10 off coupon), $99.99 MSRP For me, this gets a thumbs hands(?) down. However, it could be improved by making it so that the protective covering could be removed and thrown into the washing machine, or get yourself some disposable gloves to use with it. As an Amazon Associate, we earn from qualifying purchases.
  • Recent Achievements

    • Dedicated
      Almohandis earned a badge
      Dedicated
    • Dedicated
      JuvenileDelinquent earned a badge
      Dedicated
    • First Post
      DrWankel earned a badge
      First Post
    • Reacting Well
      DrWankel earned a badge
      Reacting Well
    • Week One Done
      Supreme Spray LV earned a badge
      Week One Done
  • Popular Contributors

    1. 1
      +primortal
      505
    2. 2
      +Edouard
      184
    3. 3
      PsYcHoKiLLa
      86
    4. 4
      Michael Scrip
      78
    5. 5
      Steven P.
      76
  • Tell a friend

    Love Neowin? Tell a friend!