Are the $100 dollars fuel injection services worth it?


Recommended Posts

I understand everyone is different. I'm just using the $100 dollars as an example that happened to me recently. 

 

I went to a national auto repair chain by my house. After the oil change (I had them put in full synthetic) the manager came over and talked to me about getting fuel injection cleaning done based on how many miles I have already  got on my vehicle. I declined the service.

 

Are these worth it or is it a scam? I prefer heading to an auto parts store and buying a fuel system cleaner for $10 dollars.

 

To some people $100 dollars is nothing. But to me it's a lot of money. 

 

My vehicle by the way currently has 126,000 miles on it. It runs fine too.

 

What do you think?

Never once did my MB had it done over 400.000km (bought it used and the last owner didn't even know what I was talking about). It's not a scam as far as I know but it's not something You really must to. Even more for 100 bucks.

not usually worth it depends on what there gonna do ask what there gonna do and dont let them mumle jumble you with jargon to make it seem fancy 

 

half of them are spray some stuff down your intake and/or dump some stuff into the gas not worth 100$ just trying to get an upsell

What can it hurt ? 
I heard many people are driving around with half-assed sparking spark plugs, and getting those replaced makes a big difference... I dont know though.

I hope you get a good, direct answer as many people voice their opinion as fact, and most opinions are based off of someone else's opinion.

I only use Royal Purple in both of my cars, and can tell you that there are a ton of people who think that is stupid...

Let me explain a little bit the difference between the 100 dollar one and the 10 dollar one. 

 

First off lets go with the 10 dollar one.  This one gets added and diluted in your fuel.  It is good if you keep up on it about once a month or once ever other fill up, depending on the 10 dollar version you are buying.  I personally like the Cheveron Techron brand.  But you should really ask yourself, what really is the difference between the fuel system cleaner and the fuel injection cleaner (they offer both).  Both go through your fuel system, essentially passing through the same components. 

 

Lets go to the 100 dollar one.  They either disable your fuel pump or disconnect your fuel lines and a machine with high concentrated cleaner blows through your injectors. 

 

The two are comparing a watered down drink to moonshine.  With enough of the watered down drink, you will eventually get drunk (you might be full before that happens though).  With moonshine at just about 200 proof, well you can imagine how fast you will get drunk.  One is very low concentration, one is very high concentration. 

 

I had an injector clogged, tried the intank stuff and failed miserably...then went to the high concentrated shut fuel system off stuff and it cleared it within minutes.  Working in parts I had access to a lot of stuff normal people dont have access to or rarely get a chance to see.

Let me explain a little bit the difference between the 100 dollar one and the 10 dollar one. 

 

First off lets go with the 10 dollar one.  This one gets added and diluted in your fuel.  It is good if you keep up on it about once a month or once ever other fill up, depending on the 10 dollar version you are buying.  I personally like the Cheveron Techron brand.  But you should really ask yourself, what really is the difference between the fuel system cleaner and the fuel injection cleaner (they offer both).  Both go through your fuel system, essentially passing through the same components. 

 

Lets go to the 100 dollar one.  They either disable your fuel pump or disconnect your fuel lines and a machine with high concentrated cleaner blows through your injectors. 

 

The two are comparing a watered down drink to moonshine.  With enough of the watered down drink, you will eventually get drunk (you might be full before that happens though).  With moonshine at just about 200 proof, well you can imagine how fast you will get drunk.  One is very low concentration, one is very high concentration. 

 

I had an injector clogged, tried the intank stuff and failed miserably...then went to the high concentrated shut fuel system off stuff and it cleared it within minutes.  Working in parts I had access to a lot of stuff normal people dont have access to or rarely get a chance to see.

But to what extent are they needed as regular maintenance ? on cars 1 year old? 5 ? 10? etc.

You should be treating with the intank almost immediately after you get the car to keep the carbon down. 

 

As far as the high concentrated one goes, it can be done at 50k but recommended at 100K.

 

Carbon builds up very very quickly...when you buy a new car the exhaust pipe is clean...in just a few hundred miles the inside turns black.  It doesn't take long for this to start building up in your engine.  To avoid excessive build up, drive your car often, don't let it sit for long periods of time, don't do a lot of city driving, or every 2 to 4 fill ups use a fuel system/injector cleaner. 

You should be treating with the intank almost immediately after you get the car to keep the carbon down. 

 

As far as the high concentrated one goes, it can be done at 50k but recommended at 100K.

 

Carbon builds up very very quickly...when you buy a new car the exhaust pipe is clean...in just a few hundred miles the inside turns black.  It doesn't take long for this to start building up in your engine.  To avoid excessive build up, drive your car often, don't let it sit for long periods of time, don't do a lot of city driving, or every 2 to 4 fill ups use a fuel system/injector cleaner. 

I've heard/read stories that unnecesary tank treatment Fs up the car, how true is that?

Just for reference, this is a kit that some smaller garages use.  The fittings are a few hundred dollars, the can of juice is about $20

 

Here is one of the more popular ones used by dealers and bigger shops.  This one is about $4000.


I've heard/read stories that unnecesary tank treatment Fs up the car, how true is that?

Again it depends on the treatment.  Some are garbage, some are good.  Hard to say.  Follow the label and you will be fine.  If you use the techron it says every 3000 miles.  For me that is about 4-5 fill ups or once a month.  You can do a little more at every other fill ups for a little while without negative effects.   Or if you go a while without doing it, you can do one every other for few cycles without hurting anything. 

Buy some Seafoam, pour it in your gas tank, and then follow the instructions on how to run with it.  It sometimes creates a ton of white smoke, so don't worry if that happens.

 

Though if your gas mileage isn't dipping lower than normal and the engine sounds fine, I don't think you have to worry about any sort of cleaning.

What can it hurt ? 

I heard many people are driving around with half-assed sparking spark plugs, and getting those replaced makes a big difference... I dont know though.

I hope you get a good, direct answer as many people voice their opinion as fact, and most opinions are based off of someone else's opinion.

I only use Royal Purple in both of my cars, and can tell you that there are a ton of people who think that is stupid...

Not the 95%of people in the racing, off-road, and hi end car industry. :)

My advise, as a former mechanic is first treat via the gas.  Run the gas down to about 1/3 of a tank, then add 2 bottles of Seafoam (works great) or any other cleaner like Lucas.  Drive it until it is at 1/8, then fill up all the way.  If your car is having issues like stuttering or pinging when your accelerate then you need to treat it.  

 

Watch the oil change places, they are a joke for the most part.  I have seen plenty of damage from their service.  Special with the change the oil every 3000 mile BS.  

 

I have successfully treated all my cars, (3 BMW 5 series, Mini Cooper, Jeep Cherokee).  I was able to buy two of the BMW at a low price because of the cars running poorly.  I treated them and there is no issues.  I treat them once every 5k-7k via the gas method.  

My advise, as a former mechanic is first treat via the gas.  Run the gas down to about 1/3 of a tank, then add 2 bottles of Seafoam (works great) or any other cleaner like Lucas.  Drive it until it is at 1/8, then fill up all the way.  If your car is having issues like stuttering or pinging when your accelerate then you need to treat it.  

 

Watch the oil change places, they are a joke for the most part.  I have seen plenty of damage from their service.  Special with the change the oil every 3000 mile BS.

 

I have successfully treated all my cars, (3 BMW 5 series, Mini Cooper, Jeep Cherokee).  I was able to buy two of the BMW at a low price because of the cars running poorly.  I treated them and there is no issues.  I treat them once every 5k-7k via the gas method.  

care to elaborate?

My advise, as a former mechanic is first treat via the gas.  Run the gas down to about 1/3 of a tank, then add 2 bottles of Seafoam (works great) or any other cleaner like Lucas.  Drive it until it is at 1/8, then fill up all the way.  If your car is having issues like stuttering or pinging when your accelerate then you need to treat it.  

 

Watch the oil change places, they are a joke for the most part.  I have seen plenty of damage from their service.  Special with the change the oil every 3000 mile BS.  

 

I have successfully treated all my cars, (3 BMW 5 series, Mini Cooper, Jeep Cherokee).  I was able to buy two of the BMW at a low price because of the cars running poorly.  I treated them and there is no issues.  I treat them once every 5k-7k via the gas method.  

I wouldn't necessarily jump to using fuel injector/system cleaner as a solution to pinging.  There are many causes to pinging, as a former mechanic you should know this and wouldn't immediately jump to cleaning your injectors as a solution.  Stuttering maybe, not pinging.  Excessive engine heat caused by a bad thermostat/water pump/radiator can cause pinging, a balancer that went bad can cause pinging, even fowled plugs can cause pinging.  Engine ticks can also be caused from faulty manufacturing (as it is with the ford 5.3L, look up cam phaser tick).  I would not suggest fuel injector cleaner until a diagnosis has been made as to probable cause when it comes to pinging. 

I wouldn't necessarily jump to using fuel injector/system cleaner as a solution to pinging.  There are many causes to pinging, as a former mechanic you should know this and wouldn't immediately jump to cleaning your injectors as a solution.  Stuttering maybe, not pinging.  Excessive engine heat caused by a bad thermostat/water pump/radiator can cause pinging, a balancer that went bad can cause pinging, even fowled plugs can cause pinging.  Engine ticks can also be caused from faulty manufacturing (as it is with the ford 5.3L, look up cam phaser tick).  I would not suggest fuel injector cleaner until a diagnosis has been made as to probable cause when it comes to pinging. 

 

True, let me clarify, stuttering and pinning at the same time.  Not knocking, when under stress (hard acceleration, going up hill, ect).

I honestly don't know, I buy a lot of old cars, simply to run them into the ground, and see how fast I can kill some models, but out of curiosity, I did get a power test done on a 1992 Mitsubishi Galant GTI, and it was still rocking 140some horses, I ragged on that car for 4-5 years before giving up on trying to kill it, got the power results and sold it, the whole time I owned that car, I never used any injector cleaner.

 

The other end of the scale, I never felt, or saw any improvements in the 8 or 9, Volvo 9 series I've owned and had used redex or paid for an engine decoke

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Hasleo Backup Suite Free 5.8.2.2 by Razvan Serea Hasleo Backup Suite Free is a free Windows backup and restore software, which embeds backup, restore and cloning features, it is designed for Windows operating system users and can be used on both Windows PCs and Servers. The backup and restore feature of Hasleo Backup Suite can help you back up and restore the Windows operating systems, disks, partitions and files (folders) to protect the security of your Windows operating system and personal data. The cloning feature of Hasleo Backup Suite can help you migrate Windows to another disk, or easily upgrade a disk to an SSD or a larger capacity disk. System Backup & Restore / Disk/Partition Backup & Restore Backup Windows operating system and boot-related partitions, including user settings, drivers and applications installed in these partitions, which ensures that you can quickly restore your Windows operating system once it crashes. Viruses, power failure, or other unknown reasons may cause data loss, so it is a good habit to regularly back up the drive that stores important files, you can at least recover lost files from the backup image files in the event of a disaster. System Clone / Disk Clone / Partition Clone Migrate the Windows operating system from one disk to another SSD or larger disk without reinstalling Windows, applications and drivers. Clone entire disk to another disk and ensure that the contents of the source disk and the destination disk are exactly the same. Clone a partition completely to the specified location on the current disk or another disk and ensure that the data will not be changed. File Backup & Restore Back up specified files(folders) instead of the entire drive to another location to protect your data, so you can quickly restore files(folders) from the backup image files when needed. Incremental/Differential/Full Backup Different backup modes are supported, you can flexibly choose data protection schemes, which can improve backup performance and save storage space while ensuring data security. Delta Restore Delta restore uses advanced delta detection technology to check the changed blocks on the destination drive and restore only the changed blocks, so it has a faster restore speed than the traditional full restore. Universal Restore This feature can help us restore the Windows operating system to computers with different hardware and ensure that Windows can work normally without any hardware compatibility issues. Hasleo Backup Suite 5.8.2.2 changelog: Improved creation of bootable media that supports the UEFI CA 2023 certificate Fixed an issue that caused system restore to fail Fixed an issue where file backup could not list drives under Windows ARM64 Fixed an issue that caused backup of MacOS files/folders shared via Samba to fail Fixed an issue that caused "Smart Backup" to not work properly Fixed other minor bugs Download: Hasleo Backup Suite 5.8.2.2 | 39.7 MB (Freeware) Links: Hasleo Backup Suite Website | Hasleo Backup Suite Guide | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • Shotcut 26.6.25 by Razvan Serea Shotcut is a free, open source, cross-platform video editor for Windows, Mac and Linux. Major features include support for a wide range of formats; no import required meaning native timeline editing; Blackmagic Design support for input and preview monitoring; and resolution support to 4k. Editing Features Trimming on source clip player or timeline with ripple option Append, insert, overwrite, lift, and ripple delete editing on the timeline 3-point editing Hide, mute, and lock track controls Multitrack timeline with thumbnails and waveforms Unlimited undo and redo for playlist edits including a history view Create, play, edit, save, load, encode, and stream MLT XML projects (with auto-save) Save and load trimmed clip as MLT XML file Load and play complex MLT XML file as a clip Drag-n-drop files from file manager Scrubbing and transport control Video Effects Video compositing across video tracks HTML5 (sans audio and video) as video source and filters 3-way (shadows, mids, highlights) color wheels for color correction and grading Eye dropper tool to pick neutral color for white balancing Deinterlacing Auto-rotate Fade in/out audio and fade video from and to black with easy-to-use fader controls on timeline Video wipe transitions: bar, barn door, box, clock (radial), diagonal, iris, matrix, and custom gradient image Track compositing/blending modes: Over, Add, Saturate, Multiply, Screen, Overlay, Darken, Dodge, Burn, Hard Light, Soft Light, Difference, Exclusion, HSL Hue, HSL Saturation, HSL Color, HSL Luminosity. Video Filters: Alpha Channel: Adjust, Alpha Channel: View, Blur, Brightness, Chroma Key: Advanced, Chroma Key: Simple, Contrast, Color Grading, Crop, Diffusion, Glow, Invert Colors, Key Spill: Advanced, Key Spill: Simple, Mirror, Old Film: Dust, Old Film: Grain, Old Film: Projector, Old Film: Scratches, Old Film: Technocolor, Opacity, Rotate, Rutt-Etra-Izer, Saturation, Sepia Tone, Sharpen, Size and Position, Stabilize, Text, Vignette, Wave, White Balance Speed effect for audio/video clips Hardware Support Blackmagic Design SDI and HDMI for input and preview monitoring Leap Motion for jog/shuttle control Webcam capture Audio capture to system audio card Capture (record) SDI, HDMI, webcam (V4L2), JACK audio, PulseAudio, IP stream, X11 screen, and Windows DirectShow devices Multi-core parallel image processing (when not using GPU and frame-dropping is disabled) DeckLink SDI keyer output OpenGL GPU-based image processing with 16-bit floating point linear per color component Shotcut 26.6.25 changelog highlights: Added basic support for OpenFX (OFX) video plugins. Added VST2 audio plugin support for third-party audio effects. Added Safe Mode to launch Shotcut without external plugins for easier crash recovery. Added an experimental plugin UI generator (--experimental) for supported filters and plugins. Added a new Noise Reduction audio filter powered by RNNoise. Added HDR export support. Added PQ HDR metadata options for HDR exports. Added the ability to view HDR previews in full-screen mode. Improved Vulkan display support on Linux. Fixed DeckLink and UltraStudio external monitor deadlocks. Fixed Opus audio export warnings related to frame_duration. Improved plugin discovery and compatibility for supported OpenFX and VST2 plugins. Expanded command-line options for testing experimental features. Improved overall application stability when using third-party plugins. Enhanced HDR editing and preview workflow. Included numerous bug fixes, performance optimizations, and general stability improvements throughout the application.[full release notes] Download: Shotcut 26.6.25 | Portable | ARM64 ~200.0 MB (Open Source) View: Shotcut Home Page | Other Operating Systems | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • I looked into a few echo devices to find they were riddled with adverts over time. No thanks ill stick to my homeassistant, smart plugs, smart bulbs and cameras that don't cost me a monthly fee and are cheaper to buy. No adverts also.
    • Brave Browser 1.91.180 is out.
    • Putin or Farage had nothing to do with me voting out. I did so because I got fed up of the E.U telling us what we could and could not do. Fed up with our country being run by a load of unelected Europrats. We never joined the E.U in the first place.
  • Recent Achievements

    • Week One Done
      Woland13 earned a badge
      Week One Done
    • One Month Later
      Woland13 earned a badge
      One Month Later
    • One Year In
      bernmeister earned a badge
      One Year In
    • Week One Done
      Scoobystu earned a badge
      Week One Done
    • Week One Done
      tuben earned a badge
      Week One Done
  • Popular Contributors

    1. 1
      +primortal
      503
    2. 2
      +Edouard
      229
    3. 3
      PsYcHoKiLLa
      163
    4. 4
      Steven P.
      77
    5. 5
      FloatingFatMan
      71
  • Tell a friend

    Love Neowin? Tell a friend!