Recommended Posts

Hi,

So I've got a HP DL160 G6 running with an HP SmartArray p410i 1GB super-capacitor RAM-based cache, and am using 3*15K RPM 73GB SAS drives in a RAID5 configuration and I have a single 500GB WD enterprise SATA drive connected too...

Now I know in comparison to the Dell PERC6 that the HP SA is a steaming pile of trash, it's much slower for reasons I've never been able to work out despite having a much better spec.

But this always gets me, I back up my VMs using the SSH server in ESXi and I have downtime of 50 minutes to transfer a 22GB VM, which is absolutely bloody rediculous (it's still not finished copying) and I'm just at a loss as to why. The 500GB drive isn't anything amazing, just a standard 7200 RPM drive but to transfer a VM at less than 7MBps is just... I'm speechless. I can transfer files faster on a 32 bit SCSI card faster than this.

 

Does anyone have a similar setup or any tips for this? (It's ESXi 5.1 and both file-systems are VMFS-5) I've got 4 more VMs to backup after this then apply some system updates and it's looking like it's going to take the whole day. I don't think it's a hardware speed problem, I'm thinking it's down to ###### poor drivers from HP for the p410i (hpaucli is [in comparison to dell's PERC utilities] a complete joke) or something up with ESXi but don't really know how I can go about test either or speeding it up.

Is the vmkern network on the same or a different physical port from the interface on your primary vSwitch?

 

I read that performance is awful unless this is separated (although I have never tried).

  On 24/01/2015 at 12:18, Fahim S. said:

Is the vmkern network on the same or a different physical port from the interface on your primary vSwitch?

 

I read that performance is awful unless this is separated (although I have never tried).

Ah, I don't mean I'm coping the data over SSH, I just mean I'm connected via SSH to do the file copying. It's going direct disk-to-disk on the same host.

At 11:58 I started copying a 10GB VM, 25 minutes later it's still not finished, so this copy speed is definitely slower than 7MBps.

How exactly are you doing this copy.. Are you going to the datastore and downloading the vm disk?

 

How is your vmkern - is it shared with another nic.. I noticed a huge increase in performance when broke out vmkern to its own port group on its own nic..

 

post-14624-0-74552400-1422101386.png

 

So here I started a download of vm - clicked go at 6:07:30..  Its downloading now, This is off a HP N40L with cheap nics added, the vmkern is using the built in nic I do believe.. If I look at my network performance for my pc I downloading the file too - getting pretty decent network util

 

post-14624-0-94754700-1422101722.png

 

Ok done...  looks like 20min

 

post-14624-0-40134400-1422102622.png

 

See the time created, and then last modified time..  So lets call it 34GB / 20 min = 1.7GB a min = 28MBps, which clearly is not full speed of my network..  I normally see double or triple that from the nas on the same esxi..  But it is inline with with how the vmkern works, etc..

 

edit:  So your dong disk to disk copy on your esxi host?  via cli command..  Let me test that with this same 34GB file..  I have a SSD datastore and the 250GB disk it came with as datastore as well..  BRB

 

Ok so started at 6:38:30 and so far its copied 3.8GB in 3 minutes.. 

so at 10 min mark bit over 12GB

 

/vmfs/volumes/54c39196-0f3ec6fc-3df2-001f29541714/test # ls -la
total 12049416
drwxr-xr-x    1 root     root           420 Jan 24 12:38 .
drwxr-xr-t    1 root     root          1400 Jan 24 12:37 ..
-rw-------    1 root     root     12343582720 Jan 24 12:48 w7x64-clean-flat.vmdk
/vmfs/volumes/54c39196-0f3ec6fc-3df2-001f29541714/test #

 

So I would have to say, seems like a bit slower than the download copy..  But that 250GB disk is pretty old crappy disk ;)

 

So at 20min, 24GB roughly looks like about 20MBps which yeah is like 3x what your seeing and this is just the controller that that comes with the N40L..

Not an answer to your problem but you could use ghettoVCB which is a free backup script for ESXi and works quite well. Bit fiddly to set up but once done it's fine. 

 

I have it scripted so I just log into the host and run a script to do the backup then once done I can copy the backup files without having to take down any of the servers.

I've now shut down all VMs except one (my W7 remote management VM) and I've taken a screenshot of it... Something really is not right here.

aNS6w1g.png

EDIT: Changed around the graph output (bit hard on a small VNC screen) and it's apparently reading at 6MBps from the main drive and writing to the backup drive at 15MBps... I can't understand how it's writing twice the data it's reading!

 

 

  On 24/01/2015 at 12:45, Depicus said:

Not an answer to your problem but you could use ghettoVCB which is a free backup script for ESXi and works quite well. Bit fiddly to set up but once done it's fine. 

 

I have it scripted so I just log into the host and run a script to do the backup then once done I can copy the backup files without having to take down any of the servers.

I can't do that as I've got snapshots disabled and have all changes written to the disk as they're performed.

Edited by n_K

Ok so it finished

 

/vmfs/volumes/54c39196-0f3ec6fc-3df2-001f29541714/test # stat w7x64-clean-flat.vmdk
  File: w7x64-clean-flat.vmdk
  Size: 34359738368     Blocks: 67108864   IO Block: 131072 regular file
Device: 831f0b1fc2871364h/9448282774282113892d  Inode: 4225796     Links: 1
Access: (0600/-rw-------)  Uid: (    0/    root)   Gid: (    0/    root)
Access: 2015-01-24 12:38:34.000000000
Modify: 2015-01-24 13:06:49.000000000
Change: 2015-01-24 13:06:49.000000000
 

 

So we got 28 min for 34GB, roughly 20MBps, which yeah is blowing you away on crappier hardware.... Hmmmmmm??

you could try dd command vs cp, doing a test now looks like 4.9GB in 3 minutes vs the 3.8 with the cp command, let me try uping the bs from 1M

 

edit:  Well using dd seems to get me the speeds I saw with download..  About 28MBps vs the 20 was seeing with cp.

 

edit2:  ok -- seems cp has really be depreciated for a while on esxi.. your suppose to use vmfsktools command..

 

http://www.vmware.com/pdf/esx_3p_scvcons.pdf

For performance and data placement reasons, do not use scp or cp; instead, use vmkfstools, the Virtual Machine Importer tool from VMware, or the SDK APIs to manipulate your virtual disks. You should see very significant performance improvements if you use the recommended tools.

 

So doing a copy of that same vm using

/vmfs/volumes/535605bc-d0c25a0d-7cf0-001f29541714/w7 # vmkfstools -i /vmfs/volumes/datastore0/w7/w7x64-clean.vmdk /vmfs/volumes/datastore1/test/test.vmdk
Destination disk format: VMFS zeroedthick
Cloning disk '/vmfs/volumes/datastore0/w7/w7x64-clean.vmdk'...
Clone: 100% done.
 

was done in 4.25 min or 133MBps

 

/vmfs/volumes/54c39196-0f3ec6fc-3df2-001f29541714/test # stat test.vmdk
  File: test.vmdk
  Size: 514             Blocks: 0          IO Block: 131072 regular file
Device: 831f0b1fc2871364h/9448282774282113892d  Inode: 8420100     Links: 1
Access: (0600/-rw-------)  Uid: (    0/    root)   Gid: (    0/    root)
Access: 2015-01-24 13:38:46.000000000
Modify: 2015-01-24 13:42:57.000000000
Change: 2015-01-24 13:42:57.000000000
 

 

post-14624-0-99362500-1422107393.png

 

Argh the dd is an annoying busybox version, just started running it with all the ibs and out set to 16MB and will see what happens with an 8GB file!

Did not know that about cp on ESXi, thanks budman! I'll see if DD increases the speed and if not will retry with that command, I'm assuming it doesn't bother copying the blank space and speeds up transfer that way, the VM I'm copying now is 90% utilised so it probably wouldn't save much time.

 

EDIT: OK no there is definitely something not right, 3Gbps link speeds between the SATA/SAS disks and the controller, 0.2GB copied in 30 seconds.

Edited by n_K

Dude see my edit.. Use vmkfstools -i src dst

 

My test shows a SCREAMING difference..   What you got to loose..  It sure can not be any slower than your dd or cp commands ;)

  On 24/01/2015 at 12:52, n_K said:

I can't do that as I've got snapshots disabled and have all changes written to the disk as they're performed.

 

Curios as to why you disabled snapshots.

Just tried on a 23GB disk after the 8GB DD finished budman;

/vmfs/volumes/508aa94d-fbcf15ba-0faf-68b599b49d30/Jan 24 2015/W7 # vmkfstools -i /vmfs/volumes/Main/Windows\ 7\ Pro
fessional-N\ x64/Windows\ 7\ Professional-N\ x64.vmdk /vmfs/volumes/Backup\ Disk/Jan\ 24\ 2015/W7/
Destination disk format: VMFS zeroedthick
Cloning disk '/vmfs/volumes/Main/Windows 7 Professional-N x64/Windows 7 Professional-N x64.vmdk'...
Failed to clone disk: The file already exists (39).
Ignore, I'm being dense and not putting in the filename!

 

  On 24/01/2015 at 14:11, Depicus said:

Curios as to why you disabled snapshots.

Uses space which I don't have that much of.

Yeah that is much better ;)  Should be a helpful thread for other people I think.. I don't normally move files between datastores

 

Now not sure on what your original was..  Was it thick, or thin?  Notice it defaults to thickzero'd -- so if was thin before, your backup isn't.  if you want to maintain thin you can do -d thin on the end.  But that took about double the time to copy..  But I would think even 10 minutes for you would be much better than what you were seeing.

Not so sure its really a performance booster doing that any more.. If on SSD datastore makes no difference for sure.. So your storage is local, is it VAAI ??  Do you see hardware acceleration when you look at your datastores?

 

There are lots of variables at play when it comes to performance - a we see in this example using a deprecated common way that many people would do can have huge performance implications.. Comes down to your requirements.  I for sure have my storage over provisioned for sure.. Small datastore..  And play with lots of vms, I don't see any reason to suck up all the space with zeros ;)

This topic is now closed to further replies.
  • Posts

    • Size 15. In the first week I managed to get a full week before having to recharge from 10%. I looked online and Samsung recommends recharging it when it gets to 20-30% to preserve the battery life. In the second week, started wearing my Galaxy Watch6 Classic again, because I read that it offsets sensors to the Watch, meaning the battery lasts even longer... and a week on (today) the ring was at 31% when I recharged it fully again, so a difference of over 20% in combination with the Watch. By the way I do not wear my Watch to bed, so it is only the Ring doing the sleep tracking (which is hit or miss tbh) it stops tracking for an hour or two in the night, which is really annoying. I had the same thing with the Watch, and I found it uncomfortable to have on in bed. I have been reading that the battery can start to go bad even after the first week so I am glad it isn't affecting me (yet).
    • Visual Studio gets even smarter with more AI models and billing updates by Usama Jawad Visual Studio and Visual Studio Code are among the most popular integrated development environments (IDEs) out there. The tools boast more than 50 million monthly active users, which isn't surprising considering their platform agnosticism, deep integration with the Microsoft ecosystem, and the power of GitHub Copilot. Now, Microsoft is looking to entice even more customers who are eager to use AI models to boost their productivity during the development process. In a blog post, Microsoft has stated that it has updated the AI models list available in Visual Studio to default to smarter options. For example, Copilot will now use GPT-4.1 rather than GPT-4o, since it offers better responses with faster performance. In addition, users can now select between the following models to enhance their coding experience based on their preferences: Claude Sonnet 4 Claude Opus 4 Claude Sonnet 3.5 Claude 3.7 (non-thinking and thinking) OpenAI o3 mini Gemini 2.0 Flash Gemini 2.5 Pro Microsoft has noted that your selected model will persist across your workflows, so if you're unsure about which model to leverage, you can refer to its documentation here. Furthermore, Visual Studio is making it easier to switch between models that are included in your plan through a prompt in the model selector. When it comes to billing updates, Microsoft has built a new Copilot Consumptions user experience that can be accessed by navigating to the Copilot badge present in the top-right corner of the IDE. As the name suggests, this panel shows your consumption in an easily digestible format. You can also click on Manage Plan, which will take you to the GitHub website. It is important to note that some models are request-heavy, and Visual Studio will now indicate this to you while you are selecting your model. If you exhaust your premium requests, you will shift to a standard model seamlessly. You should also keep in mind that the GitHub Copilot pricing plans have been updated, and the billing experience in Visual Studio does reflect them.
    • Indeed. It's apparently just a new search window that calls itself a "launcher"...yeehaw?! bleh.
    • Last I checked, their "support clock" runs for five years. So EOL at end of 2028 for this model? Roll your own looks better all the time. I do understand that's not for everyone. I think the least they could do is offer you six months of free cloud so you could migrate to new hardware when the time comes. Assuming you stick with them as your hardware vendor, of course.
    • Music Collection 3.9.1.1 by Razvan Serea Music Collection is a free tool to archive and manage your music library. Add CDs, LPs, tapes, or digital files manually or via the Internet. Retrieve album data by artist, title, barcode, catalog number, or CD scan. Auto-import metadata from audio files. Browse, sort, filter, export, import, and generate reports effortlessly. Music Collection features: The program creates the collection's database in a Microsoft Access format, so if you want later, you can use it, without the help of the program. The user can create as many as different collections wants. Accepts all kinds of musical media (cd, lp, dvd-a, audio files etc.). Specially customized to add and edit classical music albums. Retrieves data from the Internet, such as cd info, album cover, artist information, tracks, and the lyrics of each track etc. For every album the program saves all media contained, every medium tracks and the lyrics for every track. Displays albums using filters or the advanced search feature. Lists selected albums in a grid or using images (default setting). Presents all items contained in the album, in one page for an easy album overview. The details that are shown there are: album cover, album artists, notes, the tracks of each medium, the lyrics of each track and the duration of each one, as well as the total duration of the album. Exports album information to html file. Exports collection albums to html,txt,csv,excel files. Imports album information from text files exported by another program. Manages all program data, such as a list of singers, composers, etc. Manages artist information (biography, best albums). Prints all the data shown in each table.. Creates reports, which you can configure by your preference.. Manages album loans. Shows collection statistics. Searches for tracks and opens the album medium that contains them. Skinable. The user can select from 30 different skins. Multi-language support. Music Collection 3.9.1.1 changelog: Added: Show selected group item total duration. Added: Option to show only the checked albums. Added: Save the checked album property. Added: Play checked tracks. Fixed: Some minor bugs. Download: Music Collection 3.9.1.1 | 8.0 MB (Freeware) Download: Portable Music Collection 3.9.1.1 View: Music Collection Home page | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
  • Recent Achievements

    • Conversation Starter
      Kavin25 earned a badge
      Conversation Starter
    • One Month Later
      Leonard grant earned a badge
      One Month Later
    • Week One Done
      pcdoctorsnet earned a badge
      Week One Done
    • Rising Star
      Phillip0web went up a rank
      Rising Star
    • One Month Later
      Epaminombas earned a badge
      One Month Later
  • Popular Contributors

    1. 1
      +primortal
      528
    2. 2
      ATLien_0
      207
    3. 3
      +FloatingFatMan
      168
    4. 4
      Michael Scrip
      150
    5. 5
      snowy owl
      124
  • Tell a friend

    Love Neowin? Tell a friend!