Upload speeds are slow until computer is restarted


Recommended Posts

I am having a strange problem..for some reason when I go to upload something to say like mega, 1fichier, solidfiles, etc..pretty much any file host site my upload speeds only go to like 200 kb/sec but when I restart my computer and try again, my upload speed is maxed out, and regular speeds like I'm suppose to get, and I get 75 MB up..so usually its like 7.8 mb/sec and its fine for like a few hours, but then it does the same thing until I restart my computer. And when I run a speed test, that comes back fine (see below) so I don't know what is going on here. Can anyone help? and also my connection is hard wired

4648660552.png

 

I just ran another speed test at the same I was trying to upload something like you said, still getting around 200 kb/sec and speed tests are fine. and I checked in my router, there is no traffic shaping or traffic priority going on.

"75 MB up..so usually its like 7.8 mb/sec "

Well since you reversed Byte and bit here with your Big B's for bit and little b's for byte.. so are you seeing 200KByte or Kbits up because its a huge difference..

what I would like to see is a sniff when its real low and then a sniff when its working as normal.. Grab wireshark and do that.. you don't need to run it for the whole upload..  But run it for say 30 seconds on your slow upload and then 10 or so seconds on FAST upload.  PM me if you have any question on using wireshark its free and just sniff and then save the file and they might be large on your good speed upload..  But I can give you a place to upload them too so I can get them, etc.

Next time vs rebooting your computer just disable your interface and re enable it.  Are you wired or wireless?  With those speeds and that 4ms ping time I would for sure say wired, but want to make sure.  The speeds are doable with for sure with decent wireless but the ping time is really low for a wireless connection.

I'm wired directly to the router/modem. What do you want me to do exactly with wireshark? just let it run for 30 seconds with my good speed uploads, then again with the slow speed uploads?

I just tried what you said Budman..disabling it and re-enabling it(didn't know you could do that to fix a connection) and my upload speed was normal again when trying to upload something(see video I took below). Now I just gotta wait, because it's random when the upload speed at 200 kb/sec happens, so I'll post that second video when I try it again in a few hours

good upload speeds

Edited by Sharpstick68

I doubt that has anything to do with it.. But you find them in the advanced section of the driver.  Different nics, different drivers will have different options you can play with..  But I doubt its a setting like that you could tweak that is causing you a problem.

Offload is normally something you want ON!!  If your nic supports it, if doesn't and you have it on it just wouldn't do anything and still work.  What OS are you running btw?

 

 

 

driversettings.png

so has it happened again, have you taken any sniffs?  Does it happen on small files as well - what size of files are you sending.  If not too large you can just do the full sniff.  But if like 100MB then yeah the sniff would be 100MB in size ;)  Really curious to see the sniff when its bad!!

Yea it is still happening, but it is good to know that I can just disable and re-enable my network card without having to restart my computer to fix it(thanks BudMan). But it happens on files of all sizes, anywhere from 10 mb to 500 mb it's really strange. The next time it happens I will open up Wireshark and what should I look for..anything going to the file hosting site? which is solidfiles.com ?

also my network card is a Realtek® 8111E

and the network card drivers are up to date

Yeah like to see the transfer.. are you getting really all delays in the acks, is the window size not ramping up?  Are you having to retrans, etc. etc..

Kind of need to see a trace when your rocking full speed vs one when its ######.  Just because you restart your nic doesn't mean its really your end..  Maybe your sending to a different IP when its slow vs fast, etc.

 

grabbing now - but have to head to work in like 30 seconds.  Will look at today.

They are big most likely because you were downloading big files ;) 

edit:

Ok took a quick look, hope to get some more time later today.  But yeah your slow speeds make sense from the sniffs and your window size.  As you will see in the slow upload your largest size was 17462, less bytes on the wire in that frame..  While in your fast upload 62834 bytes in the frame.

Notice that in your fast upload you windows scaling is working scaled your window size by 4..  But in your slow upload scaling factor is -1?? I think this is because I missed the syn,ack for the start of this conversation so wireshark doesn't know what the scaling factor is suppose to be so just guesses.. (seeproblemwindowsizepic)  But clearly they are not the same.. So something not working in figuring out the scaling factor for the upload.  When you move large amounts of data over a wan you want a large window so you send more data in less number of packets.  So less back and forth acks while moving large amount of data.  In your slow upload your largest size is that 17k while in your fast upload your sending almost 63K bytes worth of data each time.

Now your sniffs are with 2 different file sizes or atleast showing that so not sure if you were sending the same file and just cut off the sniff or what haven't look that deep yet.  But in general if your window size is small to send say 10MB you need X number of conversations back and forth.. While each should take about the same time lets call it 30ms for example.. So if you can send that same 10MB in less interactions of send and ack, you can move that 10MB faster..

Clearly in your fast upload your sending more data per conversation then when your slow sending - huge difference between 17k and 63k.  So need to figure out why something is not working out right in your scaling?

What does this output for you?

C:\>netsh int tcp show global
Querying active state...

TCP Global Parameters
----------------------------------------------
Receive-Side Scaling State          : enabled
Chimney Offload State               : automatic
NetDMA State                        : enabled
Direct Cache Acess (DCA)            : enabled
Receive Window Auto-Tuning Level    : normal
Add-On Congestion Control Provider  : ctcp
ECN Capability                      : enabled
RFC 1323 Timestamps                 : disabled

Can you grab a sniff from the start of your sending so I can see the syn.ack and then wireshark should be able to correctly figure out the window size for the conversation.

 

 

 

 

quicklook.png

problemwindowsize.png

Edited by BudMan

Thanks for looking over the files BudMan, really appreciate it.

I did the first command line like you asked and this is what came back

  Quote

c:\>netsh int tcp show global
Querying active state...

TCP Global Parameters
----------------------------------------------
Receive-Side Scaling State          : enabled
Chimney Offload State               : automatic
NetDMA State                        : enabled
Direct Cache Acess (DCA)            : disabled
Receive Window Auto-Tuning Level    : normal
Add-On Congestion Control Provider  : none
ECN Capability                      : disabled
RFC 1323 Timestamps                 : disabled
** The above autotuninglevel setting is the result of Windows Scaling heuristics

overriding any local/policy configuration on at least one profile.


c:\>

 

And also here is the sniff file you asked for. I started sniffing before I even had the website up, then I tried uploading the file while it was sniffing, and these are my good speeds again, because like I said those slow upload speeds I get when attempting to upload happens at random times.. https://www.dropbox.com/s/6156l4s1cna46wo/fast-upload2.pcapng?dl=0

The good speed sniff had the syn,ack part.. What I would like to see bad speed with the syn,ack of the upload stream..

You might want to try turning these on

Add-On Congestion Control Provider  : ctcp
ECN Capability                      : enabled

netsh int tcp set global congestionprovider=ctcp

This can ramp up your window size quicker and could help in speed.  Can't hurt to turn it on.. And then do you upload tests, if you don't continue to see your good speeds or better than set it back to none.

edit: ok took a look at that next sniff and as you can see good window size sending large packets.. While your bad one was only sending 17K at the LARGEST...

decentwindowsize.thumb.png.8a1d8bbe30dd2

 

Edited by BudMan

I ran that command(as administrator) and it changed, then tried and it started out fast but then was transferring at about 2.1 MB/sec but then I closed out the site, stopped the sniff and tried again and my speeds were maxing out(you can take a look at the sniff file if you want, just let me know). But ok, I will try again some time later tonight or whenever, because like I said the slow speed is always at a random time, and I'm not uploading all the time, only when ever I feel like it, so the slow upload speeds can happen when ever..even at peak hours aka prime time 7 pm to 10/11 pm.

So if your uploading and your window size is small, then yes it will be slower if your window size is larger..  Without seeing the syn,ack of the conversation starting its impossible to see what and why they might not work out a large window size.

Ok you caught the syn so you see no windows scaling. This is why your slower is your sending smaller frames.. Remember before where you were sending 63k here your sending 17k  HUGE different for speed over a wan connection.

nowindowscaling.thumb.png.fb2e526b8ff4ed

Now just need to figure out WHY??  Let me look deeper and do some research on why windows scaling would not be used.  Did you change the option?  Also I don't like that yours has that * on it about windows scaling an heurstics - from my understanding what is reported is not always what is used..  I have to run out early this morning..  Will have more info later.

 

you enable ecn with from an elevated prompt.

C:\>netsh interface tcp set global ecncapability=enabled
Ok.

Can you show your globals again, are you still seeing the ** The above autotuninglevel setting is the result of Windows Scaling heuristics

So can you do this command

C:\>netsh interface tcp show heuristics
TCP Window Scaling heuristics Parameters
----------------------------------------------
Window Scaling heuristics         : disabled
Qualifying Destination Threshold  : 3
Profile type unknown              : normal
Profile type public               : normal
Profile type private              : normal
Profile type domain               : normal

Notice I have mine disabled..

Here you go BudMan

c:\>netsh interface tcp show heuristics
TCP Window Scaling heuristics Parameters
----------------------------------------------
Window Scaling heuristics         : enabled
Qualifying Destination Threshold  : 3
Profile type unknown              : normal
Profile type public               : normal
Profile type private              : restricted
Profile type domain               : normal


c:\>

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Par for the course. I asked a question a few days ago and was threatened to be reported. 😂
    • Ummmm Are you kidding? Do think these books being sold are disclosing they are AI written?
    • i'm just commenting because of this madness. you simply asked "what crowd" which i too am genuinely curious about, only to receive a response in the form of a link that directs to an analysis of the audited financial statements with the accompanying notes. then you say that the guy who wrote it is stupid, which whatever, that's not an argument being discussed atm, only to receive a response from Arceles saying "i don't deal with people whose first response is an ad homenim". jesus. this is like making a claim, and then saying "i don't deal with people who speak in a certain way or swear so i'm not gonna answer you hah!" (said in a nasaly voice, not trying to depict you Arceles). then focus on the argument instead of the explanation begins... "so what don't you like about the guy (lunduke)" followed by "he just likes to insult people" and the explanation for the "crowd" being referred to was never even established. so a request for an explanation about the crowd turned into an argument about "why do you think lunduke is an idiot". wowza.
    • Sony lays off 30% of staff from Days Gone developer Bend Studio by Pulasthi Ariyasinghe Another wave of layoffs has hit the game developer space, and this time, it's a first-party Sony studio that's been affected. Following a report by Bloomberg's Jason Schreier, Bend Studio has confirmed that it is letting go of "incredibly talented teammates" as it begins work on a new game project. "Today, we said goodbye to some incredibly talented teammates as we transition to our next project," said Bend Studio in a social media post today. "We're deeply thankful for their contributions as they've shaped who we are, and their impact will always be part of our story." Bend Studio is most well-known for its 2019-released open-world zombie adventure Days Gone, which even received a remaster just a few months ago. Prior to that, the studio had been responsible for the classic Syphon Filter series while also developing several PlayStation Portable and Vita games like Resistance: Retribution and Uncharted: Golden Abyss, respectively. "This is a difficult moment for our team, but we hold immense respect for everyone who got us here," the company added. "As we move forward, we remain committed to building the future of Bend Studio with creativity, passion, and innovation in the titles we craft." While Sony did not detail just how many staff have been affected by this latest decision, Jason Schreier revealed that 30% of the studio is being laid off. This amounts to around 40 people, according to the reporter. Earlier this year, Sony canceled two live service games that were in development at Bend Studio and Bluepoint Games. It was never revealed what this mystery game was supposed to be. "Bend and Bluepoint are highly accomplished teams who are valued members of the PlayStation Studios family," Sony said at the time. It's unclear if Bluepoint, which had been developing a God of War live service experience, will soon be hit by its own wave of layoffs too.
    • KataLib 4.5.3.0 by Razvan Serea KataLib is more than just a music player — it's a complete audio suite designed for music lovers and creators alike. It combines a powerful audio player, a flexible metadata editor, a capable audio converter, and a music library manager into one streamlined application. Core Features: Audio Player Enjoy seamless playback of virtually any audio format or even streaming video files. DJ Mode lets you mix tracks with manual or automatic crossfades. You can also load and save WinAmp-style playlists for quick access to your favorite sets. Audio Converter Convert between a wide range of audio formats effortlessly. Trim or normalize your output automatically, and even extract audio from streaming video sources. Ideal for preparing files for different devices or platforms. Metadata Editor View and edit ID3v2 tags and other metadata. Batch edit multiple files at once, and fetch missing information directly from the MusicBrainz database. You can also apply or update album art with ease. Music Library Manager Organize your entire audio collection, search across tracks instantly, and download cover images from the internet — or use your own custom artwork. KataLib makes it easy to keep your library tidy and enriched with useful info. Supported Formats: KataLib supports a wide range of both lossy and lossless audio formats: Input: OPUS, AAC, FLAC, M4A, MP3, MP4, MPC, APE, AIF, MKV, AVI, MOV, FLV, WEBM, Ogg Vorbis, WAV, WAVPack, WMA Output: OPUS, FLAC, M4A, MP3, Ogg Vorbis, WAV Under the hood, KataLib uses the trusted FFmpeg engine for audio conversion and media playback, ensuring compatibility with virtually all mainstream media formats. Download: KataLib 4.5.3.0 | 64.5 MB (Open Source) Links: KataLib Home Page | Github | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
  • Recent Achievements

    • First Post
      K Dorman earned a badge
      First Post
    • Reacting Well
      rshit earned a badge
      Reacting Well
    • Reacting Well
      Alan- earned a badge
      Reacting Well
    • Week One Done
      IAMFLUXX earned a badge
      Week One Done
    • One Month Later
      Æhund earned a badge
      One Month Later
  • Popular Contributors

    1. 1
      +primortal
      545
    2. 2
      ATLien_0
      268
    3. 3
      +FloatingFatMan
      207
    4. 4
      +Edouard
      201
    5. 5
      snowy owl
      139
  • Tell a friend

    Love Neowin? Tell a friend!