Remove 3M sticky adhesive from car phone rubber mount


Recommended Posts

I recently bought this: www.ebay.co.uk/itm/123910576823

 

I wanted to mount it, using the adhesive on the suction cup, to the dashboard.

 

However, as well as the fact it kept falling from the dashboard, it left an awful mark:

 

eb_adhesive1.thumb.jpg.345d5649103e5f5248f305b096f8e2db.jpg

 

Due to these facts, I got a full refund and went looking for the same mount (as the arm was perfect) but without the adhesive on the suction cup so I can use it on the windscreen.

 

Unfortunately, I can't find one without said adhesive so I've been looking at removing the adhesive on the mount I got the refund for.

 

Following random advice found via. Google, I soaked the cup in WD-40 for an hour and washed it away with soapy water but it's still extremely sticky. The WD-40 basically did not dissolve the adhesive in my case.

 

Can anyone suggest an alternative to WD-40, that's also suction cup-safe?

Elliot B.~

 

I'm not sure if they have this product  in the UK    but here in the states there is a product called  Goo Gone.. it GENERALLY will get rid of some very stubborn sticky   things  from cars  .. 

 

reference link for more info >>> https://googone.com/shop-categories#automotive

 

I KNOW for a fact here  in my home town  we have  small bottles of it  at  a store called Dollar Tree ( i happen to work there as a stocker/laborer)...    and yes everything literally is  1$   to buy .. 

 

Best of Luck 

~LoneWolf

 

 

3M products are very durable but they can be defeated. Get a little bit of dish soap, Sunlight or Dove, saturate the surface with it. Leave it for a bit and then take a hair dryer heat the adhesive and use more soapy water to remove the adhesive. Goo gone works on some things but not others. You need to be patient and exact as to how you hold the hair dryer kind of tilt it to the side as opposed to going directly on top of it. Best thing to use is like a small plaster knife, not a sharp one dull would be better. The adhesive will come off with no problem.

29 minutes ago, LoneWolfMage said:

Elliot B.~

 

I'm not sure if they have this product  in the UK    but here in the states there is a product called  Goo Gone.. it GENERALLY will get rid of some very stubborn sticky   things  from cars  .. 

 

reference link for more info >>> https://googone.com/shop-categories#automotive

 

I KNOW for a fact here  in my home town  we have  small bottles of it  at  a store called Dollar Tree ( i happen to work there as a stocker/laborer)...    and yes everything literally is  1$   to buy .. 

 

Best of Luck 

~LoneWolf

 

 

 

8 minutes ago, Human.Online said:

GooGone is very good at this sort of thing

Unfortunately, the cheapest I can find Goo Gone liquid adhesive remover on eBay in the UK is £6.90 for 2oz/57ml.

I've heard Goo Gone can leave an oily residue, too.

8 minutes ago, ddawson said:

3M products are very durable but they can be defeated. Get a little bit of dish soap, Sunlight or Dove, saturate the surface with it. Leave it for a bit and then take a hair dryer heat the adhesive and use more soapy water to remove the adhesive. Goo gone works on some things but not others. You need to be patient and exact as to how you hold the hair dryer kind of tilt it to the side as opposed to going directly on top of it. Best thing to use is like a small plaster knife, not a sharp one dull would be better. The adhesive will come off with no problem.

In the end, I bought some 99.99% isopropyl alcohol (50ml, £2.38).

2 hours ago, Elliot B. said:

I recently bought this: www.ebay.co.uk/itm/123910576823

 

I wanted to mount it, using the adhesive on the suction cup, to the dashboard.

 

However, as well as the fact it kept falling from the dashboard, it left an awful mark:

 

eb_adhesive1.thumb.jpg.345d5649103e5f5248f305b096f8e2db.jpg

 

Due to these facts, I got a full refund and went looking for the same mount (as the arm was perfect) but without the adhesive on the suction cup so I can use it on the windscreen.

 

Unfortunately, I can't find one without said adhesive so I've been looking at removing the adhesive on the mount I got the refund for.

 

Following random advice found via. Google, I soaked the cup in WD-40 for an hour and washed it away with soapy water but it's still extremely sticky. The WD-40 basically did not dissolve the adhesive in my case.

 

Can anyone suggest an alternative to WD-40, that's also suction cup-safe?

I would re-try the WD-40 but dont wash it with water. Take a dry towel first and rub off all the glue. Then once the glue is removed wash it...

14 minutes ago, SnoopZ said:

You missed where it says "£3.00 + £3.95 delivery" ;)

1 minute ago, Euphoria said:

I would re-try the WD-40 but dont wash it with water. Take a dry towel first and rub off all the glue. Then once the glue is removed wash it...

Sorry, that's what I did. Nothing rubbed off. So I washed it with water and soap and, once it had dried, it was still very sticky.

Just now, Elliot B. said:

You missed where it says "£3.00 + £3.95 delivery" ;)

Sorry, that's what I did. Nothing rubbed off. So I washed it with water and soap and, once it had dried, it was still very sticky.

Wow... thats weird... I've used it so many times to remove all kind of glue... from Velcro back glue to supper glue... 

32 minutes ago, Euphoria said:

Wow... thats weird... I've used it so many times to remove all kind of glue... from Velcro back glue to supper glue... 

you aren’t supposed to eat glue, so supper glue must be a typo 🙃

23 hours ago, Human.Online said:

GooGone is very good at this sort of thing

Agreed with you on that, it’s worked perfectly on anything I’ve ever used it on as far as removing adhesive residue. 
 

However from the picture the OP posted it looks like an indentation on the dashboard from the suction cup versus residue, I’m curious what kind of material the dashboard is made out of.

heat panel up with hairdryer

 

use only windshield stickers

Somewhat off topic but...

 

For car holders, I will ALWAYS use Brodit gear.  Not cheap, but for a valid reason - they are:

1) A holder for your phone with a ball-mount.  Nothing to connect to your car's panels, just the phone part.

2) A connector for your car - they assess a car's interior and find places where it can be moulded to clip-on without any damage.

 

Like I say, not cheap but utterly worth it!

5 minutes ago, Marujan said:

use only windshield stickers

Not always valid.  Some windshields are too far away - the car has a longer than (what I'd call average) dashboard.  Also they look crap!

 

You spend tens of thousands on a car, maybe a thousand or so on a phone, why spend ten on a crap holder.

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Turbo Pascal was my first real programming experience more than 30 years ago at university. I mostly taught myself from the included examples and help documentation, because the university only taught the basic syntax and philosophy of Pascal, without going deeply into Turbo Pascal’s advanced features. I still remember when I discovered that I could embed assembly language directly into Pascal code, call BIOS functions, manipulate screen memory, use mouse interrupts, and control peripherals from my programs. That opened huge doors for me. Programming back then felt really fun, direct, and close to the machine. What I loved about Pascal was its readability and the almost instant compile time. Turbo Pascal was an amazing environment, but unfortunately Turbo Pascal for Windows 3 did not feel like it fully carried that legacy forward. Later, Delphi got things back on the right track after the messy transition to TP for Windows. Sadly, Delphi suffered from years of uncertainty as it moved from Borland to CodeGear and then to Embarcadero. That instability made many developers lose confidence in it, even though Delphi itself remained a powerful and productive tool. I still work with Delphi from time to time, but I definitely miss the old days of Turbo Pascal.
    • I hope this encodes in to AV1 or AV2 as currently tiktok uses h265 and h264.
    • Qualcomm reportedly in talks to build custom video chips for TikTok parent ByteDance by Karthik Mudaliar Qualcomm is reportedly in advanced discussions to provide custom chip-design services to Chinese tech giant ByteDance, the same company behind TikTok. According to a report from Reuters, Qualcomm could be involved in designing custom silicon tailored for ByteDance's massive data-center workloads. If it goes through, the deal would make ByteDance one of Qualcomm's early anchor customers for its fastly growing custom chip-design division, For years, Qualcomm was the king of making smartphone processors and modems. The company has also been moving into the PC ecosystem and other formats such as on-device AI for Android XR headsets. However, this particular deal is about Qualcomm's custom Application-Specific Integrated Circuits (ASICs). For a platform like TikTok, ByteDance needs hardware that can help it ingest, process, and serve billions of short-form videos daily. Generalised hardware is no longer the most cost-effective and efficient route, which is why ByteDance is trying to develop custom Video Processing Units (VPUs). VPUs designed specifically for ByteDance’s algorithmic needs could drastically reduce data-center power consumption and improve encoding speeds at an unprecedented scale. The underlying tech behind these processors is actually from Qualcomm's recent acquisition of AlphaWave Semi, a high-speed connectivity specialist company. By combining AlphaWave’s high-bandwidth IP with Qualcomm’s architectural expertise, the company could begin mass production by the end of 2026, if the talks go through. All this also comes at a time when U.S.-China tech relations have dwindled. Escalating trade frictions between Washington and Beijing have severely impacted the export of high-end AI chips from U.S. firms like Nvidia, AMD, and Lam Research. Yet, the Qualcomm-ByteDance discussions show that U.S. tech companies are still actively seeking growth avenues and are open to doing business with China, where regulators still permit. Reuters notes that the outcome of this deal could be uncertain, and ByteDance might also seek partners other than Qualcomm. via Reuters | Image via DepositPhotos.com
  • Recent Achievements

    • One Year In
      OHI Accounting earned a badge
      One Year In
    • First Post
      Almohandis earned a badge
      First Post
    • Rookie
      DaviKar went up a rank
      Rookie
    • Dedicated
      HidekoYamamoto94 earned a badge
      Dedicated
    • One Month Later
      timbobit earned a badge
      One Month Later
  • Popular Contributors

    1. 1
      +primortal
      461
    2. 2
      +Edouard
      169
    3. 3
      PsYcHoKiLLa
      119
    4. 4
      Michael Scrip
      82
    5. 5
      Xenon
      69
  • Tell a friend

    Love Neowin? Tell a friend!