Considering a new build


Recommended Posts

I posted this on another site but figured I'd get some opinions here as well.

 

Currently running an i7-4790k with an RTX 2060 and looking to upgrade. Current uses are mainly gaming (and most titles are bit older), a bit of development and other production oriented tasks. Basically its a jack of all trades type of system. Thing is I like to buy for the longer term. Not future proofing, just a setup that will run well for 5 or 6 years. Looking to definitely upgrade to the new NVIDIA 3070 sometime later this year so its down to CPU/MB. Important note is that I do not overclock and will be sticking with mATX.

Option A is an i7 10700k in a Z490 (likely the ASUS Z490 PRIME Plus ) . I know, I can get by with a non-K variant but the clocks are lower so there is no point . The Z490 is simply because I'm a bit skeptical of the VRMs in the H470 boards. I also realize the i5 10600k is a worthy contender but for the longer term, the 8/16 core/thread count of the i7 seems a better bet.

Option B is a Ryzen 3900x in a B550 (likely the MSI B550M MAG Mortar).

Either system will be configured with 32gb of DDR4 3200 ram and a Sabrent 1TB Rocket (that only the AMD system can use to it's full potential). Case is a recycle of my current Case Labs Mercury S5. Cooling would be a Noctua NH-D15 chromax.Black (Intel) or the stock Wraith Prism (AMD).

These two systems will end up being very close in price so that makes it more difficult. Gaming goes to Intel, everything else to AMD. If I did any video production or streaming  it would be a no brainer but I don't so its a draw.

Any thoughts?

Link to comment
https://www.neowin.net/forum/topic/1399432-considering-a-new-build/
Share on other sites

From what I see, they aren't expected until early October - maybe. The problem then becomes cost as the 4000 series is expected to be priced at release in line with 3000 series release pricing.  That would price the 3900x equivalent almost 150.00 bucks higher than the current i7 price and I've not seen any evidence (or even strong inference) that AMD is going to top Intel at single thread and gaming with the next gen to the extent to justify the price difference. Depending on vendor, that will nearly be the difference between an NVIDIA 3070 and a 3080. Right now with both the i7 and the 3900x below 400 (and pricing favors the i7 right now) things are muddy but at 379.00 (i7) vs 499.00 (AMD) the only thing waiting may do is decidedly push me to stay with Intel. 

 

Look, I can wait or I can buy now. Waiting for the 'next gen' of these types of things is a never ending process that leads to analysis paralysis. There is always something 'better' being released in just a couple of months.   In my case I'd like to make this purchase in the next 7 to 14 days so it boils down to the original two options. 

 

I know you prefer AMD so tell me why? Being honest, I'd normally just go Intel and call it a day. This time around, I'm looking to give team red a good look but honestly my only real justification for considering them is that I may benefit from their core/multithreading performance at some point in the next 5 years. For what I normally do, they do NOT have a clear advantage today but I'm being open to considering them, strongly so for no other reason than to not to reward Intel for excelling in mediocracy. 

I would personally go with the AMD build. 

 

1) You'll be gaming and potentially doing *other* things.

2) It seems that that the Intel gaming advantage starts to taper off with higher resolutions (obviously depends on title/gaming engine).  I doubt you're gaming at 1080p and contemplating upgrading a very capable 2060 to a 3070.

 

Though at the end of the day ... both the Intel and AMD builds will "run well for 5 or 6 years."

Honestly IMHO, going AMD is going to be the better way for you, you get better performance for your buck, and with the money you save going the AMD route will allow you to get the 3000 series Nvida GPU. Also, like @Jim K said, both builds will give you 5 or more years, and I have learned that there truly is no such thing as 'future proofing' when it comes to computer hardware, the market has far too many unknowns to make even an educated guess as to what will happen, so it really comes down to 1) How much you are willing to spend 2) What you are going to use the system for, and 3) Do you want to have the best of the best hardware right now, or can you get something slightly less? Answering those 3 questions should give you a baseline for your new build.

Even if you don't go for the 4000 series it may still be advantageous to wait for them to release in a couple months. once they release there should be more discounts/sales on the 3000 series which is still an excellent lineup and IMO better than what Intel has to offer at the moment.

2 hours ago, Zag L. said:

From what I see, they aren't expected until early October - maybe. The problem then becomes cost as the 4000 series is expected to be priced at release in line with 3000 series release pricing.  That would price the 3900x equivalent almost 150.00 bucks higher than the current i7 price and I've not seen any evidence (or even strong inference) that AMD is going to top Intel at single thread and gaming with the next gen to the extent to justify the price difference. Depending on vendor, that will nearly be the difference between an NVIDIA 3070 and a 3080. Right now with both the i7 and the 3900x below 400 (and pricing favors the i7 right now) things are muddy but at 379.00 (i7) vs 499.00 (AMD) the only thing waiting may do is decidedly push me to stay with Intel. 

AMD is getting rid of the CCX (core complex) in 4th gen Ryzen. There should make a significant difference in gaming performance.

 

...and of cause, there is the matter of increased IPC, in general

 

1 hour ago, jnelsoninjax said:

Honestly IMHO, going AMD is going to be the better way for you, you get better performance for your buck, and with the money you save going the AMD route will allow you to get the 3000 series Nvida GPU. Also, like @Jim K said, both builds will give you 5 or more years, and I have learned that there truly is no such thing as 'future proofing' when it comes to computer hardware, the market has far too many unknowns to make even an educated guess as to what will happen, so it really comes down to 1) How much you are willing to spend 2) What you are going to use the system for, and 3) Do you want to have the best of the best hardware right now, or can you get something slightly less? Answering those 3 questions should give you a baseline for your new build.

I don't agree with that.

 

We already have a general timeline for the products.

 

We already know that the GeForce RTX 3000 series is coming soon.

 

Likewise, we know that 4th gen Ryzen processors are coming soon.

 

We also know that Intel just released 10th gen Core processors.

 

Nobody is saying: "Wait a year or two."

 

2 hours ago, Zag L. said:

I know you prefer AMD so tell me why? Being honest, I'd normally just go Intel and call it a day. This time around, I'm looking to give team red a good look but honestly my only real justification for considering them is that I may benefit from their core/multithreading performance at some point in the next 5 years. For what I normally do, they do NOT have a clear advantage today but I'm being open to considering them, strongly so for no other reason than to not to reward Intel for excelling in mediocracy. 

Well, I was going to say power consumption.

 

Core i7-10900K (8-cores/16-threads) uses more power than a Ryzen 9 3950X (16-cores/32-threads).

 

Now, at this point, you may say, "so what", but remember, all that heat is being dump into your room.

 

Furthermore, you are going to have to invest in a big cooler since Intel didn't include one (AMD includes the Wraith Prism).

 

untitled-3.png

3 hours ago, jnelsoninjax said:

Honestly IMHO, going AMD is going to be the better way for you, you get better performance for your buck, and with the money you save going the AMD route will allow you to get the 3000 series Nvida GPU. Also, like @Jim K said, both builds will give you 5 or more years, and I have learned that there truly is no such thing as 'future proofing' when it comes to computer hardware, the market has far too many unknowns to make even an educated guess as to what will happen, so it really comes down to 1) How much you are willing to spend 2) What you are going to use the system for, and 3) Do you want to have the best of the best hardware right now, or can you get something slightly less? Answering those 3 questions should give you a baseline for your new build.

Not looking to 'future proof'. It doesn't exist. Just looking for something reasonably high end that will carry me to retirement.  As for budget, if I'm considering these class processors w/32 Gb RAM and a 3070, I'd say my budget is ample. The original post outlined my usage. I am gaming heavy (albeit older games) with a little mix of productivity work. Each system has its plusses and minuses and at the current prices all systems are competitively priced. 

 

3 hours ago, Brandon H said:

Even if you don't go for the 4000 series it may still be advantageous to wait for them to release in a couple months. once they release there should be more discounts/sales on the 3000 series which is still an excellent lineup and IMO better than what Intel has to offer at the moment.

I really thought about that myself but my concern was what will availability be of 3900x SKUs as we get closer to the eventual 4000 release. The 3900x is already a very attractive option at $399 and while it could move a bit lower, so could available stock as vendors make room for 4000s.  

 

2 hours ago, Mockingbird said:

Well, I was going to say power consumption.

 

Core i7-10900K (8-cores/16-threads) uses more power than a Ryzen 9 3950X (16-cores/32-threads).

 

Now, at this point, you may say, "so what", but remember, all that heat is being dump into your room.

 

Furthermore, you are going to have to invest in a big cooler since Intel didn't include one (AMD includes the Wraith Prism).

 

 

If I were concerned about overall power consumption I'd never consider Intel in the first place. I keep my residence at 74F (23C) in the summer and 68F (20C) in the winter. I live in a hot climate and have no issue cranking down the AC. Dumping a few more BTU's into that room isn't a concern to me from both temperature or cost.  I use over 2100 KWh a month in the summer so the difference between the two systems for the 10 hours a week the system is in use is irrelevant.    As for the cooler, that's the only thing keeping the prices in line actually. As I noted I'm planning for the  Noctua for the Intel build and relying on the wraith for the AMD. That cost is already factored in. If for some reason the wraith isn't going to  cut it, well that's another hundred bucks I need to move to the AMD column.

 

End of the day, I could easily see myself going down to Microcenter today and grabbing the AMD  components. In fact, its a rather low cost  proposition right now and I'm very much inclined to commit. With the CPU at $399.99 plus a MSI B550M MAG Mortar at $139.99 I walk out at about $585.00.  Could I wait a month or two. Sure I could but at the risk of either not finding a 3900x OR the 4000 series equivalent costing 100 bucks more. I could also just pick up an i5 10600K in that same Z490 board, tweak it a bit and have a 6 core system that has the same gaming performance as the i7 and in some cases the i9 for a bit less (even with the cost of the Noctua factored in). 

3 hours ago, Zag L. said:

Made the decision, I'm going team red. Just need to figure out when to buy. Thanks to everyone for their insight. In tge end it was very appreciated.

Beware of Newegg. They have some serious shipping issues coming out of California as of last month. 
 

 

3 minutes ago, adrynalyne said:

Beware of Newegg. They have some serious shipping issues coming out of California as of last month.

Never heard of that.. Every company, even Amazon has trouble from time to time...

 

25 minutes ago, Mindovermaster said:

Never heard of that.. Every company, even Amazon has trouble from time to time...

 

Plenty of others have also mentioned it if you take a look on reddit and they admitted it to me themselves when I reported a lost package worth 3.3k last month.

 

Useful post, did you have something worthwhile to add? Or are you just posting to downplay advice I have given someone so that they can avoid trouble?

2 minutes ago, adrynalyne said:

Plenty of others have also mentioned it if you take a look on reddit and they admitted it to me themselves when I reported a lost package worth 3.3k last month.

 

Useful post.

I'll use Reddit the day they unlock my 3 accounts I made. I just hate their poison.

 

I rarely get anything from their California plant. They usually ship from Indiana, I think it is... Or close to there. Huh...

I'd wait 2-3 months for sure. Next nVidia and AMD cards are coming out soon and the new Ryzen cpus too. The computer you'll buy today will like already be outdated in 2 months. I'd definitely go for a Ryzen 4xxx cpu with a b550 motherboard when they will be out later this fall. Probably a nVidia RTX 3xxx card.

 

If you decide not to wait i would definitely go for a b550 motherboard for PCI-E 4. Not really useful now outside of pci-e 4 nvme drives but you never know if you plan to keep as long as your current build it could very well be relevant before you upgrade.

 

Hardware Unboxed made a very good roundup of all the b550 motherboards lately.

Edited by LaP
17 minutes ago, LaP said:

I'd wait 2-3 months for sure. Next nVidia and AMD cards are coming out soon and the new Ryzen cpus too. The computer you'll buy today will like already be outdated in 2 months. I'd definitely go for a Ryzen 4xxx cpu with a b550 motherboard when they will be out later this fall. Probably a nVidia RTX 3xxx card.

 

If you decide not to wait i would definitely go for a b550 motherboard for PCI-E 4. Not really useful now outside of pci-e 4 nvme drives but you never know if you plan to keep as long as your current build it could very well be relevant before you upgrade.

 

Hardware Unboxed made a very good roundup of all the b550 motherboards lately.

I’d go x570 over b550. 
 

Well not would, did. 

14 hours ago, LaP said:

I'd wait 2-3 months for sure. Next nVidia and AMD cards are coming out soon and the new Ryzen cpus too. The computer you'll buy today will like already be outdated in 2 months. I'd definitely go for a Ryzen 4xxx cpu with a b550 motherboard when they will be out later this fall. Probably a nVidia RTX 3xxx card.

 

If you decide not to wait i would definitely go for a b550 motherboard for PCI-E 4. Not really useful now outside of pci-e 4 nvme drives but you never know if you plan to keep as long as your current build it could very well be relevant before you upgrade.

 

Hardware Unboxed made a very good roundup of all the b550 motherboards lately.

As stated in the original post, the motherboard choice is the MSI B550M MAG Mortar to take advantage of the Sabrent Rocket NVME PCIE4 SSD and the Ampere 3070 (which may release Monday). Only thing I don't like about this board is the lack of USB on the rear I/O.  Waiting for the 4000 series will certainly increase the build cost with an unknown level of benefit. Getting an AM4 socket will let me drop in a 4000 series a year or two down the road if my needs change and would benefit from what the 4000 series offer. This is actually one of the more prominent reasons for AMD over Intel for me. The 1200 socket is at the end of the road. 

14 hours ago, adrynalyne said:

I’d go x570 over b550. 
 

Well not would, did. 

@adrynalyne why do you say that? I just don't see any advantage for my usage on any of the very few x570s I could find.  I did mention in the OP that the case is a Caselabs Mercury S5 so I'm limited to mATX or mini ITX and these form factors appear to have almost no x570 support. I did look at the ASUS B550-I ROG Strix but as a mini ITX, it only has one full length PCIE slot and one m.2 slot.  Spending $100 more for a motherboard that offers no apparent advantages doesn't make a compelling argument for me to consider. That said, convince me. Everyone in this thread has  stated why they suggested what they did and as a result, I'll be moving away from Intel for the first time since my first 8088 PC clone. What advantage am I missing out on by choosing of the handful of x570 

11 hours ago, Zag L. said:

As stated in the original post, the motherboard choice is the MSI B550M MAG Mortar to take advantage of the Sabrent Rocket NVME PCIE4 SSD and the Ampere 3070 (which may release Monday). Only thing I don't like about this board is the lack of USB on the rear I/O.  Waiting for the 4000 series will certainly increase the build cost with an unknown level of benefit. Getting an AM4 socket will let me drop in a 4000 series a year or two down the road if my needs change and would benefit from what the 4000 series offer. This is actually one of the more prominent reasons for AMD over Intel for me. The 1200 socket is at the end of the road. 

@adrynalyne why do you say that? I just don't see any advantage for my usage on any of the very few x570s I could find.  I did mention in the OP that the case is a Caselabs Mercury S5 so I'm limited to mATX or mini ITX and these form factors appear to have almost no x570 support. I did look at the ASUS B550-I ROG Strix but as a mini ITX, it only has one full length PCIE slot and one m.2 slot.  Spending $100 more for a motherboard that offers no apparent advantages doesn't make a compelling argument for me to consider. That said, convince me. Everyone in this thread has  stated why they suggested what they did and as a result, I'll be moving away from Intel for the first time since my first 8088 PC clone. What advantage am I missing out on by choosing of the handful of x570 

More PCI express lanes as well as more (faster) USB port support than B550. If you don’t have a use for those then disregard my thoughts on it. 🙂

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Posts

    • PDF-XChange Editor 11.0.1.0 by Razvan Serea PDF-XChange Editor is a comprehensive PDF editor that allows you to create, view, edit, annotate, and digitally sign PDF documents with ease. With advanced features like OCR, document security, and PDF optimization, PDF-XChange Editor is a powerful tool for both personal and professional use. Whether you need to edit text, images, or links, or add comments, stamps, or watermarks, PDF-XChange Editor provides all the necessary tools to make your PDFs look perfect. Additionally, it supports a wide range of file formats, including PDF, XPS, and DOCX, making it easy to convert and share your documents. PDF-XChange Editor key features: Edit text and images in PDF documents Add and remove pages from PDF files Annotate and markup PDFs with comments, highlights, and stamps Use OCR to convert scanned documents into searchable text Create and fill out PDF forms Sign and certify PDF documents digitally Add and edit hyperlinks within PDFs Extract text and images from PDF files Batch process multiple PDF files at once Customize the interface to your preferences Work with multiple documents in tabs Convert PDFs to other formats such as Word, Excel, and HTML Use advanced redaction tools to permanently remove sensitive information Add customizable headers and footers to PDFs Merge multiple PDF documents into a single file Split PDF documents into multiple files Add watermarks to PDF documents Use the measurement tools to calculate distances and areas in PDFs ....and much more PDF-XChange Editor 11.0.1.0 changelog: Fixed a crash in the new Open/Save dialog box when creating a new folder in an unavailable network path. (49552) Fixed a rare/infrequent crash on some dynamic XFA forms after changing their field values. [installer] Fixed an issue where shortcuts were lost during an upgrade from the previous version. [installer] Fixed an issue preventing migration of serial keys during updates from version 10. Fixed the issues with the shell context menu after installation of version 11. Fixed the issue with filtering comments. (49478) Fixed the issue that caused "Error [IO subsystem]: Invalid access mode." when converting PDFs to MS Office formats. Fixed an issue with the context menu position on some multi-monitor systems. (48467) Fixed an issue with handling complex custom file filters, displayed by JS, in the new Open/Save Files dialog box. (49486) Fixed several issues with the new 'Select Folder' dialog box. (49505) Fixed an issue with the new custom 'Open File' dialog box when using double-click to open it. (49498) Fixed an 'infinite' loop/proliferation in the 'Open Files' and 'Manage Places' dialog boxes. (49526) Fixed an issue with handling the mouse wheel inside the document "Find" box. (49539) Fixed an incorrect behaviour in the 'Go back (Alt+Left)' button in the new Open/Save Files dialog box. (49510) Fixed an issue with the shortcut keys (Alt+Left/Right) after navigating via breadcrumb paths in the new Open/Save Files dialog box. (49554) [installer] Fixed an issue with redrawing the progress text in the EXE installers. Fixed the issue where a mouse click outside of the polyline/polygon context menu during annotation creation would cancel the annotation. (49475) We switched back to using the system Open/Save/SelectFolder dialog box by default, instead of using the new one, because some popular features such as the QuickAccess/Recent items are missing in the new version. These will be added in a future release. Replaced the 'Extension' column in the new Open/Save File dialog box with a more user-friendly 'Type' column. Also fixed some issues when handling the 'Show file extension' option. (49497) Added the ability to authenticate local network shares in the new Open/Save Files dialog box. (49557) Improved the handling of dates after 01.01.2030 in XFA files - now such dates are stored properly when set via the dropdown widget. Flags NoZoom and NoRotate are now respected for only a limited subset of annotations. Download: PDF-XChange Editor (64-bit) | Portable ~300.0 MB (Shareware) Download: PDF-XChange Editor (32-bit) | Portable ~200.0 MB Download: PDF-XChange ARM64 | 276.0 MB Download: PDF-XChange Portable @PortableApps.com | 97.0 MB View: PDF-XChange Editor Website | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • Still 3x what it should cost. So, it seems the trick is to increase price by 6x so that a reduction in price back to 4x looks like a steal. "You savvy shoppers win again!" I'm glad I'm not in a desperate spot to actually even need this overpriced crap. Hopefully, it comes back down by the time for when (or if) I ever do.
    • Although AI is great and has it's use cases they likely have massively overhyped it and it has not delivered as per their expectations. I fully expect them to start saying the same things again when it does get to a certain level of intelligence!
    • Microsoft wants to end printer driver headaches with Windows Ready Print by Usama Jawad A few days ago, Microsoft released Windows 11 Experimental build 26300.8553, bringing a ton of enhancements such as Start menu customization, search improvements, Taskbar polish, and other minor UI tweaks. Another relatively major enhancement snuck deep within the change log was related to upgrades to the Windows printing experience. Now, Microsoft has shared more details about these benefits. For starters, Microsoft has renamed its Modern Print Platform to Windows Ready Print. The company believes that this name highlights its shift in strategy, which now focuses on modernizing, securing, and streamlining the printing experience for Windows devices. Some of the upgrades present in Windows Ready Print have already been seeded to customers and partners. This includes ending support for third-party printer drivers via Windows Update and transitioning towards the Internet Printing Protocol (IPP) and the native Windows IPP printer driver. In line with these changes, new printer installations will default to Windows Ready Print on eligible devices starting from July 2026. However, Microsoft recognizes that not all environments will be able to migrate to this platform immediately, so it will allow users to choose between installing the printer via Windows Ready Print or the traditional OEM process. Users will be able to toggle this configuration through Settings > Bluetooth & Devices > Printers & Scanners > Printer preferences. This control applies only to new printer installations, and its functionality can also be modified via Group Policy as follows: Launch Group Policy Editor Navigate to Local Computer Policy -> Administrative Templates -> Printers Find and select 'Configure Windows Ready Print driver ranking' -> double click to open it Select 'Enabled' (if you wish to enable Windows Ready Print driver selection) or 'Disabled' (if you wish to explicitly disable Windows Ready Print driver selection). Select Apply Select OK Similarly, if you set up Windows protected print mode through the same setting in Windows 11, it will also default to using Windows Ready Print exclusively. Microsoft hopes that these improvements will help eradicate dependency on OEM-specific driver installation processes and simplify printer installations. We'll likely find out more about other tangible benefits in the coming months.
  • Recent Achievements

    • One Month Later
      johnjacobb40 earned a badge
      One Month Later
    • One Year In
      Primer1st earned a badge
      One Year In
    • Experienced
      JayZJay went up a rank
      Experienced
    • Reacting Well
      Sir_Timbit earned a badge
      Reacting Well
    • Week One Done
      rubentuben8 earned a badge
      Week One Done
  • Popular Contributors

    1. 1
      +primortal
      513
    2. 2
      PsYcHoKiLLa
      231
    3. 3
      +Edouard
      138
    4. 4
      ATLien_0
      87
    5. 5
      Steven P.
      81
  • Tell a friend

    Love Neowin? Tell a friend!