Computer crashed, can't get into Windows no more..


Recommended Posts

So I was playing a game last night and my computer froze, I had to reset it by holding the power button..after I did that I was greeted with a blue screen (see below) and I said ok. Next thing, I see something that says MSI starting automatic repair (relating to windows I guess) let it do that for about 5 mins and it never did boot into windows so I reset the system again and powered it back on, and also before that I went into the bios to try and see if I can get into recovery/safe mode from there but couldn't find anything. So now, when I try powering my system on, the fans come on, start spinning and rgb goes on and everything, but there is a red light on the motherboard and it won't go away and also I get no video signal from my monitor either. So far I've tried flashing my bios (see specs below) and clearing the cmos, and still nothing.

My system specs are...

Intel i7-13700K CPU

MSI Z790 MPG Edge WiFi DDR4 Motherboard

Corsair Vengeance RGB RT 32GB (2 x 16GB) DDR4-3600 PC4-28800 RAM

EVGA RTX 3070 FTW3 Graphics Card

Corsair RMx Series RM1000x 1000 Watt PSU

Corsair iCUE H150i ELITE CAPELLIX 360mm RGB Water Cooling Kit

Everything was working fine before this happened. I did update my motherboard bios a few weeks back because I finally started having problems with games crashing, due to the 13/14th gen intel cpu's problems thats been happening, something to do with the microcode or whatever it is. I had this system built November 2022 by microcenter, and it's just so frustrating to learn about these problems intel cpu chips are having, it makes me not want to trust intel any more because I don't know how recently it started happening but as far as I know it affects 13 and 14th gen chips. Anyway, sorry for the rant..I just don't know what else to try before bringing it to microcenter so they dcan diagnose the issue.

 

 

20250106_211749.jpg

  On 07/01/2025 at 11:38, Sharpstick68 said:

it's just so frustrating to learn about these problems intel cpu chips are having, it makes me not want to trust intel any more

Expand  

it is quite possible that the problem here is un-related to the Intel CPU you have.

  On 07/01/2025 at 11:38, Sharpstick68 said:

there is a red light on the motherboard

Expand  

try re-seating the components especially the CPU if you haven't already

  On 07/01/2025 at 11:38, Sharpstick68 said:

so I reset the system again

Expand  

Do you mean you performed a system reset as in a Windows re-install choosing to keep personal files and programs or you just did a hard shutdown by holding the power button until it turned off?

 

I am assuming you just held the power button down as mentioned earlier in your post but want to make sure.

 

Lets see if you can boot from a linux USB. If so, you can use it to backup your important files.

On another PC: https://ubuntu.com/tutorials/create-a-usb-stick-on-windows#1-overview

Edited by xrobwx71
  • Like 2

Trying a live USB is a good start.

Also, when you power on the computer I think you can get into the advanced options - which is where safe mode is located - by powering off your computer when you see the Windows logo. You need to do that three times, then the automatic repair will appear on the next boot, followed by the option to go to advanced options.

A quick search shows that the most common reason for the error message is a driver issue, so booting into safe mode should at least get you access to the system.

  On 07/01/2025 at 12:40, xrobwx71 said:

Do you mean you performed a system reset as in a Windows re-install choosing to keep personal files and programs or you just did a hard shutdown by holding the power button until it turned off?

 

I am assuming you just held the power button down as mentioned earlier in your post but want to make sure.

 

Lets see if you can boot from a linux USB. If so, you can use it to backup your important files.

On another PC: https://ubuntu.com/tutorials/create-a-usb-stick-on-windows#1-overview

Expand  

Sorry I should have worded that better. When I said I performed a system reset, I meant as in I held the power button down on the case so the system shuts off, that is what I meant.

Based on the manual for your motherboard, it looks like the red LED indicates an issue with the CPU.  As some of the others have said, try removing the CPU and cooler and reseating them.  Ideally you'd want to put fresh thermal paste on, but you can do that later if you get it working.

You could also try removing a stick of RAM and seeing if it'll boot with 1 stick.  Try with each stick individually to see if maybe one of them is bad.
Also try removing and reconnecting all the power supply cables.  Maybe one wasn't seated correctly and isn't supplying sufficient power.

You could try a live USB linux distro just to see if the PC will at least function.  That would then tell you if it's a hardware issue or a Windows install issue.
And if all of these things fail, then maybe your CPU did indeed fail.

image.png.b5fb533522c5f43165f6106c9307ebe7.png

  On 07/01/2025 at 18:47, Astra.Xtreme said:

Based on the manual for your motherboard, it looks like the red LED indicates an issue with the CPU.  As some of the others have said, try removing the CPU and cooler and reseating them.  Ideally you'd want to put fresh thermal paste on, but you can do that later if you get it working.

You could also try removing a stick of RAM and seeing if it'll boot with 1 stick.  Try with each stick individually to see if maybe one of them is bad.
Also try removing and reconnecting all the power supply cables.  Maybe one wasn't seated correctly and isn't supplying sufficient power.

You could try a live USB linux distro just to see if the PC will at least function.  That would then tell you if it's a hardware issue or a Windows install issue.
And if all of these things fail, then maybe your CPU did indeed fail.

image.png.b5fb533522c5f43165f6106c9307ebe7.png

Expand  

I will try what you are suggesting, but just a few questions for clarification

Should I leave my AIO cooler off and booting my system up? or should I reseat the cpu and put the cooler back on before testing again..

I also want to try removing 1 stick of ram to see if the memory could be the problem also

  On 07/01/2025 at 21:46, Sharpstick68 said:

I will try what you are suggesting, but just a few questions for clarification

Should I leave my AIO cooler off and booting my system up? or should I reseat the cpu and put the cooler back on before testing again..

I also want to try removing 1 stick of ram to see if the memory could be the problem also

Expand  

No. You should start from the basics and work up.

Does a live USB key work?

Can you access safe mode?

Have you switched off the cooler?

Have you reseated the standard devices that possibly cause the error code?

  On 07/01/2025 at 21:46, Sharpstick68 said:

I will try what you are suggesting, but just a few questions for clarification

Should I leave my AIO cooler off and booting my system up? or should I reseat the cpu and put the cooler back on before testing again..

I also want to try removing 1 stick of ram to see if the memory could be the problem also

Expand  

You always want to have the cooler completely installed.  Without the cooler, the CPU is going to overheat extremely fast.  I guess you could run it without the cooler for a few seconds just to see if the PC will get further in the boot process, but definitely don't run it for long that way.

  On 07/01/2025 at 21:55, Nick H. said:

No. You should start from the basics and work up.

Does a live USB key work?

Can you access safe mode?

Have you switched off the cooler?

Have you reseated the standard devices that possibly cause the error code?

Expand  

No a live USB key doesn't work

No I can not access safe mode

What do you mean when you say "Have I switched off the cooler?"

No can you explain what that may be? I have already checked to make sure the power cables are all firmly and tightly plugged in, all cables appear to be fully and securely in place

  On 07/01/2025 at 22:03, Sharpstick68 said:

No a live USB key doesn't work

No I can not access safe mode

What do you mean when you say "Have I switched off the cooler?"

No can you explain what that may be? I have already checked to make sure the power cables are all firmly and tightly plugged in, all cables appear to be fully and securely in place

Expand  

A live USB doesn't work? Ok, that's an issue. That probably means that the problem is with the hardware rather than with Windows.

If you can't access safe mode via the instructions I provided...well, given your above response I'm ok with that, since the problem isn't with Windows.

"Switched off" or in any way disconnecting the cooling system from the rest of the system. We're working towards the idea that the issue is hardware based, so disconnecting the cooler would be a good start. It's not necessary, it's just nice to have.

And to the last point, since you'll be opening the box and disconnecting the cooling system, you may as well take out the RAM and SSD (or HDD) and plug them back in again (i.e. "reseating"). There's a reason that there is the stupid idea of "have you tried turning it off and on again?" Same applies to hardware. Take it out, put it back in. And if you can, try a different location.

  On 07/01/2025 at 17:24, Sharpstick68 said:

When I said I performed a system reset, I meant as in I held the power button down on the case so the system shuts off, that is what I meant.

Expand  

Heh.. yeah, affectionately referred to as a "hard" reset.

 

That red CPU light may and may not indicate the CPU... as I have an MSI board. Last time I cleaned it, I left the CPU in.. but removed all the rest of the components on the board.

When I had it all back together, she wouldn't boot at all.. and all I had was that red CPU light.

 

Found out there was a tiny wire from the CPU cooler that prevented a stick of RAM from reseating properly. I'd recommended reseating the CPU and the memory as Nick mentioned... though SSD? Not sure why that's up there they are all screwed in place and don't just pop out, but, won't hurt either. Be mindful, do one at a time or you could fix this problem without knowing which one was the culprit.

__________________

 

About that blue screen though... even this link refers to bad RAM when all else has failed to fix that exception error.

https://www.howtogeek.com/865206/how-to-fix-a-kmode-exception-not-handled-error-in-windows/

 

It's important to point out that the microcode update from Intel is a preventative fix. The bug causes overvoltage and permanent damage to the CPU. If you are certain the CPU was already experiencing issues due to that bug (and I wouldn't be surprised if it was), it must be replaced under warranty.

If it does not work with any of the individual sticks of memory or after reseating components, then the next steps are:

  1. Visually inspect the motherboard for any damage (broken/burnt components, etc)
  2. Try it with just the CPU, CPU cooler, motherboard, memory, and power supply (no video card, extra fans, drives, etc). Connect your monitor to a motherboard video port.
  3. Try clearing CMOS (as described in the motherboard manual). Note that if you require something other than the default settings, you (or someone who can help you) must be comfortable with changing the UEFI settings later.
  4. Try a different power supply (if available). Wattage isn't too important in this bare configuration (even 250-300W is enough).
  5. Try a different CPU (if available).

Just get as far as you can. If it works at any point (gives video when you power it up), you can try booting to your Ubuntu flash drive and test how stable it is over several hours. You can install and run a stress testing utility as well.

Ok, I have already removed the cpu which it was my first time ever doing so in my entire life, I've always been nervous about damaging the cpu in the proccess, but after I watched some videos on how to unscrew my AIO cooler, which is a Corsair iCUE H150i ELITE CAPELLIX 360mm RGB Water Cooling Kit I unscrewed the screws in a criss cross pattern like my friend suggested and was able to very gentle take the cpu out, and also I already setup a RMA with intel and they've sent me the pre-paid shipping label which I was going to box up securely and send out tomorrow or in the next few days.

Ok so I was reading more comments and decided to take some pics to inspect the the motherboard, after I had removed the cpu, and i noticed a few things and now I am scared for my life and I feel sick to my stomach because I dont know if this is normal or not!!!!

1st picture - inspecting the mother board for signs of damage 

XSRUZBx.jpeg

2nd picture - after I reseated the cpu, and lowered the latch to lock it in place, the square thing that is attached to the motherboard and that surrounds the cpu, that feels like I can lift it up easily, and doesn't feel like the lid thing is all the way after I had lowered the latch, and hooked it into the side thing, is that normal!? I don't know or not!!

RNWJHft.jpeg

3rd picture - I noticed this latch that was on top, was loose and I was able to lift it off easily! it's like it came off of the aio water block somehow, but the bottom part is still attached and I don't see how or where to put the top bracket back onto the water block, is this normal? I do not know and I am scared to death!!!!!!

9CM4pPS.jpeg

 

I knew I should have just waited to have my friend come over tomorrow and take the aio cooler off, now I don't know what to do at all and I am deathly afraid I ######ed up big time, what do I do now!?! please oh my god I  am so sick and depressed already because of this issue I'm having but this just adds more on top of it! :(

Don't be alarmed. Nothing looks broken. You just need to open and close the CPU latch again.

cpusocket1.thumb.jpg.ee49b19272ef2e15fddc4818ca781da2.jpg

I have highlighted the latch. Notice that curved part at the top? It's supposed to rotate and come down on top of the edge of the lid.

  1. Open the latch and the lid of the socket. The CPU is fine where it is as long as it looks seated correctly.
  2. Close the lid fully.
  3. Now push down the latch and lock it. Watch that little curved part rotate and make sure it goes down on top of the lid to hold the lid down.
  4. Everything should be firmly in place now.

A video from the CPU cooler manufacturer may be viewed here. It's normal for those half-brackets to easily slide on and off when the CPU cooler is removed.

Whether it be a motherboard or a CPU cooler, you can usually just go to the manufacturer's website and download the manual. That will tell you all sorts of info about how to install it. Or, like in this case, you sometimes can find a video as well.

  On 09/01/2025 at 08:55, ShadeOfBlue said:

Don't be alarmed. Nothing looks broken. You just need to open and close the CPU latch again.

cpusocket1.thumb.jpg.ee49b19272ef2e15fddc4818ca781da2.jpg

I have highlighted the latch. Notice that curved part at the top? It's supposed to rotate and come down on top of the edge of the lid.

  1. Open the latch and the lid of the socket. The CPU is fine where it is as long as it looks seated correctly.
  2. Close the lid fully.
  3. Now push down the latch and lock it. Watch that little curved part rotate and make sure it goes down on top of the lid to hold the lid down.
  4. Everything should be firmly in place now.

A video from the CPU cooler manufacturer may be viewed here. It's normal for those half-brackets to easily slide on and off when the CPU cooler is removed.

Whether it be a motherboard or a CPU cooler, you can usually just go to the manufacturer's website and download the manual. That will tell you all sorts of info about how to install it. Or, like in this case, you sometimes can find a video as well.

Expand  

Ok thank you, and as for the 1st picture..does the cpu motherboard slot look fine to you? like no damaged pins or anything?

I don't see any obviously damaged pins, but I am limited by the resolution of the photo. They are actually super easy to see when they exist. Just shine a light at them and look at an angle until you see the light reflecting off the very tip of the pins just right. They form a perfect grid. You'll know it when you see it. If any pin isn't perfectly aligned with the others, it becomes really obvious as a flaw in the perfect grid pattern.

I do see what looks like a little spot of debris in the socket in the lower-left quadrant. Hard to tell. It might be a fleck of the thermal compound or something. Or just a trick of the light.

cpusocket2.jpg.00e9bcb765f50b41ced4106cb0e31016.jpg

I don't want you to worry though. Even if it's real, as long as it's not resting on the tip of a pin, it won't hurt anything. If it looks like it is large or in a bad spot (otherwise leave well enough alone), just use some canned air to gently blow it out. Never stick a tool down into the pins to retrieve something.

New motherboards come with a protective cover on the socket. They are often misplaced or thrown away, and rarely come with a new PC when purchase preassembled. If you don't have one, a precaution you can take when the CPU is removed is to close the lid and latch, then place a stiff piece of cardboard on top (one large enough to overhang the socket in all directions). It may be gently taped in place if need be. That way nothing can fall in or bump the socket pins if it is going to be sitting there exposed for a long time.

  • Like 3
  On 09/01/2025 at 09:36, ShadeOfBlue said:

New motherboards come with a protective cover on the socket. They are often misplaced or thrown away, and rarely come with a new PC when purchase preassembled. If you don't have one, a precaution you can take when the CPU is removed is to close the lid and latch, then place a stiff piece of cardboard on top (one large enough to overhang the socket in all directions). It may be gently taped in place if need be. That way nothing can fall in or bump the socket pins if it is going to be sitting there exposed for a long time.

Expand  

This is great advice, since I broke the socket pins accidentally by not applying the protective cover when the CPU was removed 😵

  On 09/01/2025 at 09:36, ShadeOfBlue said:

I don't see any obviously damaged pins, but I am limited by the resolution of the photo. They are actually super easy to see when they exist. Just shine a light at them and look at an angle until you see the light reflecting off the very tip of the pins just right. They form a perfect grid. You'll know it when you see it. If any pin isn't perfectly aligned with the others, it becomes really obvious as a flaw in the perfect grid pattern.

I do see what looks like a little spot of debris in the socket in the lower-left quadrant. Hard to tell. It might be a fleck of the thermal compound or something. Or just a trick of the light.

cpusocket2.jpg.00e9bcb765f50b41ced4106cb0e31016.jpg

I don't want you to worry though. Even if it's real, as long as it's not resting on the tip of a pin, it won't hurt anything. If it looks like it is large or in a bad spot (otherwise leave well enough alone), just use some canned air to gently blow it out. Never stick a tool down into the pins to retrieve something.

New motherboards come with a protective cover on the socket. They are often misplaced or thrown away, and rarely come with a new PC when purchase preassembled. If you don't have one, a precaution you can take when the CPU is removed is to close the lid and latch, then place a stiff piece of cardboard on top (one large enough to overhang the socket in all directions). It may be gently taped in place if need be. That way nothing can fall in or bump the socket pins if it is going to be sitting there exposed for a long time.

Expand  

I have an electric air duster can I use that? I don't have any cans of air

  On 09/01/2025 at 11:11, Sharpstick68 said:

have an electric air duster can I use that? I don't have any cans of air

Expand  

Gently

  On 09/01/2025 at 11:11, Sharpstick68 said:

I have an electric air duster can I use that? I don't have any cans of air

Expand  

If there's actually something there, and if it looks like it could cause a problem, and if simple things like tilting it in a more upside down position to let it fall out or using some paper to fan some air on it don't work, then perhaps. Just treat it carefully, don't put the nozzle too close to the socket, and don't blow more new debris into it than you blow out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Microsoft 365 Copilot Notebooks now integrated in OneNote on Windows by Paul Hill Microsoft has announced that Enterprise customers with Microsoft 365 Copilot, SharePoint, or OneDrive licenses can now use Microsoft 365 Copilot Notebooks integrated directly with OneNote on Windows. Copilot Notebooks are AI-powered and bring together different resources such as Copilot Chat, files, notes, and links into a single space to make you more productive. The Redmond giant wants to make it easier for customers to gather content, understand complex topics, and create “smarter content” with Copilot Notebooks. This integration is squarely aimed at Enterprise customers, not Personal or Family subscribers. How Copilot Notebooks enhance productivity in OneNote When you open OneNote on Windows, you should see Copilot Notebooks in the left-hand sidebar, from here you can view or edit existing notebooks or you can create one by going to Home > Create Copilot Notebook or New notebook. During the creation of your new notebook, you can give it a name and add references such as OneNote pages, .docx, .pptx, .xlsx, .pdf, or .loop files. This gives Copilot extra context to provide you with more refined answers. Once you have created a notebook and added your reference documents, you can use Copilot Notebooks to help you gather insights from your documents, draft summaries, and generate audio overviews. An important caveat to mention about these notebooks is that you can only add 20 files as references and only individual OneNote pages, as opposed to sections and notebooks, can be added. Microsoft could add support for these in the future, but you can’t add them yet. Another limitation right now is that some OneNote features aren’t functional within Copilot Notebooks, including tags, section groups, inking, templates, password protection, Immersive Reader, and offline support. Availability and what it means for enterprise users Microsoft 365 Copilot Notebooks in OneNote for Windows are available for Enterprise customers with an appropriate license (anyone with a Microsoft 365 Copilot, SharePoint, or OneDrive license) running OneNote Version 2504 (Build 18827.20128) or later. If you have any other feedback to give to Microsoft, you can give it via Help > Feedback. As an Insider preview, Microsoft will likely improve this before declaring it stable so let Microsoft know of any issues you have. Now that the feature is available as a preview, it’s the perfect time for IT admins and other decision-makers to evaluate the feature to see how it could benefit their wider organization.
    • Mixxx 2.5.2 by Razvan Serea Mixxx is powerful, free, and open-source DJ software designed for both beginners and professionals. It offers real-time beatmatching, auto DJ, effects, and MIDI controller support. With a clean interface and compatibility across Windows, macOS, and Linux, Mixxx is ideal for live performances, radio broadcasts, or practice sessions. Its active community and constant updates make it a reliable tool for any DJ. Mixxx integrates the tools DJs need to perform creative live mixes with digital music files. Whether you are a new DJ with just a laptop or an experienced turntablist, Mixxx can support your style and techniques of mixing. Mixxx key features: Realtime audio engine with low-latency performance MIDI and HID controller mapping with customizable scripting (JavaScript-based) Vinyl DVS support (absolute & relative timecode modes) OpenSL, ASIO, WASAPI, and JACK audio backend support Advanced BPM & musical key detection (KeyFinder integration) Quantized beat sync and phase locking Effect chain routing with LADSPA plugin support 4-deck mixing with independent EQ and gain control Support for wide file formats (MP3, FLAC, OGG, WAV, AIFF) Broadcasting via Icecast and Shoutcast with metadata support Library with Crate, Playlist, and Smart Playlist organization Multi-core CPU support for performance optimization Microphone and Auxiliary input routing with talkover ducking OSC and Web MIDI support Skinnable and themable Qt-based UI Cue points, hotcues, and looping with quantization Recording in lossless WAV or compressed formats Clock-synced looping and beatjump Mixxx 2.5.2 changelog: Library Fix playlist export when name contains a dot Fix loading the wrong track via drag and drop when using symlinks Fix: byte order in hotcue comments imported from rekordbox Tracks table: show ReplayGain with max. 2 decimals, full precision in tooltip Fix keyboard mappings with non-ASCII characters on Linux Computer feature: enable initial sorting during population Computer feature: avoid false-positve 'has children' for non-directory links Fix column header mapping when using external library Fixed Single track cover reload on reload metadata from file Controller Mappings Arturia KeyLab Mk1: initial mapping Denon MC7000: slicer mode TypeError Denon MC7000: crossfader curve using wrong parameter DJ TechTools MIDI Fighter Twister: support 4 decks Hercules DJControl Inpulse 500: the crossfader was not reaching 100% to the right end Icon Pro Audio iControls: initial mapping Numark Mixtrack Platinium FX: Fix 4 steps browsing issue Traktor Kontrol S3: Use GUI config for settings Traktor S2 MK3: Fixed LED issue Traktor S4 MK2: Use engine settings API for configuration Traktor S4 MK3: prevent sync lockup, add setting for tempo center snap Controller Backend Control picker: Allow to learn MIDI Aux/Mic enable controls Make [Main],headSplit CO persistent across restart Fix MIDI Controller button learning Fix learning with "No Mapping" selected Unit tests for engine.beginTimer engine-api.d.ts: brake()/spinback() documentation Target support Fix building with a CMake multi-config setup Fix building with gcc >= 14 with LTO and clang >= 19 (fpclassify) Fix: gcc -Warray-bounds= in fidlib by using a flexible member Added Linux Mint Codenames to debian_buildenv.sh Add hidden [Config],notify_max_dbg_time setting to reduce warnings in developer mode Detect arch and fail early if not supported when installing buildenv Misc Vinyl Control: Reduce sticker drift Fix infinite number of pop ups of the "No Vinyl|Mic|Aux|Passthrough input configured" dialog Reduce CPU usage with Trace log messages Fix adjust Gain after adopting it as ReplayGain only in requesting playe Skins: add loop anchor toggle to Deere, Shade, Tango Sound Hardware preferences: add manual link for Mic monitoring modes Work around an Ubuntu, Ibus or Qt issue regarding detecting the current keyboard layout. Fix BPM rounding for the 3/2 case Update cue & play indicators on paused decks when switching cue mode Download: Mixxx 2.5.2 | 113.0 MB (Open Source) Links: Mixxx Home page | Other OSes | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • KDE brings Wayland PiP to Plasma 6.5, adds finishing touches to 6.4 as release nears by David Uzondu The KDE team has released its This Week in Plasma update, showing the final polish being applied to Plasma 6.4 ahead of its June 17 release. Last week, the KDE team brought performance upgrades, and this week the team is continuing that with improvements like faster loading for System Monitor components in Plasma 6.4. Future work for Plasma 6.5 is already underway, and it includes a feature that many have probably been waiting for: proper Picture-in-Picture support on Wayland. This uses an experimental version of the Wayland PiP protocol, which means applications like Firefox that also implement it can finally display PiP windows correctly. It is a long-overdue addition that moves the Wayland session closer to feature parity with X11. The devs also merged KWin's Background Contrast effect into the Blur effect. Virtual desktops can now be re-ordered from the Pager widget, a feature previously missing. Invert and Zoom settings have been moved into the Accessibility page, which is a more sensible place for them than the Desktop Effects page was. The team also brought consistency to the Breeze application style, with animated effects for checkboxes and radio buttons now working in QtQuick-based apps. Other small cleanups include standardizing the section headers in the Disks & Devices, Networks, and Bluetooth widgets. For those who do a lot of screen recording, Spectacle now makes it much clearer how to stop a recording, both in its notifications and shortcut names. As for the immediate future, Plasma 6.4 and its first point release are getting accessibility and user interface tweaks. The team improved text contrast for labels used in secondary roles throughout Plasma, making things like brightness indicators much easier to read. The Kicker Application Menu in 6.4 can now scroll horizontally when a search returns a ton of results, so you can actually see all of them. The team also delivered some stability improvements in Plasma 6.4.0, most notably fixing a long-standing issue where adding widgets to oversized panels could freeze the entire shell. Discover also got a much-needed fix for a crash that occurred when suggesting replacements for unsupported Flatpak apps. On the usability side, dragging files into a Folder View widget no longer causes glitchy visuals, and Open and Save dialogs from Flatpak-based browsers now properly allow the preview pane to open. Printing from Flatpak GTK apps now respects correct sizing, and installing or removing apps no longer wipes out your search input in Kicker or Kickoff while you're using it. Other notable fixes include: Selection rectangles on the desktop now render properly when using custom fonts or sizes (Plasma 6.3.6) A crash in System Monitor charts used by apps and Plasma components has been resolved (Frameworks 6.15) Switching process views in System Monitor no longer causes crashes (Frameworks 6.16) Open and Save dialogs no longer close when hovering over specific files (Frameworks 6.16) A thumbnailer crash on X11 caused by certain widget styles has been fixed (KDE Gear 25.04.3) Frameworks 6.15 also speeds up System Monitor by delaying tree view arrow loading There are still 3 high-priority Plasma bugs holding out, and the list of quick-win "15-minute bugs" has grown to 23.
    • Hasleo Backup Suite Free 5.4.2.0 by Razvan Serea Hasleo Backup Suite Free is a free Windows backup and restore software, which embeds backup, restore and cloning features, it is designed for Windows operating system users and can be used on both Windows PCs and Servers. The backup and restore feature of Hasleo Backup Suite can help you back up and restore the Windows operating systems, disks, partitions and files (folders) to protect the security of your Windows operating system and personal data. The cloning feature of Hasleo Backup Suite can help you migrate Windows to another disk, or easily upgrade a disk to an SSD or a larger capacity disk. System Backup & Restore / Disk/Partition Backup & Restore Backup Windows operating system and boot-related partitions, including user settings, drivers and applications installed in these partitions, which ensures that you can quickly restore your Windows operating system once it crashes. Viruses, power failure, or other unknown reasons may cause data loss, so it is a good habit to regularly back up the drive that stores important files, you can at least recover lost files from the backup image files in the event of a disaster. System Clone / Disk Clone / Partition Clone Migrate the Windows operating system from one disk to another SSD or larger disk without reinstalling Windows, applications and drivers. Clone entire disk to another disk and ensure that the contents of the source disk and the destination disk are exactly the same. Clone a partition completely to the specified location on the current disk or another disk and ensure that the data will not be changed. File Backup & Restore Back up specified files(folders) instead of the entire drive to another location to protect your data, so you can quickly restore files(folders) from the backup image files when needed. Incremental/Differential/Full Backup Different backup modes are supported, you can flexibly choose data protection schemes, which can improve backup performance and save storage space while ensuring data security. Delta Restore Delta restore uses advanced delta detection technology to check the changed blocks on the destination drive and restore only the changed blocks, so it has a faster restore speed than the traditional full restore. Universal Restore This feature can help us restore the Windows operating system to computers with different hardware and ensure that Windows can work normally without any hardware compatibility issues. Hasleo Backup Suite 5.4.2.0 changelog: Added backup image delete feature Added storage path management feature Improved file backup feature Show application notifications in Windows Notification Center Various other bug fixes and feature improvements Download: Hasleo Backup Suite 5.4.2.0 | 34.4 MB (Freeware) Links: Hasleo Backup Suite Website | Hasleo Backup Suite Guide | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
  • Recent Achievements

    • One Month Later
      5i3zi1 earned a badge
      One Month Later
    • Week One Done
      5i3zi1 earned a badge
      Week One Done
    • Week One Done
      julien02 earned a badge
      Week One Done
    • One Year In
      Drewidian1 earned a badge
      One Year In
    • Explorer
      Case_f went up a rank
      Explorer
  • Popular Contributors

    1. 1
      +primortal
      545
    2. 2
      ATLien_0
      227
    3. 3
      +FloatingFatMan
      159
    4. 4
      Michael Scrip
      113
    5. 5
      +Edouard
      98
  • Tell a friend

    Love Neowin? Tell a friend!