Computer crashed, can't get into Windows no more..


Recommended Posts

So I was playing a game last night and my computer froze, I had to reset it by holding the power button..after I did that I was greeted with a blue screen (see below) and I said ok. Next thing, I see something that says MSI starting automatic repair (relating to windows I guess) let it do that for about 5 mins and it never did boot into windows so I reset the system again and powered it back on, and also before that I went into the bios to try and see if I can get into recovery/safe mode from there but couldn't find anything. So now, when I try powering my system on, the fans come on, start spinning and rgb goes on and everything, but there is a red light on the motherboard and it won't go away and also I get no video signal from my monitor either. So far I've tried flashing my bios (see specs below) and clearing the cmos, and still nothing.

My system specs are...

Intel i7-13700K CPU

MSI Z790 MPG Edge WiFi DDR4 Motherboard

Corsair Vengeance RGB RT 32GB (2 x 16GB) DDR4-3600 PC4-28800 RAM

EVGA RTX 3070 FTW3 Graphics Card

Corsair RMx Series RM1000x 1000 Watt PSU

Corsair iCUE H150i ELITE CAPELLIX 360mm RGB Water Cooling Kit

Everything was working fine before this happened. I did update my motherboard bios a few weeks back because I finally started having problems with games crashing, due to the 13/14th gen intel cpu's problems thats been happening, something to do with the microcode or whatever it is. I had this system built November 2022 by microcenter, and it's just so frustrating to learn about these problems intel cpu chips are having, it makes me not want to trust intel any more because I don't know how recently it started happening but as far as I know it affects 13 and 14th gen chips. Anyway, sorry for the rant..I just don't know what else to try before bringing it to microcenter so they dcan diagnose the issue.

 

 

20250106_211749.jpg

On 07/01/2025 at 17:08, Sharpstick68 said:

it's just so frustrating to learn about these problems intel cpu chips are having, it makes me not want to trust intel any more

it is quite possible that the problem here is un-related to the Intel CPU you have.

On 07/01/2025 at 17:08, Sharpstick68 said:

there is a red light on the motherboard

try re-seating the components especially the CPU if you haven't already

On 07/01/2025 at 05:38, Sharpstick68 said:

so I reset the system again

Do you mean you performed a system reset as in a Windows re-install choosing to keep personal files and programs or you just did a hard shutdown by holding the power button until it turned off?

 

I am assuming you just held the power button down as mentioned earlier in your post but want to make sure.

 

Lets see if you can boot from a linux USB. If so, you can use it to backup your important files.

On another PC: https://ubuntu.com/tutorials/create-a-usb-stick-on-windows#1-overview

Edited by xrobwx71
  • Like 2

Trying a live USB is a good start.

Also, when you power on the computer I think you can get into the advanced options - which is where safe mode is located - by powering off your computer when you see the Windows logo. You need to do that three times, then the automatic repair will appear on the next boot, followed by the option to go to advanced options.

A quick search shows that the most common reason for the error message is a driver issue, so booting into safe mode should at least get you access to the system.

On 07/01/2025 at 07:40, xrobwx71 said:

Do you mean you performed a system reset as in a Windows re-install choosing to keep personal files and programs or you just did a hard shutdown by holding the power button until it turned off?

 

I am assuming you just held the power button down as mentioned earlier in your post but want to make sure.

 

Lets see if you can boot from a linux USB. If so, you can use it to backup your important files.

On another PC: https://ubuntu.com/tutorials/create-a-usb-stick-on-windows#1-overview

Sorry I should have worded that better. When I said I performed a system reset, I meant as in I held the power button down on the case so the system shuts off, that is what I meant.

Based on the manual for your motherboard, it looks like the red LED indicates an issue with the CPU.  As some of the others have said, try removing the CPU and cooler and reseating them.  Ideally you'd want to put fresh thermal paste on, but you can do that later if you get it working.

You could also try removing a stick of RAM and seeing if it'll boot with 1 stick.  Try with each stick individually to see if maybe one of them is bad.
Also try removing and reconnecting all the power supply cables.  Maybe one wasn't seated correctly and isn't supplying sufficient power.

You could try a live USB linux distro just to see if the PC will at least function.  That would then tell you if it's a hardware issue or a Windows install issue.
And if all of these things fail, then maybe your CPU did indeed fail.

image.png.b5fb533522c5f43165f6106c9307ebe7.png

On 07/01/2025 at 13:47, Astra.Xtreme said:

Based on the manual for your motherboard, it looks like the red LED indicates an issue with the CPU.  As some of the others have said, try removing the CPU and cooler and reseating them.  Ideally you'd want to put fresh thermal paste on, but you can do that later if you get it working.

You could also try removing a stick of RAM and seeing if it'll boot with 1 stick.  Try with each stick individually to see if maybe one of them is bad.
Also try removing and reconnecting all the power supply cables.  Maybe one wasn't seated correctly and isn't supplying sufficient power.

You could try a live USB linux distro just to see if the PC will at least function.  That would then tell you if it's a hardware issue or a Windows install issue.
And if all of these things fail, then maybe your CPU did indeed fail.

image.png.b5fb533522c5f43165f6106c9307ebe7.png

I will try what you are suggesting, but just a few questions for clarification

Should I leave my AIO cooler off and booting my system up? or should I reseat the cpu and put the cooler back on before testing again..

I also want to try removing 1 stick of ram to see if the memory could be the problem also

On 07/01/2025 at 21:46, Sharpstick68 said:

I will try what you are suggesting, but just a few questions for clarification

Should I leave my AIO cooler off and booting my system up? or should I reseat the cpu and put the cooler back on before testing again..

I also want to try removing 1 stick of ram to see if the memory could be the problem also

No. You should start from the basics and work up.

Does a live USB key work?

Can you access safe mode?

Have you switched off the cooler?

Have you reseated the standard devices that possibly cause the error code?

On 07/01/2025 at 15:46, Sharpstick68 said:

I will try what you are suggesting, but just a few questions for clarification

Should I leave my AIO cooler off and booting my system up? or should I reseat the cpu and put the cooler back on before testing again..

I also want to try removing 1 stick of ram to see if the memory could be the problem also

You always want to have the cooler completely installed.  Without the cooler, the CPU is going to overheat extremely fast.  I guess you could run it without the cooler for a few seconds just to see if the PC will get further in the boot process, but definitely don't run it for long that way.

On 07/01/2025 at 16:55, Nick H. said:

No. You should start from the basics and work up.

Does a live USB key work?

Can you access safe mode?

Have you switched off the cooler?

Have you reseated the standard devices that possibly cause the error code?

No a live USB key doesn't work

No I can not access safe mode

What do you mean when you say "Have I switched off the cooler?"

No can you explain what that may be? I have already checked to make sure the power cables are all firmly and tightly plugged in, all cables appear to be fully and securely in place

On 07/01/2025 at 22:03, Sharpstick68 said:

No a live USB key doesn't work

No I can not access safe mode

What do you mean when you say "Have I switched off the cooler?"

No can you explain what that may be? I have already checked to make sure the power cables are all firmly and tightly plugged in, all cables appear to be fully and securely in place

A live USB doesn't work? Ok, that's an issue. That probably means that the problem is with the hardware rather than with Windows.

If you can't access safe mode via the instructions I provided...well, given your above response I'm ok with that, since the problem isn't with Windows.

"Switched off" or in any way disconnecting the cooling system from the rest of the system. We're working towards the idea that the issue is hardware based, so disconnecting the cooler would be a good start. It's not necessary, it's just nice to have.

And to the last point, since you'll be opening the box and disconnecting the cooling system, you may as well take out the RAM and SSD (or HDD) and plug them back in again (i.e. "reseating"). There's a reason that there is the stupid idea of "have you tried turning it off and on again?" Same applies to hardware. Take it out, put it back in. And if you can, try a different location.

On 07/01/2025 at 11:24, Sharpstick68 said:

When I said I performed a system reset, I meant as in I held the power button down on the case so the system shuts off, that is what I meant.

Heh.. yeah, affectionately referred to as a "hard" reset.

 

That red CPU light may and may not indicate the CPU... as I have an MSI board. Last time I cleaned it, I left the CPU in.. but removed all the rest of the components on the board.

When I had it all back together, she wouldn't boot at all.. and all I had was that red CPU light.

 

Found out there was a tiny wire from the CPU cooler that prevented a stick of RAM from reseating properly. I'd recommended reseating the CPU and the memory as Nick mentioned... though SSD? Not sure why that's up there they are all screwed in place and don't just pop out, but, won't hurt either. Be mindful, do one at a time or you could fix this problem without knowing which one was the culprit.

__________________

 

About that blue screen though... even this link refers to bad RAM when all else has failed to fix that exception error.

https://www.howtogeek.com/865206/how-to-fix-a-kmode-exception-not-handled-error-in-windows/

 

It's important to point out that the microcode update from Intel is a preventative fix. The bug causes overvoltage and permanent damage to the CPU. If you are certain the CPU was already experiencing issues due to that bug (and I wouldn't be surprised if it was), it must be replaced under warranty.

If it does not work with any of the individual sticks of memory or after reseating components, then the next steps are:

  1. Visually inspect the motherboard for any damage (broken/burnt components, etc)
  2. Try it with just the CPU, CPU cooler, motherboard, memory, and power supply (no video card, extra fans, drives, etc). Connect your monitor to a motherboard video port.
  3. Try clearing CMOS (as described in the motherboard manual). Note that if you require something other than the default settings, you (or someone who can help you) must be comfortable with changing the UEFI settings later.
  4. Try a different power supply (if available). Wattage isn't too important in this bare configuration (even 250-300W is enough).
  5. Try a different CPU (if available).

Just get as far as you can. If it works at any point (gives video when you power it up), you can try booting to your Ubuntu flash drive and test how stable it is over several hours. You can install and run a stress testing utility as well.

Ok, I have already removed the cpu which it was my first time ever doing so in my entire life, I've always been nervous about damaging the cpu in the proccess, but after I watched some videos on how to unscrew my AIO cooler, which is a Corsair iCUE H150i ELITE CAPELLIX 360mm RGB Water Cooling Kit I unscrewed the screws in a criss cross pattern like my friend suggested and was able to very gentle take the cpu out, and also I already setup a RMA with intel and they've sent me the pre-paid shipping label which I was going to box up securely and send out tomorrow or in the next few days.

Ok so I was reading more comments and decided to take some pics to inspect the the motherboard, after I had removed the cpu, and i noticed a few things and now I am scared for my life and I feel sick to my stomach because I dont know if this is normal or not!!!!

1st picture - inspecting the mother board for signs of damage 

XSRUZBx.jpeg

2nd picture - after I reseated the cpu, and lowered the latch to lock it in place, the square thing that is attached to the motherboard and that surrounds the cpu, that feels like I can lift it up easily, and doesn't feel like the lid thing is all the way after I had lowered the latch, and hooked it into the side thing, is that normal!? I don't know or not!!

RNWJHft.jpeg

3rd picture - I noticed this latch that was on top, was loose and I was able to lift it off easily! it's like it came off of the aio water block somehow, but the bottom part is still attached and I don't see how or where to put the top bracket back onto the water block, is this normal? I do not know and I am scared to death!!!!!!

9CM4pPS.jpeg

 

I knew I should have just waited to have my friend come over tomorrow and take the aio cooler off, now I don't know what to do at all and I am deathly afraid I ######ed up big time, what do I do now!?! please oh my god I  am so sick and depressed already because of this issue I'm having but this just adds more on top of it! :(

Don't be alarmed. Nothing looks broken. You just need to open and close the CPU latch again.

cpusocket1.thumb.jpg.ee49b19272ef2e15fddc4818ca781da2.jpg

I have highlighted the latch. Notice that curved part at the top? It's supposed to rotate and come down on top of the edge of the lid.

  1. Open the latch and the lid of the socket. The CPU is fine where it is as long as it looks seated correctly.
  2. Close the lid fully.
  3. Now push down the latch and lock it. Watch that little curved part rotate and make sure it goes down on top of the lid to hold the lid down.
  4. Everything should be firmly in place now.

A video from the CPU cooler manufacturer may be viewed here. It's normal for those half-brackets to easily slide on and off when the CPU cooler is removed.

Whether it be a motherboard or a CPU cooler, you can usually just go to the manufacturer's website and download the manual. That will tell you all sorts of info about how to install it. Or, like in this case, you sometimes can find a video as well.

On 09/01/2025 at 03:55, ShadeOfBlue said:

Don't be alarmed. Nothing looks broken. You just need to open and close the CPU latch again.

cpusocket1.thumb.jpg.ee49b19272ef2e15fddc4818ca781da2.jpg

I have highlighted the latch. Notice that curved part at the top? It's supposed to rotate and come down on top of the edge of the lid.

  1. Open the latch and the lid of the socket. The CPU is fine where it is as long as it looks seated correctly.
  2. Close the lid fully.
  3. Now push down the latch and lock it. Watch that little curved part rotate and make sure it goes down on top of the lid to hold the lid down.
  4. Everything should be firmly in place now.

A video from the CPU cooler manufacturer may be viewed here. It's normal for those half-brackets to easily slide on and off when the CPU cooler is removed.

Whether it be a motherboard or a CPU cooler, you can usually just go to the manufacturer's website and download the manual. That will tell you all sorts of info about how to install it. Or, like in this case, you sometimes can find a video as well.

Ok thank you, and as for the 1st picture..does the cpu motherboard slot look fine to you? like no damaged pins or anything?

I don't see any obviously damaged pins, but I am limited by the resolution of the photo. They are actually super easy to see when they exist. Just shine a light at them and look at an angle until you see the light reflecting off the very tip of the pins just right. They form a perfect grid. You'll know it when you see it. If any pin isn't perfectly aligned with the others, it becomes really obvious as a flaw in the perfect grid pattern.

I do see what looks like a little spot of debris in the socket in the lower-left quadrant. Hard to tell. It might be a fleck of the thermal compound or something. Or just a trick of the light.

cpusocket2.jpg.00e9bcb765f50b41ced4106cb0e31016.jpg

I don't want you to worry though. Even if it's real, as long as it's not resting on the tip of a pin, it won't hurt anything. If it looks like it is large or in a bad spot (otherwise leave well enough alone), just use some canned air to gently blow it out. Never stick a tool down into the pins to retrieve something.

New motherboards come with a protective cover on the socket. They are often misplaced or thrown away, and rarely come with a new PC when purchase preassembled. If you don't have one, a precaution you can take when the CPU is removed is to close the lid and latch, then place a stiff piece of cardboard on top (one large enough to overhang the socket in all directions). It may be gently taped in place if need be. That way nothing can fall in or bump the socket pins if it is going to be sitting there exposed for a long time.

  • Like 3
On 09/01/2025 at 10:36, ShadeOfBlue said:

New motherboards come with a protective cover on the socket. They are often misplaced or thrown away, and rarely come with a new PC when purchase preassembled. If you don't have one, a precaution you can take when the CPU is removed is to close the lid and latch, then place a stiff piece of cardboard on top (one large enough to overhang the socket in all directions). It may be gently taped in place if need be. That way nothing can fall in or bump the socket pins if it is going to be sitting there exposed for a long time.

This is great advice, since I broke the socket pins accidentally by not applying the protective cover when the CPU was removed 😵

On 09/01/2025 at 04:36, ShadeOfBlue said:

I don't see any obviously damaged pins, but I am limited by the resolution of the photo. They are actually super easy to see when they exist. Just shine a light at them and look at an angle until you see the light reflecting off the very tip of the pins just right. They form a perfect grid. You'll know it when you see it. If any pin isn't perfectly aligned with the others, it becomes really obvious as a flaw in the perfect grid pattern.

I do see what looks like a little spot of debris in the socket in the lower-left quadrant. Hard to tell. It might be a fleck of the thermal compound or something. Or just a trick of the light.

cpusocket2.jpg.00e9bcb765f50b41ced4106cb0e31016.jpg

I don't want you to worry though. Even if it's real, as long as it's not resting on the tip of a pin, it won't hurt anything. If it looks like it is large or in a bad spot (otherwise leave well enough alone), just use some canned air to gently blow it out. Never stick a tool down into the pins to retrieve something.

New motherboards come with a protective cover on the socket. They are often misplaced or thrown away, and rarely come with a new PC when purchase preassembled. If you don't have one, a precaution you can take when the CPU is removed is to close the lid and latch, then place a stiff piece of cardboard on top (one large enough to overhang the socket in all directions). It may be gently taped in place if need be. That way nothing can fall in or bump the socket pins if it is going to be sitting there exposed for a long time.

I have an electric air duster can I use that? I don't have any cans of air

On 09/01/2025 at 05:11, Sharpstick68 said:

have an electric air duster can I use that? I don't have any cans of air

Gently

On 09/01/2025 at 05:11, Sharpstick68 said:

I have an electric air duster can I use that? I don't have any cans of air

If there's actually something there, and if it looks like it could cause a problem, and if simple things like tilting it in a more upside down position to let it fall out or using some paper to fan some air on it don't work, then perhaps. Just treat it carefully, don't put the nozzle too close to the socket, and don't blow more new debris into it than you blow out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • On the topic of being locked out of a service. Recently two different friends of mine got locked out of their Google accounts. Both were hack attempts and one of them is waiting 30 days before he can get back in. He had backup codes and MFA but not a passkey. It was a browser token hack. Anyhow he has to wait 30 days for the dispute or whatever to end. The other person only had a password and is screwed losing all of the email, docs and years of photos. Google won’t help her at all. Her fault because she had no backup/recovery setup. Enable passkeys if possible. Also do NOT use browser based password managers. If using a cloud service make sure it is one you can fully sync to one of your devices so you can back it up. Like a PC or Mac with some backup drive plugged into it. Google is the worst to use IMHO. You can’t sync your photos at all. You have to use the “Take Out” service which is manual and takes days. That service strips the meta data from your photos. Also Google Docs synced to a device are useless without a Google accounts. MS Office/Libre Office is not going to open a link to a Google doc to a dead account.
    • Why you need to take back control of your synced passwords and how to go about doing that by Paul Hill Credit: Pixabay Last month, when Google decided to introduce daily and weekly caps for Gemini, it reignited an anxiety of mine, that you can’t really depend on service providers to maintain features forever, and it got me looking into free software (as in freedom) in other areas too. One app I quickly came across was KeePassXC on desktop and KeePassDX on Android as an alternative to password manager lock-in within the Chrome or Firefox ecosystems. I personally like to switch around with browsers, and using either password manager is inconvenient, so something like KeePassXC was interesting to me. The main issue with it now is syncing; I was not sure how to do that. After a bit of research, I came across Syncthing, a tool I was vaguely familiar with but had never used because it seemed complicated. However, I was completely wrong, and honestly, I think everyone should use it if they use multiple devices. It essentially lets you share folders peer to peer across all of your devices, no cloud services that you don’t control necessary! And it was fairly simple to set up, if not a bit clunky. Since setting it up, I’ve also started using Syncthing to back up other apps too, so don’t think it’s limited to just saving password databases. You can use it for pretty much anything you use Dropbox or Google Drive for. Before continuing to talk about those apps a bit more, let’s walk back a bit and talk about browser sync. Ever since the late 2000s and early 2010s, really, since we have been using smartphones, browser sync has been a necessity of life. I don’t know about you, but I have hundreds of passwords saved. For the most part, they’re all unique, so I don’t remember them and rely on software to manage them for me. Until recently, I’ve relied on password managers in Chrome and Firefox, but what I always found annoying was that it can be hard to transfer them between browsers. Sure, on Windows it is simple enough, but on Linux, exporting bookmarks has been temperamental. It works OK nowadays, but not too long ago, Chrome required you to enable exporting passwords in chrome://flags. The situation is even worse on mobile; there is no exporting or importing of passwords of any kind. You literally have to do it on a desktop, which is incredibly annoying in our mobile-first world. Sync also lets us take out bookmarks, history, tabs, and autofill data easily. To enable sync, it’s just a matter of signing into the browser once, and it handles the rest. It’s nice and easy. Obviously, all this has some issues, including those I’ve outlined above about it being hard to transfer data between browsers, but also things such as account suspension, lost account passwords, and other lock-in mechanisms, such as passkeys, being tied to a specific browser. On a sidenote, I have just removed all of my passkeys because they can make it harder to move browsers. I think the biggest threat to your synced passwords, especially if doing this with Google, is having your account suspended. I don’t ever expect mine to be suspended, but you do hear horror stories on Reddit where people lose access to their Google accounts. Imagine if you have hundreds of passwords, then suddenly lose access to them because Google froze your account, what would you do? So yes, it can be nice to use these syncing services for their convenience, but they also have risks. You may have seen me going on about free software quite a bit in my editorials. It’s essentially a concept championed by the Free Software Foundation. It’s software under particular licenses that grant you four freedoms: run the program for any purpose (0), study and change the source code (1), redistribute copies to others (2), and the freedom to distribute modified copies to others (3). For example, if there is an app I use and one day it gets abandoned by the developer, I can keep running it or even clone the software and continue developing it. Look at the myriad of cool services Google has run over the years before killing them. You can’t take the source code for those because they are proprietary, for the most part. Both KeePassXC and Syncthing are free software, so I get the freedoms listed above. In my use case where I’m syncing a database full of my passwords, I also get proper ownership over my data, there is no losing access to the database due to a frozen account, I can access the code of the tools I’m using, and I can get support from real people online if I run into issues, rather than having to consult a vague help page from an opaque company. With the KeePassXC password manager, you create a .kdbx file, which is what will be synced between devices. KeePassXC has cross-platform apps and also has browser extensions so that the browser can fetch passwords from the database once it is unlocked. Meanwhile, Syncthing is a peer-to-peer file sync tool where you can select folders to sync between your devices. Just pop files in the folders you choose, and then they will be available across your other devices whenever they come online. Syncthing is resilient as it works over both LAN and the internet and only ever sends content between your devices, never to a third-party server somewhere else. By combining these two pieces of software, you can essentially replicate the browser sync functionality. I have had a weird, conflicting issue where a new file is appearing, but it doesn’t seem to be impacting my main password database, which is updating between devices just fine. If you want to get a setup similar to what I have, you will need to go here to download KeePassXC for your computer. Once you have that, you will need to download your passwords from your web browser to a CSV file. In Chrome, you can type chrome://password-manager/settings into the URL bar, and you should see an option to download your passwords under Export Passwords. This will give you the CSV file you need for importing into KeePassXC. If you use a different browser, just use a search engine and type “browser-name export passwords” and muddle along. In KeePassXC, you’ll want to press Import File from the home screen, select the CSV file, and create a new database from it. On one of the screens of the wizard, there will be a Title field with a drop-down selected to none. Change this to Title and continue. You’ll select a name for the database, the encryption level (the defaults are fine), and then you will pick a password. I would choose four unrelated words that are easy for you to remember, as you’ll be typing them fairly often to access your passwords. When you have all your passwords in your new database, you will want to set up the browser extension so that your browser can fetch passwords from KeePassXC. Rather than explain how to do that here, refer to KeePassXC’s guide on how to set it up properly. Once you’ve got that set up, you want to install KeePassDX on Android. You can grab it on the F-Droid store and the Google Play Store. For iPhone users, there are other .kdbx-supporting apps, but I haven’t tried any of them, so have a look around and use what suits you. Once you have that done, you will want to install Syncthing on your computer and find a third-party app for your mobile device. On Android, I use an app called BasicSync; there are also options for iOS, but again, I’ve not tried these. Once you’ve got SyncThing, you’ll want to set it up and connect all of your devices together and share a folder between your gadgets. PCWorld has a good tutorial on setting up a synchronized file between your devices using SyncThing. Once you’ve set it up, congrats, you’ll never have to touch that stuff again except for adding or removing devices. I’ll be honest, I didn’t particularly like setting up Syncthing. It didn’t take me a massive amount of time, but I think I had to check online because I found it a bit confusing. That said, I’ve had it running for several weeks now and never need to touch the Syncthing settings, so that’s very nice. I also mentioned a conflicting file. I’m not sure why this is appearing, but the main .kdbx file seems to be updating and syncing just fine. What’s nice is that both KeePassXC and Syncthing are free software, so they won’t just vanish one day; you can take the code and fork the project or use a range of alternative implementations that others have made. It’s also nice that it works over LAN, so even if your ISP is having problems, your passwords will still sync. One area where you will want to be a bit more careful with this setup is if you only have one device. I am OK because I have a computer and two phones, all synced up. If you just have one device, you will probably want to store a backup of your .kdbx file somewhere else. Obviously, you’ll also want to remember your password really well, too. If you get locked out, it's game over. Overall, if you want to take back control of your computing from big tech, taking control of your passwords is an important part of this. You don’t need to immediately clear out your browser’s password manager; try running KeePassXC and the password manager concurrently for a while to see if you run into any problems. If you do try this out, let us know some other creative ways to use Syncthing. I haven’t really come up with a solution about what to do with my bookmarks, for example.
    • If the price was a dollar, someone would complain "Why isn't it free?" If it was free, someone would complain they weren't being paid to play it.
    • That lens of history will burn if you hold it at the right angle... Warn users too late: Shame, Microsoft! That extremely minor update to an obscure Control Panel widget required 2 years of warning. Warn users too early: Shame, Microsoft! We've got better things to do. Pipeline and process be damned, we'll just always be disappointed, eh?
    • Microsoft Paint used to be my favorite Windows app as a kid, and it's still pretty good by Usama Jawad I have been using Windows since the early 2000s, when I was around 10 years old or so. I vaguely remember playing around with Windows 98 and Windows 2000, but that may have been on school PCs which had old operating systems installed. My main OS on the home PC, and the one I recall spending most time with, was Windows XP. At that time, I used the home PC to create Word and PowerPoint documents for school, but a lot of the time, I simply used it to play games. My dad would bring game discs which we would try and install on the PC, sometimes unsuccessfully, and sometimes, we would rely on flash games in the browser, like Bubble Trouble on Miniclip. However, the problem with the latter approach was the internet speed. On a good day, our dial-up internet would offer us speeds of 56 kbps, but on most days, it was closer to 33 kbps. This did not facilitate online gaming as I would often have to wait minutes for a game to load or "draw" on the screen, and trying to download pirated games wasn't simple either. I remember getting tired of waiting for online games to load and just downloading simulator games from the Big Fish Games website instead, only to be disappointed after finding out that I was just being given access to trial versions of the title, and I needed to fork out money to pay for the full version. All of this is to say that it wasn't very easy to find entertainment options on the home PC when I was a kid, due to a number of reasons, mostly outside of my control. This situation pushed me towards a rather unconventional ally: Microsoft Paint. Whenever the internet wasn't working as good as I expected, I would simply spin up Paint and draw complete rubbish on the canvas. Of course, that wasn't always the intention, but it usually happened when I messed up drawing a straight line or something, and then I would give up on that particular piece and simply draw a random collection of objects. Microsoft Paint was extremely accessible and easy to use. Even if you weren't an artist, you could quickly understand the tools at your disposal and how to leverage them on a canvas. The absolute breadth on offer ensured that each painting was truly unique, as you could utilize various combinations of tools like the pencil, paint, spray paint, and more to truly personalize your creation. Since I wasn't particularly good at drawing both on digital screen or a physical screen, I remember that my main style of art would be to insert a bunch of randomly intersecting lines and then fill them with random colors through the paint can. I have trying to replicate that art style in the latest version of Paint below, and as you can see, it's truly Pablo Picasso-esque. The human imagination truly knows no bounds Microsoft Paint kept me occupied for hours and was my best friend when video games on the home PC were inaccessible for one reason or the other. There was no academic or professional reason for which I would need to use Paint, but I still loved using it in my personal time, even if what I created wasn't worth being shown to anyone. It was simply fun. Fast-forward to today, and the situation is mostly the same. Now that I am almost 29 years old, and I still have no reason to use Microsoft Paint in a professional capacity. In fact, I don't even use it in a personal capacity, except to dabble with it from time to time, just to see if core functionalities are still intact. And I'm happy to say that I think Microsoft Paint still offers the same accessibility and inviting experience that it did to me a couple of decades ago, even though its UX has been refreshed and it's been integrated with Copilot features. Interestingly, things could have been a lot different, had Microsoft had its way. Microsoft Paint was marked for deprecation with the Windows 10 Fall Creators Update in 2017, and even began displaying a product retirement alert, urging customers to shift to Paint 3D instead. Fortunately, after consumer backlash, Microsoft reversed course on this decision, and Paint continues to be a native app inside Windows installations that can also be updated quite frequently through the Microsoft Store. Instead, Paint 3D ended up on the chopping block, which is for the better, I think. I have intermittently played around with Microsoft's refreshed Paint experience in the past few years, and I do think it has received worthwhile upgrades. the UI and the UX has been modernized while retaining core functionality, and the app is still fairly easy to use. It doesn't meet any of my use-cases, but I've never really had any use-cases ever, as described previously. Of course, the elephant in the room is the Copilot integration. Personally, I believe that this is one place where Copilot does make sense, environmental concerns aside. I know that a lot of creatives use AI to generate images, and while some may be using professional alternatives, Paint still offers a decent casual experience, with the power of Copilot. Of course, you do need to have a valid Microsoft 365 Copilot license and available credits to use it, but even if you don't, you still get the big Copilot button in the toolbar, unfortunately. All in all, I am glad that Microsoft Paint continues to be a native feature in Windows 11, and a piece of software that has evolved to meet modern needs without cutting off its own roots. It's just an iconic piece of Windows history that was an essential part of my childhood, and while I don't use it anymore, I'm just glad it is still there.
  • Recent Achievements

    • Week One Done
      Supreme Spray LV earned a badge
      Week One Done
    • One Month Later
      Genuinetonerink- Dubai earned a badge
      One Month Later
    • Week One Done
      Genuinetonerink- Dubai earned a badge
      Week One Done
    • One Year In
      hhgygy earned a badge
      One Year In
    • Week One Done
      AMV earned a badge
      Week One Done
  • Popular Contributors

    1. 1
      +primortal
      513
    2. 2
      +Edouard
      163
    3. 3
      PsYcHoKiLLa
      88
    4. 4
      Steven P.
      74
    5. 5
      Michael Scrip
      73
  • Tell a friend

    Love Neowin? Tell a friend!