Computer crashed, can't get into Windows no more..


Recommended Posts

ok i will try that, and one last thing..should I have my friend try to reseat the cpu and cooler and see if I can get my system to boot? I have the rma already created and have the pre-paid shipping label from intel, I just want to know if its worth trying to reseat it before sending the cpu back to intel

If your friend is coming over to troubleshoot, I would also suggest trying to boot with one memory stick, try one, boot, see if it works and then again with the other memory stick like what was suggested in an earlier post.

Then you can at least rule out memory being the issue.

  On 09/01/2025 at 14:10, Steven P. said:

If your friend is coming over to troubleshoot, I would also suggest trying to boot with one memory stick, try one, boot, see if it works and then again with the other memory stick like what was suggested in an earlier post.

Then you can at least rule out memory being the issue.

Expand  

should I try with one memory stick in the same ram slot, or use a slot that that hasn't been used before? and should i put my video card in as well when testing with the one stick of ram?

so my friend hasnt come over yet to try and do the reseating of the cpu and cooler like I said yet, but I did show a picture of my motherboard with the thermal paste debris on the motherboard socket to someone at a local repair shop, to see if he can be cleaned it off easily. And he sent me back the picture I showed him and circled 2 areas and said those 2 areas are damage to the socket (not covered by thermal grease) and recommended I change the board and that my cpu should be ok. I just want to get a second opinion, I will also ask my friend for his opinion on what he thinks, but just trying to figure out if I should go ahead and get a new motherboard now or not..

 

!thermal_debris_cpu_socket.thumb.jpg.8700419d0ec2765f1586a45b08479505.jpg

and this is what the person at the repair shop replied back with to my e-mail "Check the 2 areas I circled. They are damage to the socket (not covered by thermal grease). You should consider changing the board, I'm sure the CPU is ok and the mobo is the culprit."

I`d personally hold off on getting a new board just yet, you haven`t a clue yet if it`s the motherboard, CPU or even the GPU!

Try and get the area as clean as possible, tip it upside down if possible so bits can just fall off, just watch the pins.

When your friend comes over and helps put it back together try starting the system with the graphics card removed and the HDMI cable plugged into the socket on the motherboard. That at least takes the GPU out of the equation, move on from there.

If you try with just one stick of memory, that would go in slot DIMMA2 (second slot from the CPU), the second stick should go in DIMMB2 (furthest slot away from the CPU)

Good luck buddy, hopefully you`ll get there in the end...

 

slot.png

The MB's diagnostic lights usually don't lie. If your MB manual says red is a CPU problem then it's more than very likely a cpu problem. If the MB's diagnostic reports a problem then the MB is likely fine a dead MB usually do nothing outside of proviging current to fans and leds. So it's likely either the socket or cpu itself.

Edited by LaP

Unfortunately, I do see at least 2 bent pins in the new photo. The one closer to the center is important. The other appears to be for hardware debugging and is not used in normal operation, though it is important that it doesn't touch any neighboring pins.

This must be damage that just happened. I don't think it explains the earlier booting problem because then it should have acted the same way since it was first assembled. The CPU is still the likely culprit for that.

Do you need a new motherboard? That's highly likely. You should make peace with buying one before going any further. But...

If I were working on this board, I would remove the debris with some micro tweezers, and I'd bend the pins back with some dental picks or other appropriate tools. All the while I'd be inspecting everything with a loupe magnifier. It's an art.

Unless you've done stuff like that before, failure is pretty likely. That's why I don't normally recommend inexperienced users to stick tools anywhere near those pins. Since there's nothing to lose at this point, though, why not learn? I mentioned some tools you may not have, but I'm sure you could come up with something. But I'll leave it to you to decide how adventurous you want to be.

Either way, don't install a CPU and apply power until you have a good socket.

  On 10/01/2025 at 00:18, ShadeOfBlue said:

Unfortunately, I do see at least 2 bent pins in the new photo. The one closer to the center is important. The other appears to be for hardware debugging and is not used in normal operation, though it is important that it doesn't touch any neighboring pins.

This must be damage that just happened. I don't think it explains the earlier booting problem because then it should have acted the same way since it was first assembled. The CPU is still the likely culprit for that.

Do you need a new motherboard? That's highly likely. You should make peace with buying one before going any further. But...

If I were working on this board, I would remove the debris with some micro tweezers, and I'd bend the pins back with some dental picks or other appropriate tools. All the while I'd be inspecting everything with a loupe magnifier. It's an art.

Unless you've done stuff like that before, failure is pretty likely. That's why I don't normally recommend inexperienced users to stick tools anywhere near those pins. Since there's nothing to lose at this point, though, why not learn? I mentioned some tools you may not have, but I'm sure you could come up with something. But I'll leave it to you to decide how adventurous you want to be.

Either way, don't install a CPU and apply power until you have a good socket.

Expand  

I see. And I suspect the damage to those motherboard happened recently when I took off the aio cooler block, I knew I shouldn't have done it myself!. I will eventually buy a new motherboard and replace the one with the bent pins, but...should I still continue with the RMA for my processor with intel? or should I hold off on that for now.

I am going to put together a new pc part list, not intel time and just go with a new system, and eventually down the line after I get the motherboard replaced on the intel system, either keep that for backup use or try and sell it and recoup my losses

  On 10/01/2025 at 14:07, Sharpstick68 said:

...should I still continue with the RMA for my processor with intel? or should I hold off on that for now.

Expand  

Unless you plan on having access to other parts to check the CPU with any time soon, you're just going to have to go with the information you have right now.

It's one of the CPUs affected by the bug, I assume it had been running on the older BIOS version for a good while before you recently updated it, and it became unstable until it no longer booted at all. So, it's not 100% for certain that the CPU is bad, but it's more likely than not. I'd RMA it.

I thought about something that I forgot/failed to mention when I originally made this thread. I think a day before, or on the day of the crash..my corsair cooler did start blinking red when running fortnite, and checing in iCUE that indicates the cooler is running in fail safe mode, and also the processor temp was up around lik 95C I believe while I had fortnite open. So I closed the game, restarted my computer because the cooler usually resets when I do that, but it was still blinking red, so then I just shut the computer down all the way and gave it like 5 mins for the heat to dissipitate and after I turned it back on again it was normal, and I didn't smell like a burning smell near the computer. I did notice though when I originally bought all the parts from micro center, one of the fins on the radiator is bent, I don't know if that had anything to do with it functioning correctly. But should I switch to a regular cooler? aio coolers I just never want to trust them again after all this that's happened..

 

20250111_091944.thumb.jpg.693771d780be0e1f41d2ab7a47058d1d.jpg

  On 11/01/2025 at 14:26, Sharpstick68 said:

I thought about something that I forgot/failed to mention when I originally made this thread. I think a day before, or on the day of the crash..my corsair cooler did start blinking red when running fortnite, and checing in iCUE that indicates the cooler is running in fail safe mode, and also the processor temp was up around lik 95C I believe while I had fortnite open. So I closed the game, restarted my computer because the cooler usually resets when I do that, but it was still blinking red, so then I just shut the computer down all the way and gave it like 5 mins for the heat to dissipitate and after I turned it back on again it was normal, and I didn't smell like a burning smell near the computer. I did notice though when I originally bought all the parts from micro center, one of the fins on the radiator is bent, I don't know if that had anything to do with it functioning correctly. But should I switch to a regular cooler? aio coolers I just never want to trust them again after all this that's happened..

 

20250111_091944.thumb.jpg.693771d780be0e1f41d2ab7a47058d1d.jpg

Expand  

It's fine, you only need to worry if the radiator starts leaking 😂 A little dent here and there is really nothing to worry about. I have them too.

  • Like 2

Also I did contact MSI and let them know what was going on, and they told me I can send it in to them, and it would cost $45 dollars to replace the cpu socket, which I think is amazing. All of this though just makes me never want to ever build a computer myself after what all has happened. Yea I know how to install RAM, a video card, some hard drives..but obviously, I do not know how to remove a aio water cooler block.

  On 12/01/2025 at 14:06, Sharpstick68 said:

Also I did contact MSI and let them know what was going on, and they told me I can send it in to them, and it would cost $45 dollars to replace the cpu socket, which I think is amazing. All of this though just makes me never want to ever build a computer myself after what all has happened. Yea I know how to install RAM, a video card, some hard drives..but obviously, I do not know how to remove a aio water cooler block.

Expand  

As long as you learn from it :)

Just wanted to give an update on what's going on

I started my RMA with Intel on Jan 08, 2025..took them 3 days to get my CPU, validated it same day they received it, and also sent out my replacement that day which is arriving today (Jan 17, 2025) so cudos to Intel. MSI should be receiving my motherboard today and hopefully I get that back soon after they inspect and hopefully repair the 2 bent pins that I told them about, which they said would cost me $45 dollars to replace the cpu socket. I thought about starting to look for a DDR5 motherboard since I'm finding alot of places don't have them any more and people that do are third-party/scalpers over-pricing them due to availability or being phased out, who knows.

One last thing I forgot, when I was disconnecting my aio cooler, a cable accidentally snapped off, it was like so light-weight and snapped so easy, it said TKG 2510 on it and it was like a 3-hole cable..I don't know if that is necessary for the AIO to work, do I need to get a whole new cooler?

  • Like 2
  On 17/01/2025 at 14:56, Sharpstick68 said:

One last thing I forgot, when I was disconnecting my aio cooler, a cable accidentally snapped off, it was like so light-weight and snapped so easy, it said TKG 2510 on it and it was like a 3-hole cable..I don't know if that is necessary for the AIO to work, do I need to get a whole new cooler?

Expand  

That might be power for the pump..

  On 09/01/2025 at 06:42, Sharpstick68 said:

Ok, I have already removed the cpu which it was my first time ever doing so in my entire life, I've always been nervous about damaging the cpu in the proccess

Expand  

On newer CPUs, where the pins have been relocated from the processor to the motherboard, you have to be more cautious of the socket on the motherboard than the processor. The processor will be fine.

Obviously, in the reverse, where the processor has the pins, you have to be more cautious of the processor.

  On 17/01/2025 at 16:38, Sharpstick68 said:

yea that is what I am trying to figure out, if it's for the pump, the case fans or what..and if I need a new cooler or not

Expand  

Well, where does this cable come from? That normally tells you what it is for. If it connected up to the AIO header, then it probably is the pump. But if it goes to a fan, that's your answer.

The radiator/pump unit is connected via a 24-pin cable to the control unit ("Commander CORE").

The control unit gets power via a SATA power connector.

The fans all plug into the control unit via standard 4-pin fan connectors.

To keep the motherboard from complaining about a lack of CPU fan, the control unit has a 3-pin connector that goes to the motherboard with a single tachometer (fan RPM) wire. This is the most delicate cable since it is just one wire. You can see it in the installation video here.

If it's the tach wire that broke, then the motherboard may beep angrily at you, thinking there is no CPU fan. There might be an option to disable this in the BIOS/UEFI, or you could connect a different fan to the CPU fan header on the motherboard (like one of the chassis fans) to keep it happy. However, if the Corsair cooler ever fails or becomes disconnected, then you won't get a warning beep to let you know. That's not ideal, but it's not the end of the world either. Modern CPUs do have internal thermal protection, and will power off if they overheat.

Alternatively, someone with the proper skills may be able to repair the wire.

  On 17/01/2025 at 23:26, ShadeOfBlue said:

The radiator/pump unit is connected via a 24-pin cable to the control unit ("Commander CORE").

The control unit gets power via a SATA power connector.

The fans all plug into the control unit via standard 4-pin fan connectors.

To keep the motherboard from complaining about a lack of CPU fan, the control unit has a 3-pin connector that goes to the motherboard with a single tachometer (fan RPM) wire. This is the most delicate cable since it is just one wire. You can see it in the installation video here.

If it's the tach wire that broke, then the motherboard may beep angrily at you, thinking there is no CPU fan. There might be an option to disable this in the BIOS/UEFI, or you could connect a different fan to the CPU fan header on the motherboard (like one of the chassis fans) to keep it happy. However, if the Corsair cooler ever fails or becomes disconnected, then you won't get a warning beep to let you know. That's not ideal, but it's not the end of the world either. Modern CPUs do have internal thermal protection, and will power off if they overheat.

Alternatively, someone with the proper skills may be able to repair the wire.

Expand  

 

So is it necessary to RMA the cooler to Corsair then or no? I honestly don't even like the RGB now that I've experienced it and I honestly would rather have good quality Notuca case fans instead

I don't know what RMA options you have for physical damage with Corsair. But assuming it is the tach wire that is broken, it should not affect the performance of the cooler. It only provides fan speed sensing to the motherboard.

Easiest thing is to plug one of the case fans (not one of the Corsair cooler fans) into the CPU fan connector on the motherboard. You can also go into the BIOS/UEFI and change the fan speed setting (otherwise it will be regulating the fan speed based on the CPU temperature).

If you really want to, you can replace any of the fans with suitable Noctua ones.

  On 17/01/2025 at 23:26, ShadeOfBlue said:

The control unit gets power via a SATA power connector.

Expand  

Actually, that's not true anymore. ?In the old days, yes, they did use that. Nowadays not so much.

  On 18/01/2025 at 04:04, Mindovermaster said:

Actually, that's not true anymore. ?In the old days, yes, they did use that. Nowadays not so much.

Expand  

This is a description of this user's specific hardware.

Small units can get away with being powered from a typical fan or pump header. Larger units such as OP's, running a pump and up to 6 fans plus LEDs, require a little more oomph.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • 2025 finally the Year of Linux? LibreOffice explains "real costs" of Windows 11 by Sayan Sen A big change is coming to Windows PCs as Microsoft will soon end support for systems and devices running on Windows 10. As such, the company, alongside its partners like AMD, Asus, and Dell, have begun urging users to embrace the "mandatory Windows 11 upgrade." The problem is that not every PC out there will be able to do so, at least not officially, as Microsoft had declared higher requirements for Windows 11 and thus many systems would be left out. Redmond's official stance for such situations is that users get a new computer by dumping their older system. There is another option users have: switching to Linux. Back in January, earlier this year, ESET recommended that users do that if they can not upgrade from Windows 10 to 11 or perhaps when they do not want to. Last month, KDE launched a new campaign dubbed "Endof10", which encourages users to make the jump. The project page explains several of the benefits of Linux over an unsupported Windows 10 system, like security and privacy, among others. And it also published another post earlier this month welcoming such "Windows 10 exiles". Now, The Document Foundation, maker of LibreOffice, has also joined in to support the Endof10 initiative. The foundation writes: "You don’t have to follow Microsoft’s upgrade path. There is a better option that puts control back in the hands of users, institutions, and public bodies: Linux and LibreOffice. Together, these two programmes offer a powerful, privacy-friendly and future-proof alternative to the Windows + Microsoft 365 ecosystem." It further adds the "real costs" of upgrading to Windows 11 as it writes: "The move to Windows 11 isn’t just about security updates. It increases dependence on Microsoft through aggressive cloud integration, forcing users to adopt Microsoft accounts and services. It also leads to higher costs due to subscription and licensing models, and reduces control over how your computer works and how your data is managed. Furthermore, new hardware requirements will render millions of perfectly good PCs obsolete. .... The end of Windows 10 does not mark the end of choice, but the beginning of a new era. If you are tired of mandatory updates, invasive changes, and being bound by the commercial choices of a single supplier, it is time for a change. Linux and LibreOffice are ready — 2025 is the right year to choose digital freedom!" To help users with the migration from Windows to Linux, The Document Foundation has laid out some key steps on how to proceed: Start by testing Linux and LibreOffice on a second partition of your PC (for individuals) or in less critical departments (for companies). Check the compatibility of your software configuration with Linux and LibreOffice; most office tasks can easily be transferred or adapted with minimal effort. Build documentation to learn how Linux and LibreOffice work and organise training if necessary. Find a consultant who can help with the migration process, such as someone certified by the Linux Professional Institute or The Document Foundation (for LibreOffice). The foundation stresses how "important" it is to "start immediately" with the transition. You can find the full details about the announcement here in the official blog post.
    • Why is it that some people think we have a tinfoil hat mentality, as you put it, just because we don't want AI on our devices? As for MS or any other company looking at everything, it seems to be the thing these days that companies want to know all about us. Can't even go shopping these days without being asked if you have some sort of card that tell them what you are buying and who you are.
    • Until the employer looks right though the AI created letter and notice it is AI created. You will be surprised how many can tell, there is something about an AI created letter that stands out to some people.
    • Snapchat brings new features, including auto-saving for public Stories by David Uzondu Snapchat, which recently expanded to watchOS after a decade, is rolling out new tools for its creators. The company says people are watching more content than ever, so these updates are meant to help creators get more out of that attention. The new features focus on a few key areas: making video editing less of a hassle, showing who is actually watching, and saving posts that used to vanish forever. Video editing on the platform has always been a huge problem. The tools are fine for quick clips, but they get messy if you try to do anything more complex. A new Timeline Editor for creators in the US is coming "soon" to fix this. It shows your video clips in a simple timeline, letting you cut and move parts around without wanting to pull your hair out. You can still add all the usual Lenses and music on top of these edits. For even quicker edits, a "Create a Video" template is now available globally for iOS users. The idea is simple: you look through your saved Memories, pick a handful of photos or videos, and then choose a song from the app's library. After you select a template, Snapchat mashes it all together into a single compilation video for you. But making videos is only part of the job. To help people see if anyone is paying attention, new insights are also available. These stats give a much better idea of how an audience behaves. Instead of just one giant view number, creators can now track "Returning Viewers." This counts how many people watched their content at least 12 times in the last month. Other metrics include the "Spotlight Average View Rate," showing what percentage of a video people finished. You can also see "Views by Traffic Sources," which tells you if people found you from the Discover page, search, or their own feed. Finally, there is a new "Auto-Save Stories to Public Profiles" feature. For years, the whole point of a Snapchat Story was that it was temporary. This new option, which is rolling out to creators globally, automatically saves public Stories to a creator's profile. Snapchat notes that the new feature "helps creators build a lasting collection of their best moments, giving fans a deeper look into their creative journey and making it easier to keep content alive, accessible, and meaningful over time."
    • I did not think it could be removed, all it does is remove the icon, co-pilot is still there as far as I know. Also don't forget the other apps it is in. What is needed is a simple thing to click to remove co-pilot and any AI rubbish from the computer, just like I can on my Mac.
  • Recent Achievements

    • One Month Later
      POR2GAL4EVER earned a badge
      One Month Later
    • One Year In
      Orpheus13 earned a badge
      One Year In
    • One Month Later
      Orpheus13 earned a badge
      One Month Later
    • Week One Done
      Orpheus13 earned a badge
      Week One Done
    • Week One Done
      serfegyed earned a badge
      Week One Done
  • Popular Contributors

    1. 1
      +primortal
      562
    2. 2
      ATLien_0
      256
    3. 3
      +Edouard
      163
    4. 4
      +FloatingFatMan
      156
    5. 5
      Michael Scrip
      109
  • Tell a friend

    Love Neowin? Tell a friend!