Hard Disk's Click of Death?


Recommended Posts

Dear friends,

I'm writing this thread based on my long personal experience with HDDs failures, and after I saw much threads about that "Click of death" in neowin and other forums, and most members simply reply: Your HD is dead, get a replacement!

Most of us believe that the important thing in this case isn't the hardware, but the data on it, but in this guide, I'm listing ways to recover the data from those clicking drivers, even fixing it at home, using certain methods, and you get 100% working drive again for coming years!

IMPORTANT NOTE: In this guide, I'm assuming that clicking sound is happened suddenly, not after a physical shock to the drive, in 90% of such case "a shock", something is broken in the HDD, and it can't be repaired using this guide, only a special data recovery center may do it for you, for a bunches of $s.

Ok lets get started, let's list common causes for "HDD clicking sound":

- Bad power supply or power connector.

- Defected Motherboard.

- Defected HD's board (that green board on it's back.

1- Bad power connector

This is the most common case, the power cable that connect the drive to the power supply is defected, or the power supply itself is dying, simply, the best solution is to swap power connectors, or replace the power supply. Do not ever try to repair the power connector because you may cause further damages.

2- Defected Motherboard

This is rarely happen, but if your motherboard have some problems, it may lead to that clicking of HDD, and you wont be able to boot using that drive, the best solution is to put your drive in a friend's PC or something, if it works there, then it's your motherboard. and you need to replace it.

3- Defected HD's board

Actually, this is the main point that made me write such guide, in most cases, unreliable power supply or a case of sudden, the board of the HDD fails. AFAIK, it can't be repaired, so what can you do?

Simply, find a physically defected drive of the EXACT SAME MODEL of yours, and using a screwdriver, get the board out of that drive, and replace it in your drive, and enjoy your drive working perfectly again! I'm assuming that you can find that exact board somewhere (from a friend's damaged HD, repair shop... etc), if you can't find any, and you think that your data is so important, just buy a new EXACT SAME MODEL hard disk like yours, and do the job with the new board!

Ok we're done! I heard that for physically defected hard drives, you can get it to work again by putting it in a freezer for some time then connecting it, I can't confirm if this works or not, because I didn't try it personally, but I experienced all of the methods above, and remember, it's NOT for physically defected drives!

Cheers :)

Link to comment
https://www.neowin.net/forum/topic/258406-hard-disks-click-of-death/
Share on other sites

1- Bad power connector

This is the most common case, the power cable that connect the drive to the power supply is defected, or the power supply itself is dying, simply, the best solution is to swap power connectors, or replace the power supply. Do not ever try to repair the power connector because you may cause further damages.

with this though your machine would freeze because the alctual drive will be re-booting. Due to loss of power.

Never, EVER do what this kid did. It is so stupid it hurts. :no:

https://www.neowin.net/forum/index.php?showtopic=258035&hl=

585115992[/snapback]

IF, you meant by the kid is me, then you didn't understand a letter of my post because I never said open the HD! I said replace its board, which can be replaced easily without actually openning the drive!

IF, you meant by the kid is me, then you didn't understand a letter of my post  because I never said open the HD! I said replace its board, which can be replaced easily without actually openning the drive!

585116109[/snapback]

My post had absolutely nothing to do with you. I apologise if offence was taken. :)

1- Bad power connector

This is the most common case, the power cable that connect the drive to the power supply is defected, or the power supply itself is dying, simply, the best solution is to swap power connectors, or replace the power supply. Do not ever try to repair the power connector because you may cause further damages.

In my experience this is the most common also. I went thought two dodgy power supplies, replacing each when the HDD's would randomly wind down (click) while using my computer. I finally learnt a lesson and bought an antec true blue 480w. Hasn't happened since.

Ok we're done! I heard that for physically defected hard drives, you can get it to work again by putting it in a freezer for some time then connecting it, I can't confirm if this works or not, because I didn't try it personally, but I experienced all of the methods above, and remember, it's NOT for physically defected drives!

The freezer method DOES work, but once you do it, back up quickly because you don't get a second chance. My mate has used this method successfully numerous times on customers HDD's. :)

Cheers for the guide, a lot of people should be aware of this before giving up on their HDD's.

Nice Guide Tantawi,

Maybe you could include some images for people at what to look for with defective ribbons and power connectors (I remember seeing a few pictures of burnt out headers and tips about various programs on some sites), It also would be good to point out the fact that alot of these "ticks" are different .

there are certainly things like S.M.A.R.T and various drive tools to help you before the event occurs :yes: Prevention of data loss and proper back up methods are a big part of this ;)

(and for people with seagate drives many of them will actually make a beep when disconnected from the power.)

I think I have #3. I've heard my 4GB HDD on my old computer click annoyingly for around umm, three or four years. But it also could be #2, because I've had the motherboard for seven years, although I did clean it out. It couldn't be the PSU because I've just got a new one after the old one broke.

And by the way, although my sound does no harm, when it's swapping RAM, it clicks sooo much and is so annoying! I think I'll go crazy soon, but luckily, I'm getting anew computer, yay!

Nice list Tantawi :)

I'll just add a few more points of how important it is to backup the data as soon as possible.

I've had experience with at least 30 HD's so far, not all mine but friend's aswell.

Some hard drives make a certain single click noise when the PC boots up, no biggie. But if hear a new sound or repetitive clickings, that's certainly not good.

My advice, the first time you hear a click, drop everything and backup immediately, to another HD if possible because you never know the problem if exists can really detoriate rather quickly. First copy the most important files on the HD, then creating an Image of the drive is best or do a drive to drive copy to a new drive, so you don't have to go and re-install everything or risk chance of forgetting something. Do a HD scandisk full surface scan, if no bad sectors are found, yes it might be the power cable to the HD or a bad connection, unplug and re-plug all HD cables (that has actually helped once), or replace the cables. If all is good you can also defrag the drive so it won't work as hard.

If bad sectors are found and you hear more clicking, with a backup of the original drive on some other drive or media. Say you have a spare HD which you copied the image to (Symantec Ghost is very recommended though there are free utils), or drive down to the store and buy a new HD and make an image(or drive to drive copy), now consider sending the original drive to the manufacturer for a replacement, I mean why worry get nice new HD instead. You'll get a free(you pay to ship the drive) replacement if the drive is less than 3 years old, depending on the manf. of course. Goto their website and get an RMA, they'll give you all the info you need to know. Before sending out the drive, format and write 0's and 1's to the drive(special utils that actually erase the data for sure) . Many people actually think just format or fdisk erases the data for sure, not really.

Just a note to those newbies out there, never try to open the HD casing so the platter is revealed! First off , you void the warranty and If a single speck of dust lands on the platter, good luck and don't blow to get rid of it ;)

Dear friends,

I'm writing this thread based on my long personal experience with HDDs failures, and after I saw much threads about that "Click of death" in neowin and other forums, and most members simply reply: Your HD is dead, get a replacement!

Most of us believe that the important thing in this case isn't the hardware, but the data on it, but in this guide, I'm listing ways to recover the data from those clicking drivers, even fixing it at home, using certain methods, and you get 100% working drive again for coming years!

IMPORTANT NOTE: In this guide, I'm assuming that clicking sound is happened suddenly, not after a physical shock to the drive, in 90% of such case "a shock", something is broken in the HDD,? and it can't be repaired using this guide, only a special data recovery center may do it for you, for a bunches of $s.>

Ok lets get started, let's list common causes for "HDD clicking sound":

- Bad power supply or power connector.

- Defected Motherboard.

- Defected HD's board (that green board on it's back.>

1- Bad power connector>

This is the most common case, the power cable that connect the drive to the power supply is defected, or the power supply itself is dying, simply, the best solution is to swap power connectors, or replace the power supply. Do not ever try to repair the power connector because you may cause further damages.

2- Defected Motherboard>

This is rarely happen, but if your motherboard have some problems, it may lead to that clicking of HDD, and you wont be able to boot using that drive, the best solution is to put your drive in a friend's PC or something, if it works there, then it's your motherboard. and you need to replace it.

3- Defected HD's board>

Actually, this is the main point that made me write such guide, in most cases, unreliable power supply or a case of sudden, the board of the HDD fails. AFAIK, it can't be repaired, so what can you do?

Simply, find a physically defected drive of the EXACT SAME MODEL of yours, and using a screwdriver, get the board out of that drive, and replace it in your drive, and enjoy your drive working perfectly again! I'm assuming that you can find that exact board somewhere (from a friend's damaged HD, repair shop... etc), if you can't find any, and you think that your data is so important, just buy a new EXACT SAME MODEL hard disk like yours, and do the job with the new board!

Ok we're done! I heard that for physically defected hard drives, you can get it to work again by putting it in a freezer for some time then connecting it, I can't confirm if this works or not, because I didn't try it personally, but I experienced all of the methods above, and remember, it's NOT for physically defected drives!

Cheers:))

585115815[/snapback]

Edited by Techo

Am I the only one that hasn't had a HD go bad on me? Have a computer here that is probably 6 years old and it's still running on the original hd. I've been running a raid 0 setup using 2 fairly old hds, maybe 3-4 years, and they are still going strong. What causes the click of death? Frequent use? heat? excesive defrags and formats?

Hmm

Most of what you say is just common sense.

And as for opening up the actual HD, some HD manufacturers have special screws in which a normal PK or Phillips head will not fit. Is almost like a T6 screwdriver needed.

And some people may have old HD which may have to be acquired from ebay or alike if they were to switch boards.

Or even better, back up your data via DVDrom or even CD roms and also try Norton Ghost dos and use its high compression and burn to disks a image of the drive in question.

Maybe you shouldve mentioned that.

Well touch wood boys and girls, no sooner did I make this post then a cpl days later what do I hear one early morn.....the clicking of the HDD. My apologies too, I have heard this sound before when my last HDD died.

Now given that this is the 2nd hdd on its way to death in about a year, im inclined to believe its the motherboard or powersupply. Is there any specific way I can check this really? I suppose all I can do is change the power connector or supply, and if it still does it, assume its the motherboard?

I mean two in a year, from different manufactuers too, im inclined to believe its not the hdds themselves.

i had some clicking sound,only reason i had it before i replaced it was cuzz i kept hot swapping the drive out then on the 3rd time it screwed up,killed my 2000 partition and crippled my xp partition so out of 80GB i was left with 62GB and clicking sound,took it to a fellow i get stuff from and he said it's something wrong with the drive and maybe send it back(where i got it from i would have to travel 8 hours to get to where i got it and i don't even drive and i doubt there is still a warrenty on it)

reminds me of my maxtor 200gb drive that suddenly stopped working. no click, i had just plugged it into my xox, formatted it, and then locked disc, then it froze and the drive never worked again, just makes a odd beep(like in a video gameor something) i put it in the freezer but havent tried it again.

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • How to Do More with Less: Future-Proofing Yourself in an AI-driven Economy —was $28 now FREE by Steven Parker Claim your complimentary copy (worth $28) of "How to Do More with Less: Future-Proofing Yourself in an AI-driven Economy" for free, before the offer ends on June 30. Description In today’s workplace, headlines about artificial intelligence can feel overwhelming. With headlines swinging between promises of utopia and warnings of mass unemployment, for most knowledge workers, the truth feels unclear. In this book, Sharon Gai cuts through the noise. Drawing from real-world examples and global insights, she explains how AI is reshaping the way we work—without hype or fearmongering. Instead of choosing between blind optimism or outright pessimism, she offers a practical, balanced perspective that helps readers make sense of the rapidly evolving AI landscape. You’ll learn how to: Reskill and future-proof your career in the face of AI disruption Identify which parts of your role can be automated, and which require human creativity and judgment Use proven frameworks to evaluate AI’s impact on your work and your organization Apply actionable tips and tools to boost productivity, make smarter decisions, and do more with less Gain clarity as a parent, leader, or professional navigating what this means for the next generation Whether you’re an employee anxious about your future, a parent concerned about your children’s opportunities, or a leader managing a lean team with tight budgets, this book provides the strategies and mindset you need to adapt so you can stop worrying and start preparing. How to download for free Please ensure you read the terms and conditions to claim this offer. Complete and verifiable information is required in order to receive this free offer. If you have previously made use of these offers, you will not need to re-register. Was $28, but is now FREE | Below free offer link expires on June 30. How to Do More with Less: Future-Proofing Yourself in an AI-driven Economy The below offers are also available for free in exchange for your (work) email: The Vibe Coding Playbook: Building Your Tech Business with AI ($35 Value) FREE - Expires 6/23 The Persuasion Engine: How Any Business Can Use AI-Powered Neuromarketing to Understand and Win Customers ($28 Value) FREE - Expires 6/24 How to Do More with Less: Future-Proofing Yourself in an AI-driven Economy ($28 Value) FREE - Expires 6/30 Cloud Security Fundamentals: Building the Foundations for Secure Cloud Platforms ($131.95 Value) FREE - Expires 7/1 The Complete Free AI Learning: Master ChatGPT, Claude, Gemini & More ($21 Value) FREE How to Build an AI Design Workflow with Gamma ($21 Value) FREE The Ultimate Linux Newbie Guide – Featured Free content Python Notes for Professionals – Featured Free content Learn Linux in 5 Days – Featured Free content Quick Reference Guide for Cybersecurity – Featured Free content We post these because we earn commission on each lead so as not to rely solely on advertising, which many of our readers block. It all helps toward paying staff reporters, servers and hosting costs. Other ways to support Neowin The above deal not doing it for you, but still want to help? Check out the links below. Check out our partner software in the Neowin Store Buy a T-shirt at Neowin's Threadsquad Subscribe to Neowin - for $14 a year, or $28 a year for an ad-free experience Disclosure: An account at Neowin Deals is required to participate in any deals powered by our affiliate, StackCommerce. For a full description of StackCommerce's privacy guidelines, go here. Neowin benefits from shared revenue of each sale made through the branded deals site.
    • Microsoft admits one of the most crucial Outlook features is currently broken by Sayan Sen Microsoft is making some decent progress when it comes to Windows 11. Recently we have confirmed reports of some rather useful improvements landing in the next version of the OS, 26H2, wherein GPU driver TDR crashes may finally be fixed, plus the company is also allowing users to disable web content on the Search. On the Outlook front though things have not been so rosy. Last month in May we reported several problems affecting basic functionalities on the app. These included a problem where documents would open blank or corrupt themselves. Following that, Quick Steps, a very useful feature, would no longer work correctly, and finally, Microsoft acknowledged a problem wherein images would fail to load up properly inside the email. Microsoft had resolved those bugs later and almost exactly a month after we reported on them, the company has now admitted a new similarly basic issue, this time on Macs. Users recently started noticing that Outlook would no longer display email threads properly as the original message itself was not displayed. An affected user Tsoumpas, C (ngmb) nicely described the problem in a forum post they made on Microsoft's site. They wrote: "Description of the issue: After updating Outlook for Mac [Version 16.110 (26061317)] on 18/6/2026, replying to any email no longer includes the original message in the reply window. Prior to the update, replies correctly contained the original email text below my response. Expected behavior: The original message should be included in the reply, as in previous Outlook versions and according to the configured reply settings. Actual behavior: The reply window contains only a blank composition area (or only my response), with none of the original email text included." Obviously this must be a highly frustrating for users as noted by several in that thread. The post, at the time of writing, has also been upvoted by more than 40 users indicating that is a fairly widespread bug. Thankfully Microsoft seems to have acknowledged the problem right around that time as it opened a new issue on its official website. In the support article, the company recommends switching to Outlook for Mac from the legacy app, where the problem appears to be happening.
    • PotPlayer 260622 by Razvan Serea PotPlayer is an extremely light-weight multimedia player for Windows. It feels like the KMPlayer, but is in active development. Supports almost every available video formats out there. PotPlayer contains internal codecs and there is no need to install codecs manually. Other key features include WebCam/Analog/Digital TV devices support, gapless video playback, DXVA, live broadcasting. Distinctive features of the player is a high quality playback, support for all modern video and audio formats and a built DXVA video codecs. A wide range of subtitles are supported and you are also able to capture audio, video, and screenshots. A comprehensive video and audio player, that also supports TV channels, subtitles and skins. Its been described on the Internet as The KMPlayer redux, and it pretty much is. Daum PotPlayer 260622 (1.7.22963) changelog: Removed Kakao TV Added pause function when navigating via the navigation bar Significantly improved internal stability Fixed an issue where colors appeared strange during RGB24 processing Improved playback for some HTTP streams Improved sync processing for the built-in audio renderer Fixed an issue where certain MP4 files behaved abnormally during playback Download: Daum PotPlayer (64-bit) | 54.7 MB (Freeware) Download: Daum PotPlayer (32-bit) | 61.1 MB View: Daum PotPlayer Home Page | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • Tixati 3.44 is out.
  • Recent Achievements

    • Dedicated
      tuben earned a badge
      Dedicated
    • Week One Done
      mnsgroup earned a badge
      Week One Done
    • Conversation Starter
      sumytbe earned a badge
      Conversation Starter
    • One Year In
      B4dM1k3 earned a badge
      One Year In
    • One Year In
      DarkWun earned a badge
      One Year In
  • Popular Contributors

    1. 1
      +primortal
      522
    2. 2
      +Edouard
      199
    3. 3
      PsYcHoKiLLa
      94
    4. 4
      Michael Scrip
      82
    5. 5
      neufuse
      69
  • Tell a friend

    Love Neowin? Tell a friend!