Recommended Posts

Hi

Just after a quick bit of help. I've been given a Compaq Armada M300. Its a P3 somthing or other, only problem is there is a bios start up password, which means its pretty much useless (hence why it was given).

I've tried searching round the net and the only thing i've come up with it removing the bios battery and shorting the 2 pins; which didn't work. I've also seen on some toshibas it can be done by shorting various pins on the parallell port, but found northing for the compaq. So if anyone have any ideas, I'd be most greatful :)

Cheers

Huw

Link to comment
https://www.neowin.net/forum/topic/270482-bios-password/
Share on other sites

Taken from another forum.

I know that this will work with a M300 because I have done it successfuly.

Unplug the power cord. Remove the main laptop battery, if any. Look at the bottom of the laptop you will see a small, almost round door. Open it and find the little battery with two wires soldered on each side.
disconnedt the battery, only the positive one will suffice. Now short the wires, connect them together for a few seconds and release. Then hold the power button down while you pull the reset key (on the edge of the laptop) a few times. ( You have not connected the power cord yet). Now wait about 15 minutes. Connect the power cord and turn the laptop on. Wait for the complete boot. Success will show by a blinking cursor at the top right hand side.
The CMOS that holds the power on password is clear now. Turn off the laptop, put the friggin' little battery together, connect the power cord and reboot. While you are tapping on F10 key to get into bios. Set it to factory default and exit.
You are done. If windows starts to load but it asks you for another password it is another story. You need to format the hard drive and reinstal windows.
Enjoy the lil laptop now, dude.
Babak

Dunno if that will help.

Link to comment
https://www.neowin.net/forum/topic/270482-bios-password/#findComment-585281155
Share on other sites

Well, taking the battery out etc, worked :) so the password is removed. just one more problem now, it seems if i turn the laptop off after it being on for more than a few minutes it will refuse to turn back on. However if i come back the next morning the process is repeated :s and the laptop springs to life as soon as i plug the power cord in. Annoying, so close, yet so far. Ideas? :blink:

Cheers

Link to comment
https://www.neowin.net/forum/topic/270482-bios-password/#findComment-585291757
Share on other sites

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • About bloody time. I have got PRs with hundred of files and the Web UI just struggling to even load the pages.
    • I wonder if it was applying secure boot certificates/dbx files?
    • I recently tried edge. It seems a lot better. A lot of the junk in it is gone. It seems less bloated and snappy.
    • Lethal fake phone chargers are still being sold on Amazon and eBay, UK watchdog warns by Paul Hill Credit: Pexels The UK consumer rights organization, Which?, is claiming that “potentially lethal knock-off chargers” are still being sold on online marketplaces seven years after it exposed the danger of these chargers. In its latest investigation, it bought 15 USB phone chargers from several online marketplaces and found they were missing key information, meaning they cannot be legally sold in the UK. Which? bought the 15 chargers from seven online marketplaces. These were Amazon (including Amazon Haul), AliExpress, B&Q Marketplace, Debenhams Marketplace, and eBay. It said that the chargers were so badly made that anyone using them was at risk of electric shock. Over half the chargers also posed fire and explosion risks. Of the chargers purchased, one was a fake Apple USB-C 35W power adaptor charger. To confuse buyers, the box was branded with an Apple logo, but testing found it to be a fake. Further testing picked up arcing sounds after 10 seconds of use, where a current jumps between two parts of the electrical circuit, which can cause fires, explosions, or electric shock. The manufacturers of this particular charger also put modeling clay inside it to make it feel more weighty, robust, and genuine. Not all of the chargers were technically faulty; however, some were missing key packaging, markings, and documentation, meaning they can’t be sold in the UK legally. Which? said that it is now campaigning alongside a coalition of safety groups and businesses for new laws that make online marketplaces responsible for ensuring the safety of products that they choose to list on their websites. It also said the government needs to start using powers under the Product Regulation and Metrology Act, which was adopted last July, to impose safety requirements on online marketplaces via secondary legislation, but so far, there have been delays. No matter what country you are in, be sure to properly research what you are buying and only buy authentic chargers to prevent fires. You can read more about Which?’s research here.
    • Visual Studio finally gets long-awaited feature that developers will love by Usama Jawad Visual Studio Code is Microsoft's popular, lightweight, open-source code editor, it is actually Visual Studio that is the company's flagship integrated development environment (IDE). Although the IDE already offers a boatload of useful features for developers, Microsoft has finally introduced a long-requested capability that will be loved by many. While developers have already been able to create Git pull requests (PRs) directly within Visual Studio for the past couple of years, it had not been possible to review a PR without switching to the browser, until now. Microsoft revealed in December 2025 that it is working on UX that enables developers to do just that, and fast-forward to June 2026, and Visual Studio finally has native capabilities to open and inspect a PR, discuss feedback, and wrap up the review, all without switching to the browser. This integration works for both GitHub and Azure DevOps (including on-prem). Developers have access to multiple surfaces to open a PR, including Git Repository, Git Changes, and the Git menu in Visual Studio. Once you open a PR, all the important details will be immediately visible to you, from where you can navigate to various levels of granularity and branch states, depending on the reviews that you are engaged in. As you would expect, you also get a diff view that enables you to see code changes inline or side-by-side in a separate panel. You can also review commit-by-commit. Additionally, this UX fosters collaboration as you can leave comments, reply to threads, and resolve conversations easily. Naturally, you can also leverage Copilot to apply a code suggestion to fix a potential issue. When you are done, you have the ability to approve, complete, and merge the PR. This is a pretty major feature as it has been requested heavily for the past few years. You can try it out in Visual Studio 2026 version 18.7, made available here recently. Microsoft plans to enhance this experience further in future releases with comment filtering, a timeline of PR activity, and more.
  • Recent Achievements

    • Week One Done
      Timaximus earned a badge
      Week One Done
    • One Month Later
      Timaximus earned a badge
      One Month Later
    • Rookie
      FBSPL went up a rank
      Rookie
    • First Post
      davidbazooked earned a badge
      First Post
    • Week One Done
      davidbazooked earned a badge
      Week One Done
  • Popular Contributors

    1. 1
      +primortal
      499
    2. 2
      PsYcHoKiLLa
      174
    3. 3
      +Edouard
      160
    4. 4
      Steven P.
      84
    5. 5
      ATLien_0
      75
  • Tell a friend

    Love Neowin? Tell a friend!