WPA Encryption Explained


Recommended Posts

When you have a wireless network, it is your responsibility to make it as difficult as possible for someone else to gain access to it. After all, if someone does get in they can find out what your surfing, gain access to your computers and mess with router settings...or just use your internet connection.

Disabling SSID broadcasting and using MAC filtering is great, but can't stop someone from sniffing your traffic. WEP encryption provies a basic level of encryption, but can be cracked in under 10min.

So if you want a secure wireless network, there isn't a way around it, you need to use WPA.

Requirements

You need hardware and/or firmware/drivers that allow the use of WPA. Every wireless-G hardware out there has some form of WPA on it, but a firmware or driver update can get WPA on your older wireless-b equipment as well. Hardware that has been sold before 2003 generally need to be replaced.

Different Types

WPA Radius Authentication - Your typical home user wont use this, unless you want to setup a radius server. This server works with WPA to pass different keys to each user. I'm not going to go into how to set this up.

WPA PSK - PSK stands for Pre-Shared Key and is most commonly used by home users. The user must have a certain password to enter the network. PSK can be used with either AES or TKIP, depending on what your hardware can support. It is important that you choose a strong password to prevent against dictionary attacks.

AES - An algorithm that requires special hardware support to use. It is stronger, but a firmware/driver update won't get you AES.

TKIP - This system changes the key every specified amount of time to prevent cracking attempts. You can usually adjust how often it changes in the router/AP settings. This does not mean it changes your password, just the key.

WPA2 - The new WPA standard that uses a stronger algorithm, but is not backwards compatable with older hardware.

Making sure you got the software

Being that WinXP is the only OS that officially supports WPA2, you need to rely on 3rd party vendors for support, which is usually delivered.

Most of the time, when you install a driver for the wireless card, a special WPA driver will be installed with it. You can see it by going into the network/dialup connections in the control panel and looking at the properties of the card. It might be called something like "AEGIS WPA Protocol" or "WPA Security Protocol". Note that you cannot install updates to these protocols seperately from the drivers, your card requires specific WPA protocols to work.

post-38325-1117752184.jpg

Your router should have options for WPA in it's settings. If it does not, a firmware update could allow WPA to be enabled. Check the router's webpage to see if there is one.

If you do get a firmware update that enables WPA, I highly recommend that you restore your router's settings to factory default after upgrading the firmware. If I had known to do that I woulda saved myself a lot of trouble. :pinch:

Setting it up

First connect to the router with a patch cable rather than wirelessly. Setting up the router is easier that way. Login the router, go to the wireless security part. WPA-PSK is the type of encryption you want to use. After selecting PSK, you might get an option to either use AES or TKIP. If you had to upgrade any software to get WPA, then you probably have to use TKIP since AES requires hardware that natively supports WPA. After the selections have been made, you must choose a passphrase. Try to have it in the range of 10 to 25 characters. Once the passphrase is set, enter the same information in the wireless network card and you should be set.

post-38325-1117752250_thumb.jpg

Troubleshooting...

If WPA wont work:

1) Make sure that you have all the types and the passphrases matched exactly.

2) Try turning off/on the router or restarting.

3) If you are using the wireless config utility that comes with WinXP, try using the one that came with the card instead. You can set it by going into the properties of the network connection and unchecking "use windows to configure my wireless settings"

post-38325-1117752267.jpg

4) Sometimes using obscure characters like ąĈ??? can work against you in the passphrase.

5) If signal strength is lower than 9dB, then the connection is flaky with WPA.

6) Check to make sure the router is on fire. Fires usually interfere with the router's function.

7) If there are other wireless networks on the same channel in your area, change the channel to some different value.

8) Avoid generic drivers and firmware.

Link to comment
https://www.neowin.net/forum/topic/327471-wpa-encryption-explained/
Share on other sites

  Relativity_17 said:
Is there any software available for Windows that can tell whether you've successfully disabled SSID broadcasting on your router?

586007665[/snapback]

No, that requires the wireless utility that comes with your wireless card. All utilties come with a thing that views available wireless networks. Good adapters can show all the wireless networks in the area, if they have encryption, their signal strengh and their network name (or lack thereof). I think you can trust that SSID broadcasting is disabled and as long as you didn't leave it at "netgear" or "linksys", you're fine.

Considering that 3 of my neighbours have unencrypted networks, I'm not all too worried about someone getting into my network. The computers themselves are only open to each other, since their IPs are statically assigned from the router.

I'll look into it later on during the summer though... just for kicks.

Just a quick tip if your card does not support WPA look for the chipset that the card is and look on the internet for a company (like Dlink or Netgear) that uses the same chipset that does support WPA in there driver, install there driver over your card and you now have all there features.

My card an Asus 802.11G with only WEP 128bit encryption is convinced its a D-Link card and I now have WPA WPA-PSK WEP and so on.

  WinMacLin said:
Just a quick tip if your card does not support WPA look for the chipset that the card is and look on the internet for a company (like Dlink or Netgear) that uses the same chipset that does support WPA in there driver, install there driver over your card and you now have all there features.

My card an Asus 802.11G with only WEP 128bit encryption is convinced its a D-Link card and I now have WPA WPA-PSK WEP and so on.

586030693[/snapback]

Indeed :) Here's a link that might be useful to some. i.e. Toshiba Wireless LAN Adapter users can simply download the latest Agere driver.

  • 2 weeks later...
  kaffra said:
nice guide, i just got my netgear wireless router today. So wpa is better to have then wep?

586081494[/snapback]

Tons better. Wep can be cracked in like 15min tops. WPA is a lot stronger so long as you have a good password.

  Quote
Does the user have to always key in a password to access the network(if wpa is used?)

No.

Thanks for this guide, but I was wondering if you knew anything about steps to fix another (seemingly common) problem.

I recently set up a home wireless network in my fiance's parents' house, and set up with WPA-PSK. The router was a Linksys, I can't recall the exact model off the top of my head, but it was 802.11b only. (The notebook is capable of G, but for their purposes, that isn't really necessary, and the B router was $5 after rebate at Best Buy.)

The notebook is a Toshiba Satellite (don't remember the model either, sorry) with integrated B/G wireless, and was purchased in July of 2004. The notebook has successfully logged onto other WPA-PSK networks without having this problem. (There is a small coffee house with wi-fi that uses PSK we have connected in)

Logging in itself isn't the problem, however, every so often (probably when the key is reset), the connection is dropped, and we have to manually reconnect. Right now, the network is set to WEP, but they would really prefer to have WPA, and we cannot figure out how to correct this issue.

Just wondered if anyone had any ideas of how to start troubleshooting this, thanks!

Edit: Used TKIP when setting up

Edited by marshallbanana
  marshallbanana said:
Logging in itself isn't the problem, however, every so often (probably when the key is reset), the connection is dropped, and we have to manually reconnect. Right now, the network is set to WEP, but they would really prefer to have WPA, and we cannot figure out how to correct this issue.

586093189[/snapback]

Well your in luck because I had just about the exact same problem, with almost the same hardware (linksys router + toshiba satellite). After upgrading the firmware of the router itself, I switched to WPA, but the connection keeped dropping. I found out, after much difficulty, that it was caused by the router switching between WPA and WEP. Resetting the router settings fixed the problem. Hopefully it will fix it for you as well.

Well, WPA-PSK was available on the router without a firmware update, so I haven't done so. Would it be a good idea to try this first?

I'm not sure that resetting the router settings will do much, since the only settings changed out of the box were those concerning the SSID and setting up the encryption. I suppose it's worth a try :D

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Isn't the CPU used to calculate the parity for the RAID? If so, the combination of SSDs and 10GBe might make the CPU more important
    • yeah GSMA began working to enable end to end encryption between android and iphone last year and apparently a new standard was developed. apple has said that they would implement this in "future software updates" but i haven't heard anything since march, the time this was all reported on. shortly after, i read on forbes that the FBI suggests not sending texts between iphone and android because they're unencrypted. i use signal to chat with my wife but i'd rather just use messages tbh (she has an iphone), i'm not really a 3rd party guy haha
    • Well, I did not like the trailer for the project he went to work on also, but why do you think he should waste time with this… did you love the season 2? Maybe I am missing out after the crap I saw in first season ep1-3? I love the first last of us game… while not the BEST it was one of the games that I will remember for the EXPERIENCE it game me… last of us 2 was not on the same level at all and the show🤔 complete miss in my experience of the first few level
    • They're likely moving all resources to other things. Clearly Windows is not important to them.
    • Image Uploader 1.4.3 Build 5352 by Razvan Serea Image Uploader is a free and open-source program for Windows that that allows you to effortlessly upload images, screenshots, and various files to a wide array of hosting services. With its capability to capture selected screen areas, it promptly uploads content to image hosting services, while also offering the convenience of automatically copying the URL to your clipboard. Key Features of Image Uploader: Upload to Multiple Hosting Services Image Uploader supports uploading images and files to over 30 popular hosting services. Additionally, it can upload directly to your own FTP, SFTP, or WebDAV server. After upload, the tool automatically generates sharing codes in HTML, BBCode, and Markdown, with support for custom output templates tailored to your needs. Video Frame Grabbing and Screenshot Tools You can extract multiple frames from video files in a wide range of formats including AVI, MP4, MKV, WMV, and more. It supports both system-installed codecs and built-in ones. The extracted frames can be uploaded individually or compiled into a single mosaic image. It also includes screenshot capabilities for the full screen or selected regions, along with a simple image editor for annotations, highlights, and blurring. Advanced Integration and Usability Image Uploader supports drag-and-drop, clipboard monitoring, and can be accessed via Windows Explorer’s context menu. It also features URL shortening, multi-account support, reuploading, and the ability to upload images embedded in text while retaining formatting. The app is available in several languages, including English, Russian, Turkish, Korean, Arabic, and more. Image Uploader 1.4.3 Build 5352 changelog: New Features Screen Recording: Added two powerful capture methods: DirectX (Desktop Duplication API) FFmpeg-based recording Expanded Hosting Services: Added support for new file hosting platforms: TeleBox (linkbox.to) take-me-to.space ranoz.gg webshare.cz lobfile.com imgpx.com freeimghost.net radikal.cloud anonpic.org fotozavr.ru imgtr.ee thumbsnap.com 8upload.com filemail.com Others Video Uploads: Added Flickr.com support for video uploads Localization: New French translation added Context Menu: Added "File Information" option to video file context menus DPI Support: Improved support for: Screen DPI changes Mixed-DPI multi-monitor setups Improvements Disabled application window animations during screenshot/screen recording initiation Updated API and documentation Improved overall stability Bug Fixes Fixed network client error that could cause application crashes Resolved unauthorized startup registration issue Fixed upload functionality for pixeldrain.com Restored tray icon balloon notifications visibility Various minor bug fixes Download: Image Uploader 64-bit | Portable 64-bit | ~16.0 MB | (Open Source) Download: Image Uploader 32-bit | Portable 32-bit | ~15.0 MB Download: Image Uploader ARM64 | Portable ARM64 | ~11.0 MB Links: Image Uploader Home Page | Screenshot | GitHub Get alerted to all of our Software updates on Twitter at @NeowinSoftware
  • Recent Achievements

    • Reacting Well
      SteveJaye earned a badge
      Reacting Well
    • One Month Later
      MadMung0 earned a badge
      One Month Later
    • One Month Later
      Uranus_enjoyer earned a badge
      One Month Later
    • Week One Done
      Philsl earned a badge
      Week One Done
    • Week One Done
      Jaclidio hoy earned a badge
      Week One Done
  • Popular Contributors

    1. 1
      +primortal
      431
    2. 2
      ATLien_0
      157
    3. 3
      +FloatingFatMan
      149
    4. 4
      Nick H.
      64
    5. 5
      +thexfile
      62
  • Tell a friend

    Love Neowin? Tell a friend!