Networking problems w/ DSL and hub


Recommended Posts

Okay recently our ISP, Qwest, merged with MSN.

Therefore we got an MSN DSL modem in the mail.

Now, before, with the Cisco 675 DSL modem, I just plugged it into the uplink on our network hub, plugged the other computers in the house into the other ports, and everything worked fine- internet on all 3 computers.

Now, however, with this new modem (NetDSL 800) I can only use one computer connected to the hub at a time. If I connect another computer it says "network error, IP conflict" or something very similar. If I try to renew the IP on whatever computer isn't working, it just hangs for a while then says there was an error renewing the IP.

Any ideas on how to get all the computers to work on the hub?

Keep in mind I'm not very well versed in this area, so the simplest answer possible would be good :)

Link to comment
https://www.neowin.net/forum/topic/3487-networking-problems-w-dsl-and-hub/
Share on other sites

Nope same exact hub, and I agree that it doesnt' seem to be assigning seperate IPs.

  Quote
Originally posted by poolman

I don't know anything about DSL, but, maybe you check the DHCP setting under your network. I know a router automatically does this for you and you have to disable it under yor network settings. Maybe you can make sure it is enabled??

Hope this helps

poolman

Um so is DHCP supposed to be on or off???

a hub is not a router, its a hub. it just transfers data, it has no real brain besides determining where the info is to go.

on the rare times you can plug a dsl or cable modem into uplink, its a fluke with the way the isp's network is set up. if it does not work now you cant do anything about it.

options open. buy a second NIC and then use your computer as a router, for the other computers. or buy a router. option 1 is best costs like 10 bucks. (CDN)

anywho, sorry to tell you the bad news

I used to be on cogeco @home and i could share with just a hub, then i moved back to Ottawa with rogers@home and no more hub share, DHCP (dynamic host config protocol) gives each computer a unique ip addr. each computer must have a unique ip. the sharing of the net with a uplink port on a hub is just luck given the isps config. by all technical means it should not work, but it does :)/... sometimes.

you dont have to have dhcp id you dont want to, you could set ip for each computer if you wanted to, but dhcp makes it easier, and he is right the only way the "uplink-hub" works is if dhcp is enabled, that way you get your ip from a dsl server.

again, 10 buck and 5 mins solves the entire problem

the uplink port is for upgrading your hub. say you have a 4 port hub and get a 5 or 6 comp, you dont need to buy a new 8 port, you can buy another 4 port and plug it into the uplink port and it acts as a 8 port, more or less.

hubs are chain-able by using the uplink port. if someone knows a way to make any connection work over uplink PLEASE PLEASE tell me!!

ok so you choose a "host" computer, say yours, this computer must be on for the others to use the internet. in that computer there are to network cards. 1 connects to the dsl modem, the other connects to the hub in a normal jack. all the others connect to the hub like normal. then in xp go to the network properties box and tick "share connection" for the dsl network card. a little salt for flavor stir, mix garnish with lime. ta-da

  Quote
Originally posted by Killa-b

ok so you choose a "host" computer, say yours, this computer must be on for the others to use the internet. in that computer there are to network cards. 1 connects to the dsl modem, the other connects to the hub in a normal jack. all the others connect to the hub like normal. then in xp go to the network properties box and tick "share connection" for the dsl network card. a little salt for flavor stir, mix garnish with lime. ta-da

Love that ending! Thats Great

  Quote
Originally posted by Killa-b

ok so you choose a "host" computer, say yours, this computer must be on for the others to use the internet. in that computer there are to network cards. 1 connects to the dsl modem, the other connects to the hub in a normal jack. all the others connect to the hub like normal. then in xp go to the network properties box and tick "share connection" for the dsl network card. a little salt for flavor stir, mix garnish with lime. ta-da

Love that ending! Thats Great

  Quote
Originally posted by Killa-b

ok so you choose a "host" computer, say yours, this computer must be on for the others to use the internet. in that computer there are to network cards. 1 connects to the dsl modem, the other connects to the hub in a normal jack. all the others connect to the hub like normal. then in xp go to the network properties box and tick "share connection" for the dsl network card. a little salt for flavor stir, mix garnish with lime. ta-da

Thanks, that's about what I figured you would have to do... I've messed around with sharing a dial up connection the same way.

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • The first link on the github page gives me a very, very red page warning me about phishing........
    • Hey Nick! 👋 No worries at all — you're not alone in this, and it's great you're asking for help. Let me walk you through a simple, step-by-step fix using the tool mentioned on that AOMEI Partition Assistant guide — it really does the trick for many people with this exact issue! ✅ Here’s how to restore your USB back to full 256GB on Windows 11: Download & Install AOMEI Partition Assistant Go to the link you shared: AOMEI Partition Assistant and click the Download Freeware button. Insert your USB stick (Sandisk Ultra 256GB) Make sure it's properly connected. Wait for the system to detect it. Launch AOMEI Partition Assistant Once open, you'll see all your connected drives listed. Locate your USB Drive Look for the one that says something like Disk X – Removable and shows only 3.1GB or so. Right-click on your USB Drive’s Partition Then select Delete Partition → confirm the deletion. Now, right-click on the unallocated space (it should now show full unallocated capacity) Choose Create Partition → format it as FAT32 or exFAT (recommended for larger drives) → click OK. Click “Apply” in the top left corner Then hit Proceed to execute the pending operations. Wait a bit... and boom! 🎉 Your USB should now be restored to its full 256GB capacity!
    • When Facebook bought Beat Saber, they promised exactly this would never happen. Facebook can’t not lie.
    • Depends on what you mean by "this data". Nvidia can show you quite a few of those as well in their performance overlay, and I guess they might've assumed that if anyone wants to see more, they'll just use Afterburner as the de facto standard. As for real framerate vs framegen framerate, I don't think they exactly want you to know, given that their marketing has been strongly focused on hiding the real framerate and pretending the generated one is all that matters...
  • Recent Achievements

    • First Post
      Fuzz_c earned a badge
      First Post
    • First Post
      TIGOSS earned a badge
      First Post
    • Week One Done
      slackerzz earned a badge
      Week One Done
    • Week One Done
      vivetool earned a badge
      Week One Done
    • Reacting Well
      pnajbar earned a badge
      Reacting Well
  • Popular Contributors

    1. 1
      +primortal
      713
    2. 2
      ATLien_0
      279
    3. 3
      Michael Scrip
      209
    4. 4
      +FloatingFatMan
      201
    5. 5
      Steven P.
      131
  • Tell a friend

    Love Neowin? Tell a friend!