Setting correct input delays on Harmony remote


Recommended Posts

I've got a Harmony 550 and a Samsung SlimFit 30" TV

To switch inputs on the TV, I have to go into the menu and scroll through them. Initially, the remote would pause for about 500ms between key presses, so it would scroll through the inputs list rather slowly.

I went into the harmony app and brought up the speed delay screen for the TV. I set the inter-key and input delays to 100ms. However, this only seemed to make things slower. The remote now paused about a second between 'key presses'. Well, the light would stay on for the whole second, so I'm not sure if it sends the signal and then waits a second, or if it sends the signal for a full second before sending the next one. Either way, it got slower, not faster.

So I went back in and set both delays to 0ms. Now the delay is closer to 2 seconds. This isn't making any sense. Can someone help me out here? What's the difference between the inter-key delay and the input delay? When is each delay applied?

did you mean "enter-key delay" and "input delay" ?

since I'm putting together a home theater with my roommates, I've been reading up on Harmony remotes. And by what I have read:

"enter-key delay" is the amount of time it takes between key-press and sending the signal to the device.

"input delay" is the amount of time it takes to switch from one device to another.

but by what you said... it sounds like the timings are wrong. If you don't remember what you've changed.. I would suggest starting from square one... wipe the remote and set it up again.

I should be getting my Harmony 360 by next week (I hope), so maybe I could give more help by then.

not quite. after some searching on logitech's support site, I tracked it down:

Power On Delay. When a device receives a PowerOn command, it takes a certain amount of time to "warm up" the device and resume normal operation. For most devices this happens very quickly, but for some devices, such as televisions and receivers, it can take up to 3000 milliseconds (three seconds).

Inter-key Delay. When a device receives an infrared command the device is considered"busy" while it processes the command. The amount of time required before the device will respond to another command is known as the inter-key delay, and normally ranges from zero to 300 milliseconds. Devices with long inter-key delays take longer to respond to multiple infrared commands (e.g., when changing television channels).

Input Delay. When a device switches inputs (e.g. goes from Video 1 to Video 2) the device is considered "busy" while it processes the command. The amount of time required before the device will respond to another switch input command is known as the input delay, and normally ranges from 500 to 3000 milliseconds. Devices with long input delays take longer to change inputs.

Inter-Device Delay. When an infrared command is sent for a particular device, each device in your system will receive the command, but only one will respond to it. The other devices will ignore the infrared command. Sometimes, when this happens, a device will ignore the infrared signal and then stop accepting infrared commands for a period of time. This period of time is known as the inter-device delay. During this time no infrared signals are generated by the remote. In rare cases this delay can be several seconds.

Right now I'm back at defaults for everything. I just swapped out my regular cable box for a shiny new HD converter, and I've been sick the last few days, so I haven't gotten around to changing anything yet. I may try a few things when I get home today.

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • From what I understand, RAID 1 makes a copy of one disk. How does it do this? If something happened to one drive, could I take the other one out, plug it into a PC and use it like a normal disk? I have two hard drives that have the same information on - a bit of protection if one drive fails. But I've just been manually copying the data twice.
    • Microsoft SharePoint gets Modern Page Templates to speed up page creation by Paul Hill SharePoint, Microsoft’s enterprise content management solution that allows organizations to set up internal pages and share documents, has just got a big update with the new Modern Page Templates. Microsoft said that it’s going to be rolling out the feature to customers globally between early July and early August. Organization members that want to set up pages on SharePoint using the new templates can do so from multiple entry points including the Site Home (the home of a Communication or Teams site), App Bar (the persistent navigation pane on the left of SharePoint), and the New Web Part (a webpart that displays and creates news posts directly on pages). By giving colleagues multiple access points to the new templates, there’s more chance they’ll be found and used. By including plenty of swanky templates, Microsoft is making it so you can spend less time designing pages, and more time filling them with content that really matters. If you want to create a new page using the templates, just go to New > Page and select a template “From Microsoft”. If you were making a news post, you would go to New > News post then you’d be presented with the new Template Gallery where you can select a custom template created by your colleagues under “Saved on this site”. While these new templates are coming to customers globally next month, Microsoft is already busy working on new features to make templates easier to discover and make them more useful. For example, it is building tenant-wide custom templates that can be published across sites for organization-wide use, and it’s working on Copilot templates that you can use when creating pages with Copilot. Neither of these features was given a release timeline. Customers won’t need to do anything to start using Modern Page Templates as they’ll be available automatically as it rolls out worldwide across tenants. For those who want to dive deeper, Microsoft will be publishing additional documentation and guidance about this feature soon.
    • Times are changing: https://arstechnica.com/gaming...ndows-11-ars-testing-finds/
    • Unless there is “bug” that all of a sudden sends your messages to Meta. Where have I heard this before?!
    • Maybe, just maybe... and it isn't you... there are some people who like the Windows 11 UI (for whatever reason) and want a better backend.
  • Recent Achievements

    • Week One Done
      pcdoctorsnet earned a badge
      Week One Done
    • Rising Star
      Phillip0web went up a rank
      Rising Star
    • One Month Later
      Epaminombas earned a badge
      One Month Later
    • One Year In
      Bert Fershner earned a badge
      One Year In
    • Reacting Well
      ChrisOdinUK earned a badge
      Reacting Well
  • Popular Contributors

    1. 1
      +primortal
      539
    2. 2
      ATLien_0
      205
    3. 3
      +FloatingFatMan
      168
    4. 4
      Michael Scrip
      150
    5. 5
      Som
      126
  • Tell a friend

    Love Neowin? Tell a friend!