Bluescreen on Vista install 90% (x64)


Recommended Posts

Hey guys wassup,

So I got back to england today and wanted to setup my new machine,

Spec: http://asphyxia8489.net/blog/?p=6

I got out my shiny new copy of Windows Vista Home Premium x64, put it in the DVD drive and off it went, I partitioned the drive and began the install, now I'm getting a bluescreen as soon as it hits 90%. I'm baffled.

So I went off installing alternate OSes to see if they suffer similar issues, Windows XP installed fine, minus only using 3GB of my total 8GB of RAM, and obviously Ubuntu 8.04.1 installed fine too.

I ran a full memory diagnostic and everything came up clean, it ran for Four hours BTW

I tried installing Windows Vista with one stick of RAM, two sticks of RAM, swaping them about, even using some old DDR2-667 RAM I had lying around, doesn't matter what I do, same issue.

The bluescreen message is ether PAGE_FAULT_IN_NONPAGED_AREA or IRQL_NOT_LESS_OR_EQUAL

The Motherboard is running on the latest BIOS so thats not the issue.

Anyone have any ideas at all?

Thanks guys

EDIT: Ok in this Run it got to 96%.... so close...

Link to comment
https://www.neowin.net/forum/topic/665778-bluescreen-on-vista-install-90-x64/
Share on other sites

It could be a HD drive problem.

Try disconnecting one (disable RAID in BIOS) OR using a driver disk at start of install (with RAID enabled in BIOS)...

edit: Try making a driver disk with this download (v8.5.0.1032):

http://downloadmirror.intel.com/16760/eng/f6flpy64.zip

Then during the operating system installation, after selecting the location to install Vista, click Load Driver to install a third party SCSI or RAID driver.

Edited by pjak

As already stated in my first post:

ASUS P5Q Deluxe P45 Socket 775 ATX Motherboard

Intel Core 2 Quad Q9450 2.66GHz Socket 775 Processor

Corsair 8GB DDR2-800 (4-4-4-12) RAM

2 x Samsung HD502IJ SpinPoint F1 500GB Hard Drive in a RAID0 Array

ATi Saphire HD 4850 512MB GDDR3

cant believe no ones stated the obvious :p

if its a PRE-SP1 disc then make sure you only have 2GB of ram in. If its a SP-1 integrated disc you should be able to install with all 8GB of ram in. Its a well known problem with Vista NON SP-1 integrated discs. If that still doesnt work take a look at the voltages on the memory. It might be you need to up the voltage for those sticks.

cant believe no ones stated the obvious :p

if its a PRE-SP1 disc then make sure you only have 2GB of ram in. If its a SP-1 integrated disc you should be able to install with all 8GB of ram in. Its a well known problem with Vista NON SP-1 integrated discs.

It's an SP1 disc, and I've already said that I tried it without the rest of the RAM in :)

About the driver boot disc, I assume i'll need to do that via a floppy? Damn, I dont have any of those. Any way I can do it over USB flash drive?

Edit, bluescreened at 7% this time. :D

Two things to check on:

1) At the beginning of the Vista installation (I'm assuming that you're booting off of the DVD) there is a point where the user is prompted to provide 3rd-party disk drivers - if you're installing on a SATA drive, you'll need those drivers from the manufacturer of the motherboard or it's chipset maker.

2) Check with the motherboard manufacturer to see if there are any reported problems with the BIOS & Driver releases you are installing to. Also, if the SATA controller chips have upgradeable firmware, make sure those are upt-do-date AND are working for Vista x64

Hope this helps!

--Scott

At the moment the BIOS is configured for a RAID 0 array of both drives.

I cant see any area at all that gives me the option to load drivers from a disc... :(

At the moment i'm downgrading my BIOS to it's first version to see if vista likes that more, then after the install (i hope) i'll update the BIOS again and hope everything is good :D

EDIT: Vista setup is loading now after the downgrade so we'll see how that goes, I think it was a bad idea to build a new PC after 40 hours with no sleep due to travelling....

Edited by Vegetunks

Update, ok, so now Vista is installed and running, but the Blue-Screens keep coming...

Now the main one is MEMORY_MANAGEMENT

Seriously, this cant be the RAM... The RAM is fine, happy and content in any other box I put it in. Maybe clock it down to 667MHz?

after the Vista installation, install the chipset INF (v9.0.0.1011)...

http://downloadmirror.intel.com/10884/eng/...0.0.1011_PV.exe

matrix storage manager (intel RAID - v8.5.0.1032)...

http://downloadmirror.intel.com/16750/eng/IATA85ENU.exe

and make sure your BIOS is the latest (v1306)...

http://dlsvr.asus.com/pub/ASUS/mb/socket77...DELUXE-1306.zip

and then install video drivers (latest is v8.8)

http://game.amd.com/us-en/drivers_catalyst...64/radeonx-xp64

also, your LAN network driver (v10.64.2.3):

http://www.marvell.com/drivers/files/yk60x64_v10.64.2.3.zip

then don't your sound drivers (and anything else that's displayed as unknown in Device Manager)!!!

the problem you SEEM to be having is HD access...if it fails to read/write the pagefile Windows just blue screens...you just need the correct drivers (as above)...

Edited by pjak
Update, ok, so now Vista is installed and running, but the Blue-Screens keep coming...

Now the main one is MEMORY_MANAGEMENT

Seriously, this cant be the RAM... The RAM is fine, happy and content in any other box I put it in. Maybe clock it down to 667MHz?

You ran memtest on the ram for errors?

As stated already, again, I have already done a four hour memory diagnostic and it showed up clean.

I've got all the latest drivers but am still getting bluescreens :(

This is a real odd one, dosnt make a lot of sense.

I read an article on the ASUS forums that this motherboard dislikes Corsair 4-4-4-12 RAM, yet I lowered the clock speed to 667 and upped the CAS latencys to 5-5-5-15 and had the same issues so it's obviously not RAM related, not to mention of course that I have the same issues with a different stick of RAM entirely (OCZ), it seams to be Vista that is the problem here, nothing else, SP1 seams far more unstable to me then SP0 ever did.

Going to get some sleep now, finally, and hopefully i'll come up with something, if not, guys, keep working your magic and firing ideas at me.

Vista isnt to blame here, its clearly a hardware issue, if it was a vista issue everyone would be getting it but as far as im aware your the only one.

I recently had this problem with my new build and the motherboard was causing all the issues. sent it back and bought a different mobo and it worked perfectly.

Well, it's got to be Vista as Windows XP works fine minus the huge memory difference as do several Linux Distros. Hell, even managed to get Mac OS X to run on it quite easily and error free. Maybe try a different Vista disc?

I would suggest running windows Vista with only 1GB of ram, and see if it BSOD's again. I can't really think of anything else other then bad ram, or faulty hardware....

Vista should only bsod if it detects bad drivers, or bad hardware. Something you are using is not vista compatible fully, and may require another version of the driver.

look online for all your hardware you have, and see if it returns with any vista troubles

If you have Vista installed and up to date then run the system file checker, sfc /scannow, from a command prompt, however as others have stated i'd say it's a hardware issue. Vista is allot more sensitive to hardware errors than any other OS i've tried, so just because you don't have issues with XP, for instance, doesn't mean it's not a hardware fault.

I would suggest running windows Vista with only 1GB of ram, and see if it BSOD's again. I can't really think of anything else other then bad ram, or faulty hardware....

Vista should only bsod if it detects bad drivers, or bad hardware. Something you are using is not vista compatible fully, and may require another version of the driver.

look online for all your hardware you have, and see if it returns with any vista troubles

Well, I've tried running with 2GB of RAM, as a I have 4 x 2GB of RAM. Same issue, ditto for running with different modules.

Try a different Vista disc, like you said.

Ok, I'll see if one of my mates has the x64 version or download a ISO or something.

Someone recommended to me to use VLite to integrate all the drivers into the Disc, anyone think that'd help? I dont seeing as I'm now running all the latest drivers.

However, one thing I have noticed is I downgraded to the Intel Drivers on the ASUS DVD and I couldnt even get to the desktop before it BSODed yet the newer drivers allow for almost unlimited use providing I dont open or close any applications. So MAYBE it'll be fixed in a later Driver release, so that brings me to this question.

How often do Intel release new chipset drivers?

Well, I've tried running with 2GB of RAM, as a I have 4 x 2GB of RAM. Same issue, ditto for running with different modules.

Ok, I'll see if one of my mates has the x64 version or download a ISO or something.

Someone recommended to me to use VLite to integrate all the drivers into the Disc, anyone think that'd help? I dont seeing as I'm now running all the latest drivers.

However, one thing I have noticed is I downgraded to the Intel Drivers on the ASUS DVD and I couldnt even get to the desktop before it BSODed yet the newer drivers allow for almost unlimited use providing I dont open or close any applications. So MAYBE it'll be fixed in a later Driver release, so that brings me to this question.

How often do Intel release new chipset drivers?

Every few months. It shouldn't be the Intel chipset drivers because they aren't actually drivers. They are just inf files that tell the OS more specifically how to configure the hardware.

It's the motherboard, Tested every component minus the processor in a different PC today and vista installed without a hitch, Shame, I cant RMA it because I lost the PnP cap for the processor socket :'(

Damn thats a waste of money... ?90 or so, gone, pulls hair it, going to be another month before I get this machine working now....

Can anyone recommend a good motherboard for a Core2Quad and a ATi 4850 bundled with 8GB of DDR2-800 RAM in 4 x 2GB

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • No its not, there are ton of Youtube videos to get you started, what do you think people did before AI existed?
    • Read this in Humor Simpson 's voice, "Out of my way Moe".
    • You still can, its just under the Transform flyout for WordArt now
    • Likely nothing will be done in corporate America, there have been countless Tesla self-driving incidents. Then again, there have also been countless human operated incidents. It's literally daily news here in Canada, to the extent that it's now odd if we get a day where a collision doesn't get announced on the radio throughout the day...
    • SKG Hand Massager with Heat OS500 hands on by Steven Parker I was offered the chance to test out the SKG Hand Massager with Heat OS500, and full disclosure, they let me keep it regardless of my findings. Anyway, I jumped at the chance due to my long hours sitting at my desk, mousing around. Apologies for the knife cut across the top of the box; that was my doing, being a bit too heavy-handed with opening up the outer packaging. First up, what's in the box: SKG Hand Massager with Heat OS500 1x Type-C charging cable User Manual 1-Year Warranty (card) In short, everything you need to get started. According to the official Amazon listing, here are the key features: Full-Hand Air Compression: OS500 wraps your fingers, palm, and wrist with multi-chamber air compression for a complete hand relaxation experience. The extended massage chamber helps cover more of the hand and wrist area than standard palm-only hand massagers Palm Kneading with 6 Modes & 6 Intensities: Built-in palm kneading rollers add a hands-on massage feel, while 6 preset modes and 6 pressure levels let you choose the comfort level that fits your day—from gentle relaxation to a firmer full-hand massage 3 Heat Levels with Cooling Fan: Choose from 104°F, 113°F or 122°F warmth to suit different seasons and comfort preferences. The built-in cooling fan helps reduce stuffiness during heated sessions, keeping your hand feeling fresh and comfortable Easy Visual Display & Smart Timer: The digital image display clearly shows massage area, mode, intensity, heat level, and remaining time at a glance. Select 10, 15, or 20-minute sessions for quick office breaks, evening relaxation, or everyday hand care Rechargeable, Cordless & Comfortable: A 3000mAh battery supports over 90 minutes of full-function use on a full charge, with convenient USB-C charging. The soft inner lining, smooth ABS/PU finish, and premium black-gold design make OS500 ideal for home, office, or gifting With all that out of the way, here are my own findings. I gave it a try on both left and right hands, and as you can maybe see from the above YouTube Short, (sorry for the shaky video), my whole hand fits in, but my wrist barely enters the Hand Massager. I was able to push through a bit more with my fingertips extending out the other end to get a bit of massaging on the start of my wrist. Usage For some reason, there is a strap that is very difficult to fasten to my wrist with one hand. I am not sure what function it has, and it isn't mentioned in the user manual. The only thing I could find was in the product images that claimed "wrist precision". Unlike the Bob and Brad Hand Massager, this device does not massage the wrist anyway, even though a "wrist mode" is mentioned, which must be for smaller hands than I have, as it is mainly intended for the hand and fingers. In addition, for its steeper price, there are no disposable gloves provided in the box, which is a bit of an issue considering the internal cover (which appears to be elasticated nylon) cannot be removed for washing; so you are left with only one choice: always thoroughly wash your hands before using it. I can imagine this thing getting a bit grimy after a period of use, and that is a bit of a shame. With that said, the buttons on the device, from left to right, do the following: Heat button: 3-level heat control at 104°F, 113°F, or 122°F Mode button: Auto mode Circular mode Soothing mode Relax mode Palm and fingers mode Palm and wrist mode Intensity button: from (First-time users) 15Ka, 25Ka, 35Ka, 45Ka, 55Ka, 60Ka (Intensive relief) Knead button: on or off (6 pressure levels) Power button: Long-press to turn on or off Cooling button: turn on or off the cooling fan Also, in the product imagery, it states there are 36 "custom modes," but nowhere is it listed what these modes are. I can only imagine that they mean a combination of all of the above settings in different intensity levels. The device itself seems to rely on a single "kneading" mechanism located at the palm area of the hand, which spins when in use, and the other massage features are mainly utilized through the air sacs, increasing and decreasing at various levels on the hand and fingers. I am not sure it offered too much relief for someone who is typing and operating a mouse for hours at a time; further testing may be required. It does feel nice, though. Finally, you may be wondering how this fits into the scope of a tech website? Well, let me tell you something: sometimes I sit for up to 15 hours working on Neowin, and although I take breaks in between, it takes a toll on my body. I think in the immediate absence of a partner to apply relief, a good massager like this Hand Massager can shed the strains of the day in just a couple of 15-minute bursts. On the official website, this has an MSRP of $99.99, but luckily for our readers, it is selling at $10 off for just $89.99 right now on Amazon. SKG Hand Massager with Heat OS500 for $89.99 (with $10 off coupon), $99.99 MSRP For me, this gets a thumbs hands(?) down. However, it could be improved by making it so that the protective covering could be removed and thrown into the washing machine, or get yourself some disposable gloves to use with it. As an Amazon Associate, we earn from qualifying purchases.
  • Recent Achievements

    • Dedicated
      Almohandis earned a badge
      Dedicated
    • Dedicated
      JuvenileDelinquent earned a badge
      Dedicated
    • First Post
      DrWankel earned a badge
      First Post
    • Reacting Well
      DrWankel earned a badge
      Reacting Well
    • Week One Done
      Supreme Spray LV earned a badge
      Week One Done
  • Popular Contributors

    1. 1
      +primortal
      505
    2. 2
      +Edouard
      184
    3. 3
      PsYcHoKiLLa
      86
    4. 4
      Michael Scrip
      78
    5. 5
      Steven P.
      76
  • Tell a friend

    Love Neowin? Tell a friend!